|
|
Project of worm gear for lift mechanism
Otisk, Jan ; Malach, František (referee) ; Malášek, Jiří (advisor)
This graduation thesis dwells on a worm gear design for an elevator mechanism in an already existing wheel case with actuator unit S3 for elevator type BOV 320/0,63. The work includes dimensional and control calculation for the worm gear and as an attachment you will find spiral worm and worm gear drawing documentation, including its specific location.
|
|
|
Steam turbine with ejector
Slezáková, Iveta ; Ing.Drahomír Maša (referee) ; Fiedler, Jan (advisor)
The main Target of this diploma is to find some reconciliation with cooperation of turbine and ejector. This work is containing informations about this mechanisms and also its historical development. The merits of this diploma thesis is thermodynamics calculation and proposal of main parameters and proportions of the turbine and the ejector. After this it is follow by the calculation of whole system of the turbine and ejector in consequence with calculation of turbine with by-pass regulation and also comparison of power output with ejector and with by-pass technology.
|
|
|
Traffic characteristics of 2+1 arrangement
Kabeš, Luboš ; Čepil, Jiří (referee) ; Radimský, Michal (advisor)
The thesis discusses the roads in lanes 2 + 1 arrangement in the country and abroad. It focuses primarily analogy of this type of arrangement in our situation, ie on stretches of roads I. classes with an increased number of lanes for slow vehicles to climb. Part of this work is to verify some of the traffic, including traffic flow characteristics compared to conventional two-lane roads, especially in terms of: sectional speed; overtaking; Accident and dependence longitudinal gradient. The work aims to evaluate the foreign experience and achievements of domestic communications options for application configuration 2 + 1 in the Czech Republic.
|
|
|
Selected ČSN Road Design Elements Optimization
Stránský, Jakub ; Čepil, Jiří (referee) ; Kosňovský, Michal (advisor)
The master‘s thesis focuses on the optimization of the design values of curves of the horizontal alignments of the roads. It deals with the comparison of values between czech and foreign standards and differences between them. The practical part examines the values of the real speeds of vehicles passing through the curves of various parameters that were measured during measurements of selected curves during 2014. From these data a new design values are derived that could be used for the design of horizontal alignments.
|
|
|
Analysis of the acoustic signal to detect the speed of vehicles
Koníčková, Tereza ; Beneš, Petr (referee) ; Klusáček, Stanislav (advisor)
The aim of this Bachelor thesis is to create software for sound signal analysis of a passing car with the aim to determine the driving speed. This work describes single methods of a car velocity measurement and it is submitting a new method of velocity measurement with using the Doppler principle at sound signal analysis. My work proved, that it is possible to use this method to determine the speed of vehicles.
|
|
|
Automotive Alternator Innovation
Volek, Martin ; Hýsek, Roman (referee) ; Hájek, Vítězslav (advisor)
The work deals with the analytical electromagnetic design of automotive claw-pole alternator 14V/120A. This design is verified in program Maxwell with a RMxprt tool. The results of both calculations are compared. Designed alternator is also compared with the results measured in the laboratory on the alternators of similar type. Furthermore, there are analyzed individual power losses of machine and listed options of reducing these losses, which results in an increase in overall efficiency.
|
|
|
Design, optimization and full load circuit simulation of the surface mounted permanent magnet machine
Bláha, Martin ; Ondrůšek, Čestmír (referee) ; Kurfűrst, Jiří (advisor)
This thesis deals with the possibility of using the finite elements method for the analysing of synchronous permanent magnets machines. The aim of this work is to discuss the possibility of the machine design more effectively with using the finite elements method and Maxwell software for the simulations. On the created parametric model, simulations were performed according to master thesis assignment. The aim of this work is to determine induced voltage, iron losses, machine inductances and make a permanent magnets demagnetization analysis. From simulations results the machine efficiency is calculated. The parametric model was used for the optimization of selected parameters. From results of optimization new dimensions of permanent magnets was obtained. Machine efficiency was increased by new permanent magnet material and optimized design.
|
|
|
Design of Communication system among Moving Vehicles
Klampár, Marián ; Polívka, Michal (referee) ; Škorpil, Vladislav (advisor)
The purpose of this thesis is to show up possibilities of inter-vehicle communication and to introduce new approaches in communication for the purpose of enhancing the security and the fluency of vehicle transportation. This thesis also highlights vulnerabilities in communication. The main goal is the analysis of existing technology and the design of protocol for data transfer with focus on minimizing handover time of informations. Part of the design is a simulation of communication based on acquired information.
|
|
| |
|
|
Traffic Doppler Radar
Kulig, Radomír ; Józsa, Ladislav (referee) ; Šebesta, Jiří (advisor)
This work deals with problematics of speed measurement of an object with a Doppler radar. This radar communicates with other environment through RS232 interface. The complete solution of this Doppler radar is provided in the thesis. There are electrical schemes of all parts and program to control microcontroller in this work. Speed measurements for the radar are summarized in the end of the work.
|
guest ::
