|
|
Study of interaction of charged catanionic vesicles with oppositely charged polyelectrolytes
Havlíková, Martina ; Lehocký, Marián (referee) ; Táborský, Petr (referee) ; Mravec, Filip (advisor)
The presented dissertation is focused on positively charged catanionic vesicles and their interactions with oppositely charged hyaluronan. The catanionic vesicles were composed of ion pair amphiphile of hexadecyltrimethylammonium-dodecyl sulfate (HTMA-DS), a positively charged double-chain surfactant that electrostatically stabilized the vesicles and cholesterol. Cholesterol may strongly affect the physico-chemical properties of the vesicles, therefore it was necessary to determine its optimal amount in the membrane. Especially, the size and stability of vesicles were studied by dynamic and electrophoretic light scattering, membrane microviscosity by fluorescence anisotropy and hydration of the outer part of the membrane by generalized polarization. It was found that vesicles show ideal properties at a cholesterol content about 40 mol.%. These catanionic vesicles interacted with hyaluronan regardless of its molecular weight. Visible aggregates were observed around their isoelectric point, but they disintegrated with increasing polymer concentration. However, this decay was different for different hyaluronan molecular weights. An increase in ionic strength, or more precisely concentration of sodium chloride above 25 mM had a destabilizing effect on both uncoated and hyaluronan coated vesicles. It was also interesting that increasing the ionic strength affected the microviscosity of the membrane, which became more fluid, but there were no significant changes in the hydration of its outer part. The presented work is also focused on the preparation and characterization of a new type of catanionic vesicles, where the cationic surfactants HTMAB was replaced by Septonex. The same methods were chosen for their characterization as in the case of the HTMA-DS vesicles. This exchange of surfactants had a major effect on the resulting properties of the vesicles, which are stable even at very low cholesterol content. In accordance with long-term stability, a suitable concentration of cholesterol was chosen from 15 mol.% and higher.
|
|
|
Production technology of wine sausage with reduced salt content
Martonová, Rebeka ; Punčochářová, Lenka (referee) ; Mikulíková, Renata (advisor)
The aim of this bachelor thesis was preparation of wine sausages with reduced salt content, followed- up by sensory analysis. The theoretical part generally characterizes meat and meat products, sodium chloride and its importance in food. In the next chapters, the paper deals with sensory analysis of samples and analytical method for determining the concentration of elements in biogenic samples, in particular inductively coupled plasma - optical emission spectrometry. The experimental past focuses on the evaluation of data from sensory analysis using the Kruskal- Wallis and Spearman test. The samples were analyzes using ICP-OES method. The analysis determined the concentration of sodium and potassium in the samples before and after roasting.
|
|
|
Study on PHA accumulation by cyanobacteria
Pacasová, Viktorie-Alexandra ; Slaninová, Eva (referee) ; Obruča, Stanislav (advisor)
This bachelor thesis was focused on studying the influence of selected stress factors on PHB production in strains of cyanobacteria Synechocystis sp. PCC 6803 and Synechocystis salina CCALA 192. Cyanobacterial stains were cultivated in multicultivator and as a stress factor an increased salt (sodium chloride) as well as a mixture of acetate and -butyrolactone was selected. The PHB content in cyanobacteria was determined by gas chromatography. In addition, the content and presence of pigments in cyanobacteria strains was determined by pigment extraction as well as using direct spectroscopy of whole cells. When cultivated with an increased salinity, the hypothesis of an increased PHB production was not confirmed most likely due to and overstressing the Synechocystis salina CCALA 192 cultures with increased salt content, constant illumination of multicultivator and by nitrogen limitation due to the used medium. When cultivated with the mixture of acetate and -butyrolactone the stains were analysed in the same way as in the cultivation with an increased salinity. In this case, the presence of 3-hydroxybutyrate and 4-hydroxybutyrate copolymer was determined in the stain cultivated with the mixture of acetate and -butyrolactone. During this cultivation, a positive effect of initial concentration of cells in the cyanobacterial cultures combined with continuous illumination and the type of nitrogen-limiting type of medium on the growth rate of selected stains was observed.
|
|
|
Use of stress factors for the production of lipid substances by yeasts of the genus Metschnikowia
Tručková, Marie ; Márová, Ivana (referee) ; Němcová, Andrea (advisor)
This Master´s thesis consists of two parts. The theoretical part is focused on the influence of various stress factors in the cultivation process, such as osmotic stress, oxidative stress, dehydration, cultivation time, pH or temperature on yeasts of the Metschnikowia genus. The practical part deals with osmotic and oxidative stress. Oxidative stress was performed under two different conditions (various cultivation time and temperature). The properties of yeast production were monitored mainly by gas chromatography and marginally also by flow cytometry. The analysis was performed for Metschnikowia pulcherrima, Metschnikowia andauensis, Metschnikowia chrysoperlae, Metschnikowia sinensis, Metschnikowia zizyphicola and Metschnikowia shanxiensis strains. The results showed that both oxidative stress and osmotic stress induce better lipids production. The amount of lipids, especially the fatty acid composition, also varied depending on the strains studied and the culture conditions used. The production of unsaturated fatty acids was further demonstrated in this work. The most suitable medium for the production of lipids and unsaturated fatty acids was the salt medium. It is clear that yeasts of the genus Metschnikowia are highly adaptable yeasts. Therefore, they might be potentially auspicious biotechnology producers.
|
|
|
Use of energetic by-products and other secondary raw materials for the alpha gypsum production
Moldrzyk, Jan ; Jiroušková, Kateřina (referee) ; Dvořák, Karel (advisor)
Thesis focus on the longterm research in an area of alpha gypsum production by non pressure method in chloride salt solutions production, which is researched by Institute od technology of building materials and components, Faculty of civil engineering for many years. The result of given research is non pressure equipment for alpha gypsum production. The scope of this research was to make a production of alpha gypsum more efficient through modification of the facility itself and through an optimalization of dehydration process. The scientific aim of this process was to compare an influence of dehydratation solutions of CaCl2, NaCl and KCl on the final product provided that molarity of solutions was at the same level.
|
|
|
Plasma diagnostics of electric discharges generated in selected configurations in liquids
Vašíček, Michal ; Bartlová, Milada (referee) ; Kozáková, Zdenka (advisor)
My diploma thesis is focused on a comparison of direct-current and high frequency (15-80 kHz) electric discharge, which generates non-thermal plasma in water solution of sodium chloride. Mainly current-voltage and Lissajous charts are discussed in the first part of this thesis. These charts describe different discharge phases: electrolysis, bubble formation, discharge breakdown and discharge regular operation in a pin-hole of a dielectric barrier. Influence of frequency, electrolyte conductivity, thickness of the diaphragm (or length of the capillary) and pin-hole diameter on discharge breakdown and bubble generation was studied, too. Measurements were realized in a polycarbonate reactor with total volume of 110 ml, which was divided by a changeable polyacetal insulating wall. This wall divided the reactor into two approximately equal spaces with one stainless steel planar electrode in each part. The Shapal-MTM ceramic discs (thickness of 0.3–1.5 mm and diameter of the central pin-hole of 0.3-0.9 mm) were mounted in the centre of the insulating wall. Initial conductivity of sodium chloride solution was chosen within the interval of 100900 S/cm. The second part of my thesis compares an influence of the direct-current (DC) and high frequency (HF) power sources on physical solution properties (conductivity, pH and temperature) and generation of hydrogen peroxide. A plasma reactor with total volume of 4 l and with mixing set up was divided into two equal spaces with one planar platinum electrode in each part. Diaphragm with thickness of 0.6 mm and pin-hole diameter of 0.6 mm was installed in the middle of the separating wall. Experiment was held at discharge operation of 45 W for 40 minutes with both power sources. Detection of hydrogen peroxide was realised by using a titanium reagent forming a yellow complex, which was analysed by absorption spectroscopy. If HF discharge power is plotted as a function of applied frequency, exponential decrease of frequency with increasing power can be observed. Higher breakdown voltage is necessary for thicker dielectric barriers, on the other hand for bigger diameter of the pin-hole lower breakdown voltage and higher power is needed in DC as well as in HF regime. Breakdown voltage is decreased by the increasing conductivity in both regimes; due to more charge carriers in the higher conductivity lower breakdown voltage is needed. However frequency in HF regime and DC discharge power increases. HF discharge power is decreased by the increasing conductivity. Solution conductivity and temperature are increased by initial conductivity value in both discharge regimes. Solution pH drops to acidic conditions when HF or DC positive regime is applied due to the generation of reactive species and electrolysis (in DC regime). However solution becomes alkaline when DC negative regime is applied. Concentration of hydrogen peroxide is produced linearly when HF or DC negative regime is applied and it depends on initial solution conductivity.
|
|
|
Preparation of high performance sulphate binder by nonpressure method
Urban, Karel ; Novák, Jan (referee) ; Dvořák, Karel (advisor)
Institut of Technology building materials and components in FAST VUT Brno is for several years engageding by research of unpressurized production of high sulphate binders and also by developing a dehydrating apparatus. This work follows on this research. The main aim of this work is to prepare the alpha calcium sulfate hemihydrate by method of dehydration in the various solutions the chloride salts of the same molal concentration in an innovative dehydration apparatus. Another aim is monitoring the influence dehydrating solutions on the basis of KCl, NaCl and CaCl2 on the properities of made gypsum.
|
|
|
The development of composites based on inorganic binders designed for the extreme applications
Janoušek, Petr ; Šácha, Libor (referee) ; Dufka, Amos (advisor)
The topic of this master's thesis is the development of composite materials based on inorganic binders for use in extreme conditions. It means especially geopolymeric or alkali activated materials (AAM) based composites. The theoretical part of this thesis summarizes knowledges about the development and use of alkali-activated materials, their structure and mechanisms of their formation. It also deals with the applicable raw materials for AAM and their exciters, which are in particular water glass and sodium hydroxide. There also have been a summary of the effects of high temperatures and chemicals on the mechanical properties of AAM and the requirements of standard EN 1504-3 for repairing materials. The task of the practical part was to develop a repair mortar for concrete structures based on AAM so that its production was as simple as possible, ie one-component materials. Gradually six recipes have been develeoped. Test specimens made from these recipes have been putted to selected tests according to the requirements of ČSN EN 1504-3.
|
|
|
Diagnostics of Diaphragm Discharge in Water Solutions and its Application for the Nanomaterials Surface Treatment
Dřímalková, Lucie ; Brablec, Antonín (referee) ; Janda,, Mário (referee) ; Krčma, František (advisor)
The exact mechanism of the discharge in liquids ignition is not sufficiently known up to now. Although during the last years was achieved the great progress and overloading which some of them are written in this theoretical part of thesis. This thesis is divided into two experimental parts. When the first part deals with diagnostics of diaphragm discharge in electrolyte solutions and the second part is focused on its use for uncoiling (higher homogenization) of carbon nanotubes in solutions. In experiment 1, three different sized (4 l, 100 ml, 50 ml) diaphragm discharge configurations were used to diagnose diaphragm discharge in electrolyte solutions. Diagnostics is done through current and voltage waveforms with the addition of synchronized ICCD camera images that have been connected to a four-channel oscilloscope. The V-A characteristic can be described by three events occurring in the electrolyte solution with a gradual increase in voltage. Slowly increasing of the voltage in the solution leads first to electrolysis. The next phase is the formation of microbubbles or bubbles, which is characteristic of the curve by a slight decrease in the increase of the current passing between electrodes. The sudden increase in the current flow is characteristic of the last phase, namely the discharge phase. The distance of the electrodes from the diaphragm does not significantly affect the V-A characteristic. The higher diameter of the pin hole, therefore, has a higher voltage, but this does not affect the origin of bubble generation or breakdown. The higher thickness of diaphragm, the higher voltage is needed to the beginning of the bubbles generation, and consequently the discharge breakdown. Comparison of the voltage of the start generation of the bubbles and breakdown for PET diaphragms and diaphragms from the ceramic there was no mark able difference. One of the most important parameters is the conductivity of the electrolyte solution. The lower voltage is needed for the start generation of the bubbles at the higher solution conductivity, and also the discharge generation is observed at a lower breakdown voltage. The second experimental part is focused on the study of the diaphragm discharge effect on carbon nanotubes. A specially designed U-shaped reactor is used to modify carbon nanoparticles. Tap water and aqueous solutions of organic compounds are used as the electrolytic solutions. The discharge is generated by a non-pulsed DC high source with a voltage in the range of 0-2.8 kV supplied to platinum electrodes located in the electrolyte solution. The experimental results have shown that the diaphragm discharge has positive effects on the disintegration of clusters and agglomerates of carbon nanotubes. The primary effect on disintegration is probably the shock waves generated by the discharge. It turned out that it depends on the electrode configuration, where the treatment in anode space has far greater effects than the treatment in cathode half of the reactor. Effects of carbon nanotubes disintegration in solution are long-lasting and the treatment effect is not loosed after several months. There were detected no significant changes in the structure of plasma-treated nanotubes by Infra-red spectroscopy.
|
|
| |
guest ::
