|
|
Study of torque vectoring clutch design
Cupák, Václav ; Porteš, Petr (referee) ; Fojtášek, Jan (advisor)
This work deals with the design of right and left torque vectoring control used in heavy commercial vehicle powertrains. The beginning of the work is focused on the description of the active differential system and on the clutches used in the automotive industry. Then the basic parameters of the experimental vehicle are defined and the choice of the clutch conception is made. Subsequently, calculations of geometric parameters of clutches and verification of their heat capacity is made. Conceptual design of the control mechanism is discussed in the last chapter. The aim of the work is the draft of the possible type of control mechanism for the given system with the possibility to use the information obtained for the further development of this system.
|
|
|
Modern Tractor Transmissions
Bartošová, Daniela ; Řehák, Kamil (referee) ; Prokop, Aleš (advisor)
This Bachelor thesis concerns an overview of the modern trends in the area of tractors transmissions. It explains the reason why both the power shifts and the continuously variable transmissions. Further on, this thesis emphasizes the innovative elements of transmission concept at selected tractor manufacturers.
|
|
|
Chain Conveyor
Štěpán, Marek ; Dlesk, Daniel (referee) ; Škopán, Miroslav (advisor)
The aim of this diploma thesis is to design the control picking unit for the storage system Multitower. This work deals with the storage of rods, safety requirements and design of structures. The design part solves the actuator design, choice of chain tensioning system and torque transmission. The strength analysis of important components is solved in last part.
|
|
|
Design of magnetorheological clutch.
Nováček, Vladislav ; Dočkal, Aleš (referee) ; Roupec, Jakub (advisor)
This thesis deals with the design of the magnetorheological (MR) clutch. The extensive literature research with particular conclusions to each design variant of MR clutches or brakes has been done in the first part of the thesis. The second part of the thesis describes the design of the actual MR clutch based on the results of the analytical calculation of the magnetic circuit. Finally, the experiments verifying the function of the key segments of the clutch, and the whole clutch are summarized in the third part of the thesis.
|
|
|
Vibration diagnostics of electrical machines
Hlaváček, Tomáš ; Hájek, Vítězslav (referee) ; Janda, Marcel (advisor)
Master’s thesis deals with the influence simulated unbalance vibration level asynchronous motor. First is focused introduction to the problem of vibration. Another part is introduction with machine construction and vibrations in machines. Introduction with methods of measurement. The last part is vibration measurements with simulated imbalances.
|
|
|
Using brushless d.c. motor to drive servo-unit with safety function
Rudolf, Ladislav ; Mišurec, Jiří (referee) ; Prajzner, Václav (advisor)
In this work, a proposal for BLDC motor control, which will be used as a drive linear actuator. Control with microcontroller focuses mainly aspects such as motor mode, regenerative mode, measuring rotor position sensors and measuring the motor current, which corresponds to the moment. The result of the work is focused on upgrading the existing Honeywell actuator, where the processor-controlled BLDC motor to replace the existing system and take over the actuator working function and emergency function.
|
|
|
Design of MR clutch water cooling
Musil, Marek ; Strecker, Zbyněk (referee) ; Roupec, Jakub (advisor)
This paper describes the design and manufacture of water refrigeration for magneto clutch. MR clutch cooling problem was solved by designing of several variants of which was finally chosen the best. Model of water cooling was developed and subsequently made. The cooling is consolidated on a stator of MR clutch. Cooling completely surrounds the body of an MR clutch and thus achieves a high heat transfer between the cooling system and cooled. The proposal was developed with a view to good foldability, so its use is not complicated.
|
|
| |
|
| |
|
|
Solution technology of manufacturing for part "disc of coupler"
Borek, Vít ; Osička, Karel (referee) ; Mouralová, Kateřina (advisor)
An introduction to main principles of coupling and description of basic types has been done. An analysis of the given component and a proposal for suitable intermediate was made. A selection of machines and tools for individual operations has been done. A proposition of technologic process and enumeration of machines times was proposed. Economic evaluation containing costs for tools, cooperation, workmen’s wages, intermediate and energy for operating machines has been calculated.
|
guest ::
