|
|
Accelerate handling strength in 2K PUR adhesives
Slatinská, Jana ; Žák, Ladislav (referee) ; Kubíček, Jaroslav (advisor)
This paper is devoted to accelerating the time to obtain the handling strength of two-component polyurethane adhesive, which was newly purchased by the company Magna Exterios (Bohemia) and had to be tested. In order to speed up the analysis of the problem, methods of IR emitters and temperature chambers were selected to be compared with curing using only the ambient atmosphere. In the second part of this paper, the maximum strength of the bond which withstand the test without damage was measured. The results show that the method of accelerating curing process using an IR emitter is the fastest, but the economic side of things must be taken into account, because it is also the most expensive option of acceleration. The temperature chamber is almost twice as slower, but cheaper. At the end of the thesis, the economic efficiency of the new adhesive line solution is evaluated and how much money can be ideally saved.
|
|
| |
|
| |
|
|
Regulation system for climatic test chambers
Burian, Jan ; Palíšek,, Libor (referee) ; Polsterová, Helena (advisor)
This paper contains 5 main parts. The first deals with the general description and properties of the climatic chambers, their individual parts and how these parts work. The second part deals with the chamber of Angelantoni CH 340. In detail is described how the chamber works and there is description of this chamber up to individual parts. The third part deals with the reconstruction project, the possibilities of reconstruction and the method that the chamber reconstructed. The fourth part describes the hardware that had to be selected and replaced and which parts of the chamber had to be modified. In the last part is a description of the program that controls the chamber after the reconstruction.
|
|
|
Mathematical-physical analysis of climatic chamber
Repko, Ilia ; Bílek, Michal (referee) ; Maxa, Jiří (advisor)
This work deals with the mathematical and physical analysis of the climatic chambers. The theoretical part describes the issue of climatic chambers, software SolidWorks and ANSYS Fluent, basic equations describing fluid status and fluid turbulence. The practical part of the thesis is to create the model of climatic chamber in CAD system SolidWorks and simulation of flow and and temperature distribution by ANSYS Fluent. At the end of the work the results are analyzed and evaluated.
|
|
|
SW for control of climate tests
Fedor, Denis ; Richter, Miloslav (referee) ; Petyovský, Petr (advisor)
This thesis deals with control of a specific climate chamber used for various climate tests. Therefore its elaboration starts with the identification of properties of this climate chamber and basic design of its control. This is followed by measuring the temperature distribution in its internal space in order to verify the usability of this climate chamber. The thesis also does not omit a description of the communication options between climate chamber and application for control of climate tests. The next part of this thesis concerns the design and implementation of the application for control of climate tests itself. On its output is a report of the performed climate test. In the end this thesis contains the description of program testing in the real operation of the company and other possible improvements of the implemented program.
|
|
|
Computerized Climatic Test Chamber Control
Pálka, Václav ; Kubinec,, Peter (referee) ; Frýza, Tomáš (advisor)
Diplom work describes a proposal and the design of the device for controlling the temperature test in a climatic chamber Heraeus and the creation of software for operating equipment. Work describes in detail the design and construction interface for the climate chamber, with which will be able to run automated test sequences and the development of the firmware and the operating software to start the temperature test.
|
|
|
Measurement of precise capacitance decade in environmental chamber
Schinneck, Jakub ; Bartoň, Jan (referee) ; Havlíková, Marie (advisor)
This bachelor’s thesis deals with the control capacitance decade in a climatic chamber. The theoretical part introduces a capacitance decade M525 of the MEATEST company and the program Caliber of the same company. It introduces the methods of capacitance measurement. In the bachelor’s thesis there is the calculation of the uncertainty of measuring devices. On the basis of the lowest uncertainty, we choose the most suitable measuring device. The practical part describes the measuring with the use of prepared procedure for verification of the capacitance of programmable decade. The last part contains the evaluation of the measurement results and their comparison with the manufacturer's specifications.
|
|
|
Determination of climatic factor on the degradation of various solar cells types
Peroutka, Tomáš ; Jandová, Kristýna (referee) ; Vaněk, Jiří (advisor)
In this work are discussed photovoltaic cells. There are also discussed basic concepts of radiation source for solar cells. Also mentioned the issue of semiconductors and even the history and evolution of the solar cells. A large part deals with possibilities of photovoltaic cells degradation. In one chapter is an attempt to bring some types of photovoltaic cells and a description of the production of these modules.The practical part deals with photovoltaic modules degradation and its evaluation. Following part compares measured values with the values provided by producer of photovoltaic modules.
|
|
|
Design of climatic chamber
Novák, Petr ; Šperka, Petr (referee) ; Frýza, Josef (advisor)
This bachelor thesis deals with the construction of climatic chamber, which allows continual change of temperature of air within the range of -10 to 50 °C and continual change of relative humidity of air within the range of 10 to 90 %. The chamber is going to be connected to optical tribometer or to Mini Traction Machine (MTM). Both these devices serve for observation of tribological processes in laboratory conditions. Climatic chamber is going to approximate these laboratory conditions more to the real ones by the modification of temperature and air humidity. In the thesis there is stated a concept of particular climatic units, a concept of the arrangement of these units and consecutive constructional solving of the whole device with the emphasis on simple construction, low charges of production, assembility and small proportions of the whole construction
|
guest ::
