|
|
Numerical Modelling of the Light Source
Pavelka, Adam ; Koňas,, Petr (referee) ; Kadlec, Radim (advisor)
The master’s thesis deals with photometry units used in light engineering. There are defined the methods of modelling the illumination systems, their advantages, disadvantages and possibilities of using. Furthermore, the thesis deals with modelling of two illumination systems by ray-tracing in programming environment of MATLAB. The master’s thesis describes the analysis of the problem and the program designing process. Acquired model results are then compared with the real measurements of both illumination systems which allow the discussion of the results and the deviations of the models.
|
|
|
Draft tube role in hydraulic turbine performance
Havlát, Pavel ; Himr, Daniel (referee) ; Rudolf, Pavel (advisor)
This bachelor’s thesis deals with the problems of draft tube. It contains basic description of draft tubes, their division and possibilities of their utilizations. Further, this thesis focuses on description of draft tubes, their efficiency, losses and ways to eliminate these losses. One part of this work also mentions basic relationships required for computing length of draft tube, velocity of the fluid in the draft tube and others.
|
|
|
Conception of a conical splitter for wood
Stejskal, Jan ; Pokorný, Přemysl (referee) ; Hloušek, David (advisor)
This bachelor thesis consists of an introductory research part and a structural draft of a conical wood splitter with typed technical parameters and maximal log length and width. The thesis contains computing and strength examination of chosen components and final evaluation of designed construction from the law standards viewpoint.
|
|
|
Design and Production of Clamps for Mandrels ISO 40
Tomešek, Viktor ; Kalivoda, Milan (referee) ; Sedlák, Josef (advisor)
Main aim of this bachelor’s thesis is to design and product clamp for mandrel ISO 40. This clamp will replace the other one, which is used in the milling workshop C2 on BUT Faculty of Mechanical Engineering. It will ensure easier and faster operator’s work during tool change. Also manufacturing process, selected material and cutting conditions are described in this thesis. Theory necessary for an understanding of the issues is stated in introductory section. In the final part, there is executed technical-economical evaluation with the overall costings associated with the production of the clamp for mandrel.
|
|
|
Roll bending technology
Hejna, Jaroslav ; Štroner, Marek (referee) ; Žák, Ladislav (advisor)
The paper deals with the research of sheet metal bending technology. This technology is suitable for producing both cylindrical and conical parts. First summarized technological and physical nature of the technology. Also important is the method of making cones using bending machines. Different types of machines are disassembled. From the smallest hand to the largest three-roll maschine. In the future, the two-cylinder machines are the most promising. They are especially suited to their variability and also because the component can be manufactured faster than any other machine.
|
|
|
Introducing the volume of solids using Cavalieri's principle
Fialová, Eliška ; Vondrová, Naďa (advisor) ; Janda, David (referee)
The aim of the thesis is to use a series of pedagogical experiments to introduce the volume of a pyramid, a cone and a sphere using Cavalieri's principle for pupils of the ninth year of primary school. First, the thesis characterizes the theories and approaches on the basis of which the experiment was built, such as the generic model theory and constructivism. The next part deals with the analysis of schoolbooks for the upper primary school and gymnasium, which are devoted to the introduction of the volumes of solids of pyramids, cones and spheres, and especially those schoolbooks which introduce the given volumes using the Cavalieri principle. The pedagogical experiment was preceded by a series of lessons focused on familiarizing pupils with given geometric solids and deriving calculations of their surfaces. This was followed by the introduction of the Cavalieri principle in the plane and also in space. In the practical part of the thesis, the tasks that were used in the pedagogical experiment are presented. The description of the course of the pedagogical experiment is supplemented by copies of the pupils' solutions. The conclusions are illustrated by the pupils' observations and summaries, which they arrived at in the form of a discussion on the tasks. At the end of the thesis, an evaluation of...
|
|
|
Semigroups of lattice points
Scholle, Marek ; Kepka, Tomáš (advisor) ; Šaroch, Jan (referee)
The thesis deals with subsemigroups of (Nm 0 , +), a special discussion is later devoted to the cases m = 1, m = 2 and m = 3. We prove that a subsemigroup of Nm 0 is finitely generated if and only if its generated cone is finitely generated (equivalently polyhedral) and we describe basic topological properties of such cones. We give a few examples illustrating that conditions sufficient for finite generation in N2 0 can not be easily trans- ferred to higher dimensions. We define the Hilbert basis and the related notion of Carathéodory's rank. Besides their basic properties we prove that Carathédory's rank of a subsemigroup of Nm 0 , m = 1, 2, 3, is less than or equal to m. A particular attention is devoted to the subsemigroups containing non-trivial subsemigroups of "subtractive" elements.
|
|
|
Conception of a conical splitter for wood
Stejskal, Jan ; Pokorný, Přemysl (referee) ; Hloušek, David (advisor)
This bachelor thesis consists of an introductory research part and a structural draft of a conical wood splitter with typed technical parameters and maximal log length and width. The thesis contains computing and strength examination of chosen components and final evaluation of designed construction from the law standards viewpoint.
|
|
|
Intersection of solids
Otrubová, Anna ; Hromadová, Jana (advisor) ; Šarounová, Alena (referee)
The four chapters of this diploma thesis introduce a survey of the basic intersection types of solids, the focus being placed on the intersection of two pyramid and prisma solids, acting as a counterweight to most textbooks' interest in intersection of curved surfaces. The first chapter provides a detailed, wide-ranging insight into the issue of the solid and line intersection. The conclusion part of the thesis provides the reader with a brief commentary on the used literature. The work is supplemented with figures and example solutions. In the appendix part are found pre-drawn assignments. The enclosed CD contains complementary materials such as step by step solutions and 3D models created in the GeoGebra software along with drawn problems found especially in upper secondary school geometry textbooks and curriculum.
|
|
|
Roll bending technology
Hejna, Jaroslav ; Štroner, Marek (referee) ; Žák, Ladislav (advisor)
The paper deals with the research of sheet metal bending technology. This technology is suitable for producing both cylindrical and conical parts. First summarized technological and physical nature of the technology. Also important is the method of making cones using bending machines. Different types of machines are disassembled. From the smallest hand to the largest three-roll maschine. In the future, the two-cylinder machines are the most promising. They are especially suited to their variability and also because the component can be manufactured faster than any other machine.
|
guest ::
