|
|
Analysis and Implementation of Virus Pattern Rules
Janeček, Jiří ; Schäfer, Jiří (referee) ; Janoušek, Vladimír (advisor)
This bachelor's thesis deals with analysis and implementation of rules for program, which routes virus samples for their later processing. The expert system is integrated in this program. It was created by using tool called CLIPS. This thesis also describes environment, where program is situated, and importance of component like this in system for virus sample processing. Analyzer has been implemented in C/C++ language.
|
|
|
Control and Diagnostic System for I2C Bus
Juhás, Miloš ; Šebesta, Jiří (referee) ; Urbanec, Tomáš (advisor)
The objective of this diploma thesis is design and realization of I2C bus analyzer. I2C bus protocol is briefly described, together with means of connecting devices to the bus. Next the basic requirements for I2C bus analyzer are defined. Then the design of hardware I2C-to-USB converter including block description is proposed. The chapter dedicated to converter firmware describes method of communication with PC, decoding of intercepted commands and principles of master, slave and passive mode of bus monitoring. The last part is focused on operation software and its structure. Described are individual interfaces, most notable classes and default plugin modules.
|
|
|
Breath Alcohol Tester
Pagáč, Patrik ; Kolář, Radim (referee) ; Chmelař, Milan (advisor)
The theme of bachlor’s project is design of simply breath alkohol tester. A breath alcohol test determines how much alcohol is in your blood by measuring the amount of alcohol in the air you breathe out (exhale).My task is interpret the possibility of measuring the alcohol content in the body. Describe the different methods and compare their accuracy and useability for practical measurements and also used in law enforcement.
|
|
|
Design of 10-channel audio equalizer with optimization of frequency characteristic and spectral audio analyzer
Štěrba, Václav ; Dvořák, Radek (referee) ; Šotner, Roman (advisor)
This work deals with the design of a 10-zones equalizer with optimized frequency characteristics with a spectrum audio analyzer. In this work the problem of processing audio signals using equalization for filtering the interference frequencies, correction of frequency cover signal boost or suppression of the required zones of the audible spectrum are also analyzed. The influence of subjective perception of sound intensity of the audio signals reproduction and its use in working with equalizer is discussed too. The work describes the principles and usage of the audio-analyzer as a tool for the optimization of the audio equalization setting when ensuring the appropriate listening conditions of music reproduction, spoken word, sounds, etc. It also focuses on the signal source for testing audio-chains, their generation and measurement using the audio analyzer. The equalizer equipment, audio-analyzer generator of reference signals equipment and power supply are designed as a single unit.
|
|
|
Packet analyser for a Wireless Sensor Networks based on the standard IEEE 802.15.4
Bednařík, Martin ; Šimek, Milan (referee) ; Mráz, Ľubomír (advisor)
The objective of this thesis is to get familiar with wireless sensor networks technologies and with standard IEEE 802.15.4. and communication principle in wireless sensor networks built on this standard. Main goal of this project is to design a packet analyzer, which is capable to catch data on chosen channel and this data is able to analyze. Part of this project is production of necessary microcontroller software equipment. Another output of this project is do a research of available packet analyzers on market and compare them with analyzer build by this thesis.
|
|
|
Analysis of LAN Network followed by Simulation in Opnet Modeler Environment
Skopal, Jakub ; Růčka, Lukáš (referee) ; Hošek, Jiří (advisor)
This thesis deals with the exploration of possibilities of LAN analysis with the use of the hardware analyzer Finisar TGHs from the Finisar Corporation Company. As a monitored network was choosed the local computer network in the laboratory PA-249 at the Department of Telecommunications, which is located at the Faculty of Electrical Engineering and Communication, Brno University of Technology. All results acquired from the complex long-term monitoring of the choosed LAN network are described in this thesis. Further, the thesis is focused on the simulation and analysis of the model of this network that was created in the simulation environment Opnet Modeler. The data obtained from the real LAN monitoring were used as a basis of an operating simulation of the transmission abilities and features of the real LAN network. The last part of the thesis describes the verification of the transmission capabilities and characteristics of the real LAN. Verification was performed in Opnet Modeler, where the network has been analyzed in detail.
|
|
|
Packet Analyser for Wireless Sensor Networks with Ethernet Interface
Leixner, Martin ; Šimek, Milan (referee) ; Mráz, Ľubomír (advisor)
The aim of this work is study the standard IEEE 802.15.4. Implement a packet analyzer for the frequency band 2.4GHz and sub-gigahertz band. The analyzer will provide accu- rate time stamp to the received packets. It will operate remotely and controlled by a web page. Implemented analyzer will work with the inspection software Wireshark. Finally, evaluate the parameters of the proposed packet analyzer.
|
|
|
Diagnosis of mechanical vibrations in asynchronous motor origin
Dostál, Martin ; Dostál, Lukáš (referee) ; Janda, Marcel (advisor)
Every machine needs to be maintained and controlled, if may work reliably during they service life. Big part of service life of expensive machines are those machines in operation. Vibration diagnostics is type of analysis, that doesn’t need removal of rotation machinery. The vibration, that are created by running machinery, are used as source of information about mode of operation. This master’s thesis contains theoretical analysis of vibration diagnostics and vibration measurements of a particular machine. This thesis contains 3D models of bearings and rotor asynchronous machine, which are created by software Autodesk Inventor 2014. Bearings vibration analysis of this models is performed by software Ansys Workbench.
|
|
|
Wirelles netowrok monitor
Slováček, Miroslav ; Fiedler, Petr (referee) ; Bradáč, Zdeněk (advisor)
This master´s thesis deal with designing of the system for ZigBee wireless network monitoring. In the first, treoretical part, is reader introduced to this wireless standard. Acquired informations are possible to compare with the simillar wireless standards. Next part of this document describes procedure of designing harward part of modular system - motherboard and scanning module. In this place is so discussion about component parameters, which are very needed to keep. One part of this discussion is about the problems with wrong component parameters. The last part of this master´s thesis is about software part of this project and so shows designed system in work.
|
|
|
Operational efficiency of gas boilers
Marčiš, Šimon ; Vyhlídalová, Karolína (referee) ; Počinková, Marcela (advisor)
This master’s thesis elaborates a design of water heating and heating system for a building of a rehabilitation center in Horný Hričov. The theoretical section describes operational efficiency of gas boilers and associated calculation methods. The experimental section covers measurements of condensing gas boiler at various temperatures of heating water conducted in university laboratory. Operational efficiency was then calculated using indirect method based on the measurement results. Subsequently, calculated values and values measured by an operational efficiency analyzer were compared. The comparison revealed minor deviations in operational efficiency values and different values of condensing heat utilization between the calculations and the analyzer results. The analytical section of the thesis consists of complex designs of two versions of the heating system and the water heating. The first design version uses condensing gas boilers as a heat source while the second version uses a water-air heat pump instead. The project section of the thesis is executed in the scope for a building permit and consists of a technical report and a design documentation.
|
guest ::
