|
|
Design and fabrication of a device controlling the important parameters of the aquarium based on the selected microcontroller
Cagáň, Adam ; Levek, Vladimír (referee) ; Háze, Jiří (advisor)
This master’s thesis describes design of the system, which automatically regulates water temperature in aquarium and measures water hardness. There is performed thermal analysis of specific model of aquarium, which defines required heat power. Based on this power Peltier module and heat exchangers are selected, that are part of designed heat pump. Thesis describes design of control unit based on ESP32-S3 microcontroller and complementary power supply circuit for Peltier module and uninterruptible power supply for microcontroller. Subsequently, there is designed web user interface running on Raspberry Pi 4B, which allows user to change desired water temperature, lighting interval and display measured water parameters.
|
|
|
Design of current sense comparators for automotive front lighting
Schilhab, Jan ; Prokop, Roman (referee) ; Kledrowetz, Vilém (advisor)
The diploma thesis deals with the problem of current sensing on integrated DC-DC converter switches using a comparator with reference current. Various current sensing methods are discussed in the thesis and a method of sensing current on a MOS switch using a smaller channel width reference transistor is thoroughly described. The paper also describes the basic properties of comparators and a suitable methodology for designing a fast comparator operating continuously in time. A major part of the thesis is devoted to the design of comparator blocks for current sensing at the top and bottom switches on the transistor level and presentation of the results obtained by simulations in Cadence Virtuoso environment. At the end, simulations are presented to verify the function of the designed blocks in a simplified buck DC-DC converter system.
|
|
| |
|
|
DC/DC converter 12 V to 300 V
Buba, Ondřej ; Kubíček, Michal (referee) ; Kolouch, Jaromír (advisor)
The thesis deals with design of switching power supply to power the oscilloscope. In this project the topology of the DC-DC converter is chosen, the pulse transformer and the output coil is designed. The control circuit is also choosen a suggested. This circuit will be replaced with microcontroler ATMEL in the second part of this thesis. The microcontroler will be programmed to replace the control circuit.
|
|
|
Backup power supply with solar cell
Hrubý, Michal ; Brančík, Lubomír (referee) ; Kubíček, Michal (advisor)
Due to the modern trends of energy production from renewable sources, this thesis deals with backup power powered solar cell. Analyzes the principle of operation of the solar cell, describes its technological development. Describes types of commercially available accumulators and their specific properties and the recommended charging. It then focuses on the description of the activities used DC-DC converters and their specifics. The aim of this work is to construct a backup power device that uses USB, independent of the electric distribution network.
|
|
|
Power supply system for mobile devices with high effiency
Vičar, Ondřej ; Kledrowetz, Vilém (referee) ; Brna, Jaroslav Rakušan, ENERGOKLASTR, Slavkov u (advisor)
This Master’s thesis is focused on design of voltage converter’s system operating with supply voltage of batteries. There are selected appropriate types of batteries, converter topologies and modes of their control. The specified output branches are systematically divided into three separate modules. Each module is designed in detail with focus on high efficiency. The modules are implemented and optimized. Parameter of final modules were measured and compared with correctness of design and theoretical assumptions.
|
|
|
Design of Power Supply for Aircraft Model
Šrámek, Martin ; Huzlík, Rostislav (referee) ; Hadaš, Zdeněk (advisor)
Diplomová práca, ktorú držíte v rukách, sa zaoberá návrhom elektrického generátoru pre modely lietadiel na diaľkové ovládanie poháňané spaľovacím motorom. Takýmto modelom je dodávaná energia pomocou batérií, ktoré sa musia po vybití vymieňať. Motiváciou tejto práce bolo potlačiť potrebu pristávania za účelom dobíjania batériových paketov. Práca vyvíja niekoľko analýz a simulačných modelov pre riešenie tohto problému.
|
|
|
Switching power supply for electron microscope
Jánešová, Daniela ; Szendiuch, Ivan (referee) ; Hejátková, Edita (advisor)
This thesis is about theory of switching power supplies and about a specific solution of switching power supply for electron microscope. In the beginning of the thesis are mentioned various solutions of part blocks of switching power supplies, their advanteges and disadvanteges, and their suitability for electron microscopy. In the next part of the thesis are described requirements and design scheme of switching power supply for scanning part of electron microscope. The thesis i also about technical solution and practical testing of the switching power supply and verification of its functions.
|
|
|
Pulse Generator for GPR
Martínek, Luděk ; Dušek, Martin (referee) ; Šebesta, Jiří (advisor)
This thesis deals with the question of ground penetrating radar. At first it considers the electromagnetic field and its mathematical description. Then it covers measurement of electromagnetic pulses and their processing of sub-surface ground penetrating radar. . In this thesis is also described the involvement of pulse generator with several transistors operating in avalanche breakdown. Individual transistors are compared in time domain. The received waveform is then selected the best transistor for the final generator. Then is proposed solution for the final pulse generator and its implementation. For impulsive generator is also designed and constructed increasing the DC-DC voltage converter. Finally, it is necessary to measure the time behavior of the output pulse generator.
|
|
|
Outdoor Robot Hardware Design
Sitta, Michal ; Veselý, Miloš (referee) ; Žalud, Luděk (advisor)
This work starts with slightly more detailed description of Ackerman and differential steering. Next shows parameters of direct-current brush and brush-less motors and gear-boxes uses in robotics. Electro technical part show problems of control direct-current brush motor, design of DC-DC converter with integrated circuit MC34063, reading information about steering angle with potentiometer and speed with optical encoder. In the end of work is shown simple byte oriented communication protocol used between microprocessor and desktop PC.
|
guest ::
