|
| |
|
| |
|
|
Design of special purpose tool for sag measurement
Mejzlík, Jiří ; Vetiška, Jan (referee) ; Houška, Pavel (advisor)
The aim of the thesis is to design a special purpose tool for sag measurement. Three possible solutions are proposed, for each the production cycle time is calculated and its approximate costs are estimated. The best solution in terms of a trade-off between both key quantities is suggested. Next part of the work deals with the selection of suitable drives for the manipulator as well as of the other components for the whole electrical device. Finally, a possible automated control of the complete machinery, including the electrical wiring diagram, is presented.
|
|
| |
|
|
Design methodology for the selection of basic components of linear machine tool axes
Král, Stanislav ; Dosedla, Michal (referee) ; Holub, Michal (advisor)
The aim of the thesis is based on specified parameters positioning units, which include stroke (1m, 2m, 4m), load (5kg, 50kg, 500kg), you place the position accuracy (0.04 mm) and dynamic (maximum attainable speed 1.5 m / s), proposals to build a ball screw, linear motor, a toothed belt and toothed comb. For selected variants of positioning units to design a 3D model of positioning units. The proposed variations to compare and define their advantages / disadvantages, techno-economic comparison, the limit values of individual designs, etc. The work includes a search drive in positioning units, design units with toothed belt, a toothed comb, ball screw linear actuator, a calculated message of individual proposals then 3D design options for the ball screw and linear motor including drawings and assembly drawings.
|
|
|
Electronic Unit for Data Acquisition of Vehicle Dynamic
Machač, Jakub ; Rasch, František (referee) ; Svída, David (advisor)
The diploma thesis is focused on design of an electronic unit for data acquisition of vehicle dynamics. It deals with not only design, but also with the testing and comparing to the other common used electronic units. It also includes proposition for choosing the measured quantities as well as their brief features and description of common used sensors to measure them.
|
|
|
Modelling of differential current amplifier
Polák, Josef ; Šotner, Roman (referee) ; Jeřábek, Jan (advisor)
The aim of my diploma thesis was programming of systems for measuring AC, DC and impedance measurements. Each measuring system measures selected characteristics of current amplifier with controllable amplification DACA_N. Control programs I have created in Agilent VEE Pro 9.2. The measured data are stored to executable files in MS Excel for further processing. With created measurement programs I made measurements of eight current amplifiers. The results of individual measurements I compiled into graphs and compared with each other circuit characteristics of amplifiers. Then there is described controlling and connection of current amplifier and its construction. At the end the diploma thesis describes amplifiers with the worst and the best measured circuit characteristics. The measured values show that the amplifier DACA_N with slight differences works by theoretical assumptions and measurement systems suggested by me work with no problem.
|
|
|
Structure and Use of the Measuring System for Research of Lubrication Device
Brhlík, Rostislav ; Omasta, Milan (referee) ; Nevrlý, Josef (advisor)
This work deals with an adaptation of the measuring system for the functional analysis of the lubricant divider. Within the new structural design, there were used manometers, flowmeters and dynamic scales to determine the properties of the lubrication system; data acquisition card and the appropriate software were designed too. The methodology of data measuring and analysis were also elaborated. The methodology is based on the experience from measuring, which was realized with the lubrication system OK - 02 from Tribotec Company. Finally, the cascade lubricant dividing system was designed. This is a newly designed flow divider with an innovative internal layout. The aim of the proposed measurement system is an optimization that will lead to effective dividing of lubricating mixture and applying the necessary amount of lubricant to wheel flange.
|
|
|
Position control of cross-table dedicated manufacturing machine
Plocek, Jaroslav ; Vetiška, Jan (referee) ; Houška, Pavel (advisor)
The bachelor thesis treats the drive solution of the two axis cross-table of a single-purpose manufacturing machine. The first chapter analyzes the concept of drives and compares different variants using either a direct linear drive or a ball screw with a rotary servo drive. The thesis further deals with sizing the motor and the power unit assembly and the description of the whole measuring system. The structure of cascading position controller, its description and the calculation of current and speed control loops is covered in the next part. The last section discusses practical settings of all control parameters.
|
|
|
Measuring system for analysis of pressure relations in spray lubrication device
Popelka, Michal ; Vaverka, Michal (referee) ; Nevrlý, Josef (advisor)
This thesis deals with the selection and design layout of the measuring system for the analysis of pressure and flow conditions in the lubricating system and a particular pressure and flow sensors. Sensors were selected according to suitability for use in these conditions of measurements (pressure, flow, etc.). Work also includes the review and selection of data bus for converting the output signal from the sensor to the evaluation unit (computer). It also includes selection of the measurement software to analyze the values arriving from the sensors into the measurement computer, find the optimal conditions for lubrication of wheel flanges of rolling stock.
|
guest ::
