|
|
Improvement Power Parameter of Small Induction Motors
Kuda, Roman ; Vítek, Ondřej (referee) ; Hájek, Vítězslav (advisor)
This master´s thesis treats of all asynchronous motor. The project is about type and distribution motors, about differences between three-phase and single-phase machines and efficiency. In one of the chapters describes a particular type of engine with all the parametersfrom the manufacturer. This engine is completely analyzed and it is measured in detail. Then the project deals with the division, the calculation of losses and subsequent possibilities to increase the efficiency of induction motor. In the last chapter is calculation of single-phase motors, based on the engine produced.
|
|
|
Device for stringing cable on a drum
Polách, Martin ; Pokorný, Jan (referee) ; Kašpárek, Jaroslav (advisor)
The thesis deals with the design of a cable spooling device on a spool drum under different modes of operation of winding. The focus is on the calculation and design part, where the calculations include the functional dimensions of the individual components and the force effects emanating from the load generated during winding. The design part includes the design of the individual components. Finally, an analysis of the selected structural nodes under different winding modes was performed. This work includes drawings containing the overall equipment assembly, subassembly of the weldment frame and shop drawings.
|
|
|
Design of a prototype table winder for linear coils
Ryza, Vojtěch ; Hrabčík, Miroslav (referee) ; Řehák, Kamil (advisor)
The diploma thesis deals with the design of a prototype table winder for linear coils. The first part of this work describes the basic properties of the coil and its winding methods. In the following section, a critical search was made of the reels available on the market based on which the reel concept itself was created. The work describes in detail the procedure of the winder design together with the design variants of the individual parts of the winders. At the end of the diploma thesis is presented the needed prototype of the coil winder. This problem was solved by using the 3D program SolidWorks and FEM in the program ANSYS Student. The project describes the individual steps of the design of the concept of a prototype linear winder and the component's design.
|
|
|
Solid State Tesla Coil
Pařenica, Jakub ; Mikláš, Ján (referee) ; Martiš, Jan (advisor)
The bachelor's thesis focuses on a theoretical description of the operation of Tesla's transformer, its design, including electronics, and its subsequent construction. The basic theory of the transformer replacement scheme is described. The Tesla transformer is generally described, as well as the methods of excitation of the primary side of the transformer, the generation of the discharge, the skin effect and the meaning of resonance. Furthermore, the work describes the construction of the primary coil holder, secondary coil. The work contains a pattern of the power board from the Eagle program, and everything is accompanied by photos. The work describes the recovery procedure and describes all the waveforms that were measured before and after the connection of the secondary coil.
|
|
| |
|
| |
|
| |
|
|
Losses reduction of single-phase induction motor
Vaško, Dávid ; Mach, Martin (referee) ; Vítek, Ondřej (advisor)
Bachelor thesis Losses reduction of single-phase induction motor deals with issues of increasing the efficiency of single-phase induction motor JMO90-4S-90 from EMP s.r.o. Slavkov near Brno. The first part deals with the theory of induction motors, especially single-phase motors and analysis of losses in induction machines. The second part deals with the introduction of motor solutions and methods used for loss reduction. In the third part, the thesis deals with the calculating selected parameters, the design of motors in RMxprt, and their modification for improving efficiency. The fourth part deals briefly with the design of motors in Ansys Maxwell, comparison of results obtained from Maxwell and RMxprt with the results from measurement for motor JMO90-4S-90 and comparison of results from Maxwell and RMxprt for other motor solutions.
|
|
|
Design of oil distribution transformer
Mrajca, Miroslav ; Mach, Martin (referee) ; Ondrůšek, Čestmír (advisor)
This master thesis deals with the manufacturing process of oil distribution transformers. Firstly, the thesis devotes to the design arrangement of the magnetic circuit and its manufacturing technology. The procedure of cutting laminations for core and their building into the core. Subsequently, the thesis describes technologies used for manufacturing primary and secondary windings including procedures on winding machines. Then it deals with the production of the tank and the final assembly of the transformer into one unit. The next part of the thesis discusses the design procedure of the assigned distribution oil transformer with a numerical calculation while respecting the requirements of the standards. Finally, the costs of the material of the designed transformer are determined.
|
|
|
Impact of winding on induction machine characteristics
Mikmek, Vladislav ; Janda, Marcel (referee) ; Mach, Martin (advisor)
This thesis deals with the analysis of a three-phase winding of an induction engine. After the theoretical introduction concerning different types of windings, two types of their analysis and the importance of the winding factor, two methods of analysis and design tools are explained: Görges diagram and Tingley scheme. This scheme is then used for the design of all possible variants of winding for a certain number of stator slots and the theoretical shape of magnetic field is analysed. The next step is a deeper software analysis of the engines with variants of windings with different coil pitches and number of conductors per slot. Especially the finite element method is used in this part. The obtained values and their characteristics of the simulated engines are compared numerically and graphically. Then the changes of important values for different windings are described. The optimal winding according to chosen requirements is chosen.
|
guest ::
