|
|
Control Unit for Humanoid Robot
Florián, Tomáš ; Kopečný, Lukáš (referee) ; Žalud, Luděk (advisor)
The main goal of this project is to understand broadband sold Robonova-I humanoid robot and to design new improvements. The thesis is divided into five main chapters: The first of them (Robonova-I) is concerning the kit of Robonova-I, its completion and control possibilities. In details it deals with used servo motors, their operating and compares them. The next chapter is concerning the design of the control unit along with description of architecture of the processor and control possibilities with demonstrational board. In third there is a software solution of particular methods and commands which control the unit with demonstrational board. Chapter “The Design of Printed Circuit Board” describes facilities of the designed printed circuit board. The last chapter describes the final program for robot control through the use of computer and some of the algorithms by means of which the robot controls the microprocessor.
|
|
|
Position control of servo with discontinuouns rechangeable speed
Jindra, Pavel ; Věchet, Stanislav (referee) ; Němec, Zdeněk (advisor)
Diploma thesis work includes simulation of compensation of control for discrete. The aim of the work is a solution positioning control of servomotor drive piston, which is controlled by pass of the pressure oil with the help of several electromagnetically controlled switchboards with the orifice in the output channels. The verification activities of the regulated system is done using simulation in Matlab/Simulink and Matlab/Simulink, Matlab/Hydrosim. The requirement on the created model is to verify the behavior of the system to be modified to be used for the further development of the issue
|
|
|
System with Model Servos
Jablonický, Jaroslav ; Maršík, Lukáš (referee) ; Zemčík, Pavel (advisor)
This work is focused on exploring how to control modeling servos by computers. It will also serve as an overview or a guide for beginners. The work includes the design of a simple robot, more precisely it is a simple robotic hand, but in particular it contains control designs from different platforms using different means. Finally, there are recommendations for each platform.
|
|
| |
|
|
Table tennis robot
Nguyen, Thuc Tuyen ; Věchet, Stanislav (referee) ; Marada, Tomáš (advisor)
This diploma thesis deals with designing and manipulating a robot for training table tennis. Robot's mechanical construction is based on aluminium profiles supported by various standardized assembly units, such as rotating bearings, plain bearings, threaded rods... The front-end part of the robot, which requires better deformation property and lighter weight, was made from ABS material using 3D rapid prototyping technology. The design of the robot allows its body to rotate around three axises. Thanks to the high dynamical ability, robot can be set to throw balls to various places on the playing table, with different types of ball spin. Balls will be shot out by two rubber wheels, which are attached to two electrical DC motors. By driving the speed of the two motors, we can control the speed of the ball, as well as speed of its spin. All robot's activities are driven by an embedded system designed using microcontroller ATMega128. A firmware for controlling robot's function was writen and flashed into the microcontroller. End-users might communicate with the robot via a system of buttons and a text LCD display. The built robot was tested and it has shown its ability to throw balls to 6 different places of the playing table, at different speeds, with different types of ball spin, and different spin speed, according to the parameters set by user.
|
|
| |
|
|
Servomotor with electronic commutating and his control and adjusting.
Schmied, Miloš ; Chomát, Luděk (referee) ; Pivoňka, Petr (advisor)
This thesis deals with the analysis of the actuator ACOPOS and its accessories. There are described the cascaded control loop concept and the setting servomechanism from B&R Automation with the important parameters. We follow the draft a speed controller servomotor with a load with the regards to knowledge of the control system. We compare the different methods of labor control actuator at last. There are implemented laboratory tasks of Position servomechanism and speed servo controller-on-load as a demonstration of our achieved results.
|
|
|
Two legged walking robot
Kraus, Václav ; Háze, Jiří (referee) ; Šteffan, Pavel (advisor)
The aim of this work is to present the topic of walking robots, the design and construction of a two-legged wirelessly controled robot. The work is divided into two parts. The first one is theoretical. It addresses the possibilities of sensorics and wireless communication technologies, which are used in robotics. The second part includes the robot's design of construction, walking and electronics. The output of this work is the robot construction, which is controled using a computer application via wireless technology WiFi.
|
|
|
Roboarm Controlled by FITkit
Říha, Lukáš ; Šimek, Václav (referee) ; Růžička, Richard (advisor)
The terms robotics and roboarms have a huge meaning in the today's world. This thesis describes the simple roboarm ROB1-3 control by the help of FITkit. FITkit has two main parts which are used for control - the microcontroller and the FPGA chip. The controlling of the roboarm is possible by the keyboard of FITkit or by the terminal. The motion is enabled by three servos Hitec HS-311. The servos are controlled by PWM signal which is generated by microcontroller of the FITkit.
|
|
|
Robotic hand controll using virtual reality
Sláma, Pavel ; Bílek, Michal (referee) ; Vyroubal, Petr (advisor)
This bachelor thesis deals with possible solution of controlling robotic hand with virtual reality. To realize this work is used a prosthetic hand from the InMoov project. This thesis describes basic principles of 3D print technology and deals with materials suitable for manufacturing of a chosen robotic hand. As next describes function and controlling of servos, hand control using prototyping platform Arduino communicating with the computer with MyRobotLab software support. To capture movement is used motion sensor for virtual reality Leap Motion.
|
guest ::
