|
|
Design of end effector for testing the defects in plastic bottles
Karn, Pavel ; Szabari, Mikuláš (referee) ; Kočiš, Petr (advisor)
This diploma thesis deals with the design of an end effector for robot that will be able to test the presence of defects in plastic bottles during their handling. The first part of the thesis is devoted to theory and deals with the different types of defects in plastic bottles as well as the currently used technologies for defect detection. The second part is focused on the systematic analysis and design of the variants, from which the most suitable one was selected using multicriteria analysis. The following part deals with the actual design of the selected variant and the necessary engineering calculations. The last part is devoted to the estimation of costing and the creation of manufacturing drawings.
|
|
|
Analyses of the Compressed Air Energy Storage proces in Ansys Fluent system
Hájková, Věra ; Šabacká, Pavla (referee) ; Maxa, Jiří (advisor)
This bachelor thesis discusses different types of energy storage in the introduction. It describes the different technologies, their functions, advantages and disadvantages. It compares them on the basis of the ESOI ratio, which is the ratio of energy stored on invested. The main type of energy storage covered in the term paper is compressed air energy storage. The thesis describes the principle of a method of energy storage as well the companies and projects that are working on or using this technology. Furthermore, the issue of heat energy loss during air compression is outlined, which leads to a significant reduction in efficiency. The last part of the thesis is a practical part, which uses a model example to show the temperature and pressure evolution during the pumping of air into the storage tank.
|
|
|
Increasing the range of a vehicle with alternative propulsion
Dryml, Tomáš ; Ranuša, Matúš (referee) ; Navrátil, Václav (advisor)
The bachelor's thesis deals with increasing the range of a vehicle with an alternative drive, which is compressed air. First, an analysis of the pneumatic circuit is performed, from which the areas to be modified result. To improve, it is chosen to find a suitable working pressure and the correct filling, which is calculated on the basis of constant pressure filling and subsequent adiabatic gas expansion. From the theoretical calculation, the runs per cylinder stroke at different pressures are determined and the selected pressures are subsequently experimentally verified. The results show that the most suitable setting increased the range from 331 meters using the original setting, to 616 meters with the new setting.
|
|
|
Accumulation of electricity for a source with unstable production
Petrenec, Jan ; Milčák, Pavel (referee) ; Pospíšil, Jiří (advisor)
This diploma thesis deals with possibilities of accumulation of electricity generated by renewable sources with unstable production. Several goals were set by an assignment of this thesis. Within a research, current trends of the accumulation are presented in detail on examples of specific representatives with their technical parameters and economic possibilities. Further, an unstable source of electricity – the wind farm of three power plants Multibrid 5000 with all its parameters and operational details is defined for purposes of individual designs of accumulation systems. Firstly, the detailed design of an advanced compressed air energy storage (A-CAES) is realized. It includes a thermodynamic calculation of chosen components, their partial technical solutions, a financial evaluation of investment and a determination of theoretical payback period. Furthermore, the design for accumulators Tesla Powerpack is realized. It contains a calculation of individual system parameters, a financial evaluation of investment and a determination of theoretical payback period. Last part of the thesis is dedicated to a comparison and an evaluation of the achieved results of both realized methods of the electricity accumulation. In the end, A-CAES is chosen as more perspective variation.
|
|
|
Optimization of ultrasonic leak detector of pneumatic system
Macků, Ondřej ; Mazal, Pavel (referee) ; Vlašic, František (advisor)
The thesis deals with design and optimization of exchangeable modules for localization of air distributable ultrasound in concept of ultrasound probe design. Several series of these modules were manufactured using the technology of rapid prototyping and tested on artificially created source of air leak. Based on these verification experiments two types covering wide use for identification of pneumatic systems leaks were selected and modified. These two types are long range module for more accurate and expended reach of the leak detection and focusing attachment for narrowing the received range of scanning module and elimination of surrounding ultrasound. Part of the thesis is also analysis of the acoustic signal processed by modern acoustic emission analysers which allow besides standard parameters recording also continuous sampling up to 10 MHz and design solution for attachment of add-on modules to the detector. The thesis is beneficial for raising awareness of leak measurements, prototype manufacturing by using the 3D printing and designing and manufacturing of modules.
|
|
|
Intercooler for the CDS SEMI-PRO combustion engine
Novozámský, Richard ; Bazala, Jiří (referee) ; Svída, David (advisor)
This diplom thesis describes design of new pressured air cooling system for trubocharged Diesel engine used in CDS Semi-Pro competitions. First part is focused on analysis external conditions influencing the desing. Second part pays attention to simulations of performance. Third part describes design of two systems and possible testitng method. In last part, the real parametrs are put into the computing model followed by verification of the results and evaulation of the designed systems.
|
|
|
Use of compressed air energy storage
Laca, Theodore Nicolas ; Charvát, Pavel (referee) ; Štětina, Josef (advisor)
In the search part is elaborated a basic overview of the importance and benefits of electricity storage. It describes the main possibilities of electricity storage, divided by the form of storage. It includes knowledge of thermodynamics in compression and expansion of ideal gas (air). It briefly describes practical applications of compressed air. Further, it focuses on compressed air energy storage (CAES). It contains a basic simulation of the compressed air engine. The conclusion deals mainly with the prospects of using CAES.
|
|
|
Analysis and optimalization of pneumatic system of race pneumobile
Navrátil, Lukáš ; Nevrlý, Josef (referee) ; Ranuša, Matúš (advisor)
This thesis deals with the theoretical design of the new pneumatic system, which should lead to increased performance and fuel racing pneumobilu Blowfish. After the theoretical proposal deals with the analysis of both the new pneumatic circuit, and the old pneumatic circuit. The culmination of this work will be participating in the competition with the pneumobil in Hungary, Eger. The first part describes the current state pneumobilu contest and its rules. Further there are described in detail pneumatic elements that are used to pneumobilu. In the second part contains measurements that verify the effectiveness of the new pneumatic circuit.
|
|
|
Regulation options of renewable energy sources
Pavlíček, Jiří ; Morávek, Jan (referee) ; Pěcha, Jiří (advisor)
This bachelor's thesis deals with the regulation of renewable energy sources. It focuses on ways of managing and possibilities of regulation renewable energy resources. Indicates the proportion of various types of renewable energy sources in electricity production and their representation in the electrical load profile. Thesis describes the various storage systems, which can be used to stabilize the renewable energy sources. Evaluate the applicability of these storage systems in the energy sector.
|
|
|
Development of pressure switch for rail vehicles
Havelka, Ondřej ; Tůma, Jiří (referee) ; Tůma, Zdeněk (advisor)
This diploma thesis deals with the design of pneumatic pressure switch with adjustable hysteresis. In the thesis is carried out the introduction in the theory of compressed air and research of the pressure switches at the market. Based on the gathered information and customer specification, the design draft of the pressure switch has been created. In the thesis are described three main parts of the prototype: transform of the pressure, adjustable hysteresis and synchronization of the microswitches. In the end of the thesis is described the testing of prototype and summary of the results.
|
guest ::
