|
|
Sintering of advanced ceramic materials
Průdek, Miloš ; Trunec, Martin (referee) ; Maca, Karel (advisor)
V předložené diplomové práci bylo studováno slinování hexagonálního Al2O3 a kubického MgAl2O4 pomocí slinovacích cyklů složených z beztlakého předslinutí metodou dvojstupňového slinování s následným doslinutím s využitím tlaku (HIPováním). Cílem bylo pokusit se snížit (při zachování vysoké dosažené hustoty) střední velikost zrn a tím zvýšit tvrdost keramiky popř. optickou transparenci. Hlavní úsilí bylo věnováno optimalizaci předslinutí pomocí různých slinovacích cyklů. Přestože bylo vyzkoušeno velké množství různých kombinací teplot a prodlev dvojstupňového slinování, nepodařilo se výrazným způsobem zvýšit výslednou tvrdost vzorků. V případě kubického MgAl2O4 bylo dosaženo hustot blížících se teoretické hustotě, což se projevilo v optické transparentnosti vzorků.
|
|
|
Preparatin of dopped lead-free piezoceramic materials by non-conventional sintering methods
Žaludek, Jakub ; Kachlík, Martin (referee) ; Pouchlý, Václav (advisor)
Piezoceramics BaTiO3 doped with ZrO2 was studied in this thesis. Six different compositions were prepared from base powders of BaTiO3 and ZrO2. with 10, 20, 40, 60, 80 and 90 wt% ZrO2. These mixtures were sintered using convetional sintering method and by Spark Plasma Sintering. Resuting ceramic compacts were subjected to measuring of density, dielectric constant, permitivity, polarization P-E curves, piezoelekctric faktor, loss factor and dilatometric measurements. From these results can be said that i tis possible to create piezoceramic BaTiO3 doped by ZrO2 with relative density higher than 94 %t.d. and these ceramics can possess piezoelectric properties. Value of highest piezoelectrick factor 33=9 / was achieved with addition of 20 wt% ZrO2. Dilatometric measurements discovered effect of increasing ammount of ZrO2 in BaTiO3. Rising amount of ZrO2 had a lowering effect on initial sintering temperature and materials achieved higher relative densities. This was also true for samples sintered using SPS, where it was less obvious. Measuring of electrical properties discoverad electric conductivity for SPS sintered samples, which was most probably caused by carbon introduced into samples during SPS cycle.
|
|
|
Influence of low-temperature plasma on enhaced ceramic processing
Rolek, Ondřej ; Kachlík, Martin (referee) ; Pouchlý, Václav (advisor)
This masters’s thesis contains literary research about basic shaping methods of ceramic materials concerning the slip casting method. In addition, stabilization of ceramic slips, drying of ceramic green bodies and their subsequent sintering are described. This thesis also includes a description of plasma technology, including DCBD (Diffuse Coplanar Barrier Discharge) technology. In experimental part of this thesis the Al2O3 powder was treated with DCBD technology. From the prepared powder, the green body was prepared by the slip casting method, which was subsequently sintered by one-step and two-step sintering. The thesis describes the methods of preparation of ceramic samples and their evaluation. Evaluated experiments have shown that plasma technology has a positive effect on the treatment of ceramic powder Al2O3. Alumina ceramic samples of high relative density ( 99%) and low grain size (
|
|
|
Processing of alloy 2618 using selective laser melting technology
Dokoupil, Filip ; Hutař, Pavel (referee) ; Paloušek, David (advisor)
This diploma thesis deals with finding and verification of appropriate technological parameters of SLM technology for the processing of aluminum alloy 2618. In the theoretical part, an introduction to additive manufacturing of aluminum alloys and general description of processes occurring during SLM production is given. Based on general knowledge were designed different types of testing samples produced by sintering the metallurgical powder using 400 W ytterbium fiber laser, which so far in the literature for aluminum alloy 2618 were not described. As the result, the technological parameters dependence on relative density and the detailed overview of the 2618 alloy processing by SLM technology is determined.
|
|
|
Synthesis and characterization of sulfurized polymers for electrochemical power sources
Svoboda, Lukáš ; Kazda, Tomáš (referee) ; Čech, Ondřej (advisor)
Batteries based on lithium-sulfur technology have the potential to increase the amount of stored energy in comparison with current lithium-ion systems while maintaining the same weight. Achieving this goal is possible due to the high theoretical energy density of sulfur, which exceeds the values of other materials used in batteries. However, these batteries suffer from several failing, which still hinder the practical use. The use of amorphous sulfur instead of its crystalline form might lead to increasing of durability and charge efficiency. Inverse vulcanization of sulfur seems to be the perspective method for the preparation of polymer sulfur because it prevents its recrystallization and stabilizes amorphous sulfur. The aim of this thesis is the preparation and study of properties of materials made of inverse vulcanized sulfur.
|
|
|
Study of sterilization effect of dielectric barrier discharge on procaryotic microorganisms
Bittnerová, Zuzana ; Ing.Hana Grossmannová, Ph.D. (referee) ; Kozáková, Zdenka (advisor)
Presented bachelor thesis is focused on sterilization effect of dielectric barrier discharge on procaryotic microorganisms. Sterilization is important biomedical and food-industry application and plasma sterilization is one of the method, which are suitable for sterilization of heat and chemical sensitive materials. Biologicaly contaminated samples were treated in dielectric barrier discharge operated at atmospheric pressure. The discharge was generated in argon and in nitrogen. Gram positive bacteria Bacillus subtilis was used as a bioindicator. Bacteria was spread onto the surface of paper and PET material. Efficiency of sterilization was evaluated according to exposure time, plasma power density and process gas. The positive effect of DBD on inactivation of microorganism was observed. The efficiency of the plasma sterilization increases with increasing treatment time. As regards plasma power density, the higher density was used the more effective the sterilization was and time necessary for inactivation of all microorganisms was shorter. Sterility was observed within 60 s while using plasma power density 2,37 W/cm, when using plasma power density of 1,78 W/cm longer treatment time is neccesary. The sterilization was more effective if argon was used as a process gas. Time necessary for the most reduction of microorganisms in argon was 10 s, while using nitrogen the reduction was only 50 %.
|
|
|
Non-conventional sintering of advanced ceramic materials
Suchý, Václav ; Kachlík, Martin (referee) ; Pouchlý, Václav (advisor)
This bachelors thesis deals with non-conventional sintering methods of advanced ceramic powders. The theoretical research on the topic of sintering and ceramics materials was done in the first part of this work. The end of theoretical section is devoted to the non-conventiolan sintering methods of ceramic powders. Experiments of sintering ceramic powders (cubic ZrO2 doped by 3mol% Y2O3) enhanced by electromagnetic field were made in practical part of this work. Specifically the method of Flash sintering was used. Results confirmed that it is possible to use Flash sintering method for making advanced ceramics. The material made by this technique had relative density of 95,9% and grain size of 0,22m.
|
|
|
Analysis of Data on Social Networks Based on Data Mining
Fešar, Marek ; Burget, Radek (referee) ; Bartík, Vladimír (advisor)
The thesis presents general principles of data mining and it also focuses on specific needs of social networks. Certain social networks, chosen with respect to popularity and availability to Czech users, are discussed from various points of view. The benefits and drawbacks of each are also mentioned. Afterwards, one suitable API is selected for futher analysis. The project explains harvesting data via Twitter API and the process of mining of data from this particular network. Design of a mining algorithm inspired by density based clustering methods is described. The implementation is explained in its own chapter, preceded by thorough explanation of MVC architectural pattern. In the end some examples of usage of gathered knowledge are shown as well as possibility of future extensions.
|
|
|
Microscopy of Time Variable Biologic Objects
Uhlířová, Hana ; Kozubek, Michal (referee) ; Peychl,, Jan (referee) ; Chmelík, Radim (advisor)
The subject of the PhD thesis is the application of a transmission digital holographic microscope (DHM) which was designed and constructed in the Laboratory of optical microscopy at the IPE BUT for the research of live cells dynamics. First part of the work is concerned with theoretical description of the microscope imaging properties dependent on the coherence of illumination. It is supplemented with experiments of imaging of a model and a real biological specimen. The following part describes construction modifications and innovations of the microscope and its equipment that enabled the utilization of the microscope for live cells observations. In the experimental part the methodology of live cells preparation and DHM imaging was worked out. The methodology was verified by the observation of cell dynamics during an apoptosis induced by the cytostaticum cis-platinum. Further experiments examined the dynamics of live cells in standard conditions and during a deprivation stimulus. A novel method of holographically reconstructed phase, named \uva{dynamic phase differences}, was set up to evaluate quantitative changes of cell mass distribution during the experiments. Depending on the degree of malignancy and density of cell outgrowth, various schemes of cancer cells behaviour during a specific reaction were revealed using this method. For the quantitative analysis of the DHM phase imaging, a suitable statistical characteristic and an interpretation of the measured data were proposed. Both of them were successfully applied for the comparison of cell motility of two cell types: parental and progeny cell lines. On the basis of the proposed processing, hypotheses describing the reaction mechanism of tumour cells to stress life conditions were established. In the conclusions we summarize our findings and suggestions for the construction and the applications of a new generation of the transmission DHM.
|
|
|
Modeling of Surface-Plasmon Propagation in Graphene
Hrtoň, Martin ; Munzar,, Dominik (referee) ; Kalousek, Radek (advisor)
The diploma thesis provides an introduction to electronic and optical properties of graphene, emphasizing thier tunability through the ambipolar field effect. Furthermore, an experiment, which would demonstrate the possible utilization of graphene in active plasmonics, is presented. The author focuses on light scattering simulations involving hybrid plasmonic structures made of noble metals and graphene. The scattering properties of those structures and their dependence on the density of free charge carriers in graphene are investigated. The author concludes that the proposed tuning of the response of a single metallic antenna through the electrostatic doping of graphene proves to be inefficient, and a more elaborate configuration will be required to enhance the effect and achieve the desired control.
|
guest ::
