|
|
Sports car for people with disabilities
Lopušek, Dávid ; Růžička, Bronislav (referee) ; Brandejs, Jan (advisor)
The master thesis deals with the engineering design and realization of a sports electric vehicle for disabled people. The first part of thesis summarize competitive vehicles on market and also the necessary theoretical knowledge for the design phase. After analyzing the research and determine the resulting vehicle concept follows the draft design. In this section based on calculations was chosen the solutions and necessary components for a vehicle. The following section describes the structure of the vehicle in implementing selected components. In conclusion, the evaluation of the proposed solution.
|
|
|
Effect of engine load on the output parameters of the tractor kits
Paulmichl, Roman ; Svída, David (referee) ; Bauer, František (advisor)
The thesis deals with the current situation in the construction of tractors, particularly engines and accessories. The work includes a methodology for measuring tractor rigs in traffic as well as methodology for plough/plow kits measuring. The measured values were tabulated, graphically presented and analysed. The thesis provides an overview of the issue of the combustion engine load placed on the engine by working conditions in transport, during primary soil tillage with different modes of operation of the tractor set. The thesis aim is to find out the practical effect of the engine load on the monitored parameters and to indicate possibilities for achieving higher efficiency in tractor units with minimum fuel performance
|
|
|
High-speed Steam Turbine
Albrecht, Jan ; Škorpík, Jiří (referee) ; Fiedler, Jan (advisor)
Main aim of presented master thesis is focused on construction of high speed steam turbine. Steam turbine is designed based on parameters of waste incineration plant in Brno. First chapters shortly summarized historical development, transformation process and work principal of steam turbine. Consequently on first captures is in depth described impulse and reaction blading including expansion in i-s diagram and basic equations for efficiency calculations. In major part of master thesis is firstly discussed conceptual possibilities of turbine application for given parameters. Based on chosen concept is compiled algorithm for thermodynamic calculation for each turbine module. Simplify calculation of gearbox is included as well. Based on calculations are compiled construction drawings of all parts of steam turbine.
|
|
|
Steam turbine
Skoupý, Pavel ; Ing.Duda (referee) ; Fiedler, Jan (advisor)
The master´s thesis concentrates on a project of steam turbine with controlled extraction points destined for a communal waste incineration plant. First, there the history of devices using steam as a moving medium is introduced and than follows the description of computing program, where the calculation was running. The master´s thesis subject consists in the thermodynamic project of turbine vaning, in basic project of gearbox including the check calculations and in technical economic comparison of single shaft and twin shaft constructional design. The design documentation is worked up according to the calculated outcomes and contains longitudinal section of turbine and dispositional turbine and gearbox settlement.
|
|
|
Project of worm gear for lift mechanism
Otisk, Jan ; Malach, František (referee) ; Malášek, Jiří (advisor)
This graduation thesis dwells on a worm gear design for an elevator mechanism in an already existing wheel case with actuator unit S3 for elevator type BOV 320/0,63. The work includes dimensional and control calculation for the worm gear and as an attachment you will find spiral worm and worm gear drawing documentation, including its specific location.
|
|
|
Steam turbine with ejector
Slezáková, Iveta ; Ing.Drahomír Maša (referee) ; Fiedler, Jan (advisor)
The main Target of this diploma is to find some reconciliation with cooperation of turbine and ejector. This work is containing informations about this mechanisms and also its historical development. The merits of this diploma thesis is thermodynamics calculation and proposal of main parameters and proportions of the turbine and the ejector. After this it is follow by the calculation of whole system of the turbine and ejector in consequence with calculation of turbine with by-pass regulation and also comparison of power output with ejector and with by-pass technology.
|
|
|
Traffic characteristics of 2+1 arrangement
Kabeš, Luboš ; Čepil, Jiří (referee) ; Radimský, Michal (advisor)
The thesis discusses the roads in lanes 2 + 1 arrangement in the country and abroad. It focuses primarily analogy of this type of arrangement in our situation, ie on stretches of roads I. classes with an increased number of lanes for slow vehicles to climb. Part of this work is to verify some of the traffic, including traffic flow characteristics compared to conventional two-lane roads, especially in terms of: sectional speed; overtaking; Accident and dependence longitudinal gradient. The work aims to evaluate the foreign experience and achievements of domestic communications options for application configuration 2 + 1 in the Czech Republic.
|
|
|
Selected ČSN Road Design Elements Optimization
Stránský, Jakub ; Čepil, Jiří (referee) ; Kosňovský, Michal (advisor)
The master‘s thesis focuses on the optimization of the design values of curves of the horizontal alignments of the roads. It deals with the comparison of values between czech and foreign standards and differences between them. The practical part examines the values of the real speeds of vehicles passing through the curves of various parameters that were measured during measurements of selected curves during 2014. From these data a new design values are derived that could be used for the design of horizontal alignments.
|
|
|
Analysis of the acoustic signal to detect the speed of vehicles
Koníčková, Tereza ; Beneš, Petr (referee) ; Klusáček, Stanislav (advisor)
The aim of this Bachelor thesis is to create software for sound signal analysis of a passing car with the aim to determine the driving speed. This work describes single methods of a car velocity measurement and it is submitting a new method of velocity measurement with using the Doppler principle at sound signal analysis. My work proved, that it is possible to use this method to determine the speed of vehicles.
|
|
|
Automotive Alternator Innovation
Volek, Martin ; Hýsek, Roman (referee) ; Hájek, Vítězslav (advisor)
The work deals with the analytical electromagnetic design of automotive claw-pole alternator 14V/120A. This design is verified in program Maxwell with a RMxprt tool. The results of both calculations are compared. Designed alternator is also compared with the results measured in the laboratory on the alternators of similar type. Furthermore, there are analyzed individual power losses of machine and listed options of reducing these losses, which results in an increase in overall efficiency.
|
guest ::
