|
|
The analysis of frame synchronous generator
Marada, Ondřej ; Střelková, Radka (referee) ; Pokorný, Přemysl (advisor)
The thesis is focused on the examination of the utility of a synchronous generator of a small hydroelectric power station in the case of a change of working position of the machine. The utility will be measured on the basis of the examination of deformations and state of stress of the frame of the generator for the present running (with vertical axis of rotation of the generator) and subsequently for modified running (with horizontal axis of rotation). This will be accomplished partly on the static shell model by finite element method and consequently on the simplified dynamic model.
|
|
|
Con Rod design and optimization of racing engine
Ulman, Jaroslav ; Zháňal, Lubor (referee) ; Beran, Martin (advisor)
This master thesis describes the design and optimization of connecting rod motor racing car. At the beginning of the whole work is a 3D-model of rods, from which then the whole work is based. Then it analyzes the current model of stress and on the basis of the results are made structural changes to the solution of rods. Newly adapted connecting rod is again analyzed using FEM and newly obtained results are compared with results of the original model of connecting rods. The conclusion deals with sensitivity analysis of selected parameters of rods and their potential effect on the resulting changes in strength connecting rod .Then is an assessment of all results.
|
|
|
Lower limb prosthetics FEM analysis
Omasta, Milan ; Náhlík, Luboš (referee) ; Paloušek, David (advisor)
This masters´s thesis deals with computational modeling of transtibial lower-limb prosthesis. For assesment of loading character and geometrical configuration, the gait analysis of an amputee, including ground reaction force measurement, strain gauge analysis and motion analysis, was accomplished. Information on geometry was obtained using 3D optical scanning procedure. Material model was gathered using non-destructive mechanical testing and mimicked in a FEA software. For loading conditions the static structure analysys using FEM was accomplished. The critical poins in construction was found. Recognition of agreement about experimental and computational model was accomplished.
|
|
|
High loading shovel
Petro, Roman ; Lžičař, Roman (referee) ; Škopán, Miroslav (advisor)
This diploma thesis solves construction project high dumping shovel for back hoe loader New Holland B100 and B110. There are described operating conditions in the introduction, transport material and technical parameters for back hoe loader B100, B110. There are mentioned possible construction’s solutions and own design. Follow the kinematics analysis of material’s dumping and the static analysis on shovel and frame. This is connected with following peg’s control and the solidity analysis of shovel and frame for different load cases, where the MFE was used
|
|
|
CFD geometry optimalisation of heat exchanger
Stromský, Ondřej ; Gottvald, Jakub (referee) ; Nekvasil, Richard (advisor)
The main task of thesis is to find optimum geometry of the heat exchanger. The biggest emphases is placed to finding the most optimum of streaming liquid in the heat exchanger and to minimisation pressure losses. There is a effort to regulate the streaming liquids in heat exchangers so that in multitube and on the shell side don´t create dead areas, it means to avoid sedimentation of particle in these places. Dead areas cause rising resistance against heat transfer and necessity of frequently cleaning the heat exchanger. For these reasons is necessary to do analyse of flowing and to looking for the optimal geometry of the heat exchanger.
|
|
|
Strain, stress and strength analysis of the high pressure compound vessel by finite element method
Koutský, Jiří ; Suchánek, Miroslav (referee) ; Vrbka, Jan (advisor)
Strength and strain analysis of high pressure compound vessel, which is used to produce superhard materials (for example synthetic diamond). This work was elaborated to compare the stresses and strains calculated by Prof. Jan Vrbka making use of the FEM program ‘Prokop’17 years ago with those gained with the contemporary FEM Ansys program. The vessel is loaded by internal pressure of size 6 GPa. The elastic-plastic material be-haviour is taken into account. Real value of friction between rings and non-uniform temperature field is included into the calculation. The process of assembling the compound vessel is simulated step by step.
|
|
|
Stress analysis of the tree root of an aircraft engine turbine wheel
Čepica, Vojtěch ; Svoboda, Miroslav (referee) ; Chromek, Lukáš (advisor)
The main focus of the bachelor thesis is stress analysis of the tree root of an aircraft engine turbine wheel. First part is dedicated to the issue of aircraft engine and various kinds of mounting the rotor blades. Next chapters of the thesis involve the calculation itself. The known equatations have been used in case of analytical calculation whereas the ANSYS Workbench program based on final element method has been used for the numerical calculations. Finally I compared both approaches in conclusion of the thesis.
|
|
|
Design of the supporting frame of lift cage
Zapletal, Tomáš ; Komenda, Lukáš (referee) ; Dvořáček, Jiří (advisor)
This thesis is focusted in design of supporting frame of lift cage. Working load of frame is 1000 kg (13 people). Nominal speed is 2,5 m/s. First part is focusted in design of car frame. Car frame is made from steel bent profiles, connected each other with bolts. This work also contains final elemnt analysis of frame. Structure is analyzed by software Autodesk Inventor.
|
|
|
Calculation of heatexchanger
Kvapil, Matěj ; Naď, Martin (referee) ; Klučka, Ivan (advisor)
This bachelor thesis focuses on strength calculation of a heat exchanger according to ČSN EN 13445. First stage is an introduction into the theme of heat exchangers and their calculation. Next part is about the calculation according to ČSN EN 13445 itself. Part of this thesis is also strength analysis of selected items using numerical method (FEM). Annexes include calculation in software Microsoft Excel and basic drawings of items.
|
|
|
Solid Edge - Design of Omnidirectional Mobile Robot Platform
Poul, Ota ; Šoustek, Petr (referee) ; Matoušek, Radomil (advisor)
The bachelor thesis deals with design of three and four wheeled omnidirectional mobile robot platform. Design of both platforms is created in CAD software Solid Edge ST4. The result of this work are 3D models of mobile robot platforms for drawing documen-tation and subsequent realisation of platforms using predefined motor units. For both variants of the platform a stress simulation and visualisation were created within the possibilities of applied software.
|
guest ::
