|
|
Gearbox for portable power generator
Kolka, Roman ; Hubáček,, Tomáš (referee) ; Bradáč, František (advisor)
The submitted project deals with a complete design of a gearbox of a portable ground power generator designed for preflight preparation of helicopters. The gearbox has been designed to meet given specifications, which are based on required electrical parameters of the entire power unit and with regards to parameters of driving turbine engine. The introductory section deals with a kinematical design of transmission gears with regards to required parameters and design constraints. The kinematical design determines whole concept and resulting form of the gearbox. Next part deals with optimization of gearing, the design of wheel bearing, and design of oil system. The implementation part of the project consists in the engineering design of the gearbox, which was made in 3D environment Pro/Engineer. The design is reviewed and first operational results of manufactured and tested gearbox are discussed in the concluding section of this work.
|
|
|
Bridge across the Morávka river at km 6.205
Hollý, Tomáš ; Marván, David (referee) ; Nečesal, Petr (advisor)
The subject of the thesis is to design and consider steel superstructure of a composite steel-concrete road bridge. It is a continuous beam with seven spans of 36,0 + 57,0 + 75,0 + 90,0 + 75,0 + 57,0 + 36,0 = 426 meters. The superstructure consists of welded I-beams, which pass into closed box girder. The calculations take into account the construction phase.
|
|
|
Modern Turbocharger Rotor Supports
Kortán, Daniel ; Raffai, Peter (referee) ; Knotek, Jiří (advisor)
This bachelor thesis focuses on the options of impositions of turbocharger rotors. The first part focuses on the construction of turbochargers and description of the principle of turbocharging engines with internal combustion. The second part focuses on the description of the construction of rolling and sliding bearings and explanation of options the particular types of impositions used in turbochargers nowadays.
|
|
|
Study of fatigue life of roller bearings type 6204 -2Z
Poláček, Vojtěch ; Svoboda, Petr (referee) ; Klapka, Milan (advisor)
This bachelor thesis deals with the basic description of produced by fatigue failure of ball bearings. In the paper there is a description of basic diagnostic methods of machine parts. Following there is a study of vibration, their recording and the evaluation concerning bearing lifetime. The aim of the experimental part of the paper is to check the functionality and suitability od the VDT2000 analyzer and VDT Control Center software, both made by company VidiTech, s.r.o. together with the SA67 laboratory experimental stations owned by the Department of Design at Faculty of Mechanical Engineering, which were used for examining the 6204-2Z bearings. The aim of the lifespan exam is to confirm the reliability of the bearing failure warning by the analyzer and to assess the ability to record the first stages of bearing damage.
|
|
|
Study of bearing noise regarding accuracy of machining
Studýnka, Pavel ; Sabo, Karol (referee) ; Klapka, Milan (advisor)
This bachalor thesis deals with connection between the quality of surface of raceways of a bearing and vibrations in operation. This thesis describes basic geometrical parameters of a bearing that have main influence on its resulting quality and vibrations. It presents methods to evaluate the quality of the raceways surfaces and their connection between them. As a part of the thesis is an experiment, which should prove, what is the connection between the measuring of quality of the surface of raceways and measuring the vibrations of bearings during the process, by the way used in the company KOYO Olomouc. The quality of raceways is evaluated on a measuring device MUK-F 300 and vibrations on IL 100R/2000.
|
|
|
Spiral conveyor
Bednář, Jiří ; Malášek, Jiří (referee) ; Kašpárek, Jaroslav (advisor)
The aim of this bachelor thesis is a proposal construction of the spiral conveyor serving to the transport wheat from the container to the grinding equipment. The introduction describes the theoretical part of the screw conveyors, spiral conveyors and transported materials. This is followed by construction solution and calculation of the most important parts of the conveyor.
|
|
|
Spiral conveyor
Bednář, Jiří ; Malášek, Jiří (referee) ; Kašpárek, Jaroslav (advisor)
The aim of this bachelor thesis is a proposal construction of the spiral conveyor serving to the transport wheat from the container to the grinding equipment. The introduction describes the theoretical part of the screw conveyors, spiral conveyors and transported materials. This is followed by construction solution and calculation of the most important parts of the conveyor.
|
|
|
Design of milling machine spindl
Betlach, Jakub ; Hrbáček, Jakub (referee) ; Blecha, Petr (advisor)
The aim of this bachelor’s thesis is the construction of the milling machine spindle. The first part includes research in the structural part of machine-tools spindles that are used currently. The first section also contains an overview of producers of machine-tools and their milling machines. The second part is focused on the design of the spindle according to selected parameters, including the necessary calculations. This thesis also includes spindle assembly drawing and 3D model created with Autodesk Inventor Professional 2011.
|
|
|
Contactless torque sensor
Křemen, Jan ; Novotný, Pavel (referee) ; Píštěk, Václav (advisor)
This bachelor´s thesis aims to develop the conceptual and experimental study of the assembly function for non-contact measurement of torque basic project design and the monitoring of key components of the mechanical dimensions of the prototype device BMK-1. The object of this work is only a part of the mechanical equipment. Inspections will be conducted through simple calculations of elasticity strength.
|
|
|
Stroke mechanism of crane trolley
Malár, Martin ; Pokorný, Přemysl (referee) ; Škopán, Miroslav (advisor)
This bachelor thesis deals with the design of the stroke mechanism of the crane trolley, maximum weight of loads is 16 000 kg. The work is divided into two parts: a written part and a practical part. In the written part of this work there are the main dimensions of lift and control cable drum strength solved. The calculation is subject to quantities that are given by assignment. Choice of the electric motor, gearbox and follow-up control of the stroke speed according to customer requirements is discussed further. The second part includes production drawings, in which are included the total set of the stroke mechanism and other assemblies and production drawings.
|
guest ::
