|
|
Technickoekonomické hodnocení nových technologií zakládání porostu
Sláma, Jan
This thesis is focused on the measurement of transverse inequality of seed rate of the pneumatic seed drills. The first section describes the types of sowing, divisions of seeders and a description of the most common sowing units. The practical part is devoted to measurement of transverse inequality of seed rate of pneumatic seed drill. The changes in accuracy of seed rate of the older seed drill were being monitored. Additional measurements were carried out with the seal insert mounted in a distribution head. This measurement simulated sowing in rows with row spacing 50 cm. The current trends in creation of crops are presented. The discussion contains important information acquired during the measurement. The conclusion summarizes the findings of the thesis.
|
|
|
Sport Timing System
Sláma, Jiří ; Jurnečka, Peter (referee) ; Kačic, Matej (advisor)
This Bachelor's thesis describes sport timing system. Main goal was to create aplication, that covers completely all requirements of IT at sport competition. To these tasks belong creating web pages, schedule and then wireless launch of stopwatch. Aplication was implemented in IDE Qt with using programming language C++.
|
|
| |
|
| |
|
|
Design of measurement robotized workcell
Tvardek, Michal ; Sláma, Josef (referee) ; Knoflíček, Radek (advisor)
This master's thesis focuses on the use of the Renishaw's Equator gauging system in cooperation with the industrial robot. The target is to design the robotized workcell which contains these two products. Robot acts as a manipulator for inserting and sorting out the workpieces into the "good" and "bad" pallets according to measured results from the Equator. Equator uses a parallel kinematics and probing system which is normally used on coordinate measuring machines. Therefore there is the introduction to the parallel and serial kinematic structures, to the problems of the coordinate measuring machines in the first part of this thesis. It was made a separation of the probing systems into a few basic categories, description of the typical representatives of these categories and of the other important accessories of the coordinate measuring machines, too. The second part of the thesis contains a description of the Equator gauging system, the industrial robot which I used and their accessories. In this part is mentioned a few examples of measurement automation in industry practice, too. The third part devotes to the design of the robotized workcell and contains all the important requirements for the realization.
|
|
|
Press LKDS 800
Kolbábek, Lukáš ; Sláma, Jaroslav (referee) ; Omes, Jiří (advisor)
The present Master´s thesis deals with the concept of press drive of Blanking press LKDS 800 used for blanking in automatic blanking line. The first part of the thesis is dedicated to the individual arrangements of press drives and servo press drives and to the description of main components. The second part of this thesis deals with the structural design of the drive. Based on the computation of the crank mechanism, several design solutions were suggested. From these solutions, the option with the lowest drive height is selected. This option, offers the computation of the main drive, flywheel, spur gearing and clutch/brake combination. This computation is followed by computations of individual construction nodes, which include a design and dimensioning of the individual joggles, shafts and bearings. The drawing of the press and clutch shaft assemblies with a list of items are also included.
|
|
| |
|
|
Stabilized operation of a 400 kV power line
Sláma, Jan ; Topolánek, David (referee) ; Blažek, Vladimír (advisor)
This thesis deals with eletrical calculations of long stabilized 400 kV power lines. The main objective is to determine the eletrical parameters of power line beginning in case the parameters of line end are known for various power factors. Also the calculation methods of power lines is generally dealt with. Power-voltage way of computation and a method of exact solution was used for the calculations as to control the results.
|
|
|
Geodetic Works During Reconstruction of Road Crossing in Uherské Hradiště
Lovecký, Marek ; Sláma, Jiří (referee) ; Bureš, Jiří (advisor)
This thesis is engaged in geodetic works related to the increase of the capacity of the road II/497 and the modification of the intersection with the road I/55 in the town of Uherské Hradiště. The work is mostly focused on the field of the engineering geodesy. It resolves the issues from the alignment during the construction to the focus of the construction itself. Individual survey procedures are analyzed in the context of the prescribed deviations specified in the project documentation or ČSN. Geodetic documentation for the selected measurements is worked out.
|
|
|
Connecting Footbridge
Sláma, Jakub ; Štrba, Michal (referee) ; Brosch, Petr (advisor)
The subject of this master’s thesis was desingn and assessments the connection of two buildings by footbridge corridor. The structure was designed as a lattice structure without verticals. Construction is stored on two pillars lattice design. Cladding footbridge was cosidered by glazing. Construction is freestanding and doesn’t load bordering adjacent buildings.
|
guest ::
