| |
|
Emergency preparedness and protection of the inhabitans in the national company Budějovický Budvar in the release of hazardous substances
JIRKA, Martin
The thesis describes the issue of emergency preparedness and protection of the inhabitants in the National Corporation Budweiser Budvar during the release of hazardous substances. The thesis is focused on important aspects that determine the drafting of emergency documentation. One of aspects is the amount of hazardous chemical - ammonia. The total ammonia content in the object is 22 tons. This amount is according to the Act No. 59/2006 Coll., concerning prevention of major accidents as a sub-limit amount and not as an object into group A or B. On these not-classified resources are not subject to some duties under this Act, especially the obligation to prepare an emergency documentation (except where the regional authority include in the emergency plan then must provide and update the required documents). This paper doesn´t discuss by the massive leakage of 22 tons of ammonia. On the basis of analyzes were identified two sources of the risk. The first is a reservoir about the content of 10 tons which is located on the roof of the engine room. Maximum real filling is around 6 tons. The second source of risk is an expansion tank about the content of 14 tons, which is located in the building with cylinderconicals tanks (CKT). Considered fulfillment of the expansion vessel is about 7 tons. Although in this case is not about buildings and facility in which is treated with such a amount of dangerous chemical substances, which would belonged to the relevant group, I will perform available analysis according to a regulations issued or supportively used to analysis and risk assessment in according to the Act No. 59/2006 Coll., concerning prevention of major accidents. Harmful effects of ammonia are another important aspect. According to the Notice of the Ministry of Interior No. 103/2006 Coll., concerning establish principles defining the emergency planning zone and the extent and method of preparation of an external emergency plan, ammonia is taken as moderately toxic substance that irritates the eyes, mucous membranes, and in high concentrations can cause death. The great advantage from the point of view of the protection inhabitants are the warning properties. Characteristic pungency is already known in very weak concentrations. Also disposal of hazardous concentrations isn't technologically challenging, due to its solubility in the water. Another dangerous effect, except the toxicity is its explosiveness (explosive limit from 15 to 28 %) and flammability. Fortunately controlled condensing pressure prevents ignition and explosion of ammonia. Risk of the explosion and ignition of ammonia isn´t analyzed in this thesis, because the range of effects caused by leakage of several tons, is from a toxicological point of view more threatening. Impacts of hazardous concentrations aren´t threat only for people but also for animals and the environment. The thesis focuses on the analysis and evaluation of risks. The results of this research are an important element of the draft of emergency documentation. During the processing is calculated with methods IAEA-TECDOC-727, Dow's Chemical Exposure Index, Estimation of toxicity and software modeling program ALOHA. Further research is being done by brainstorming and semi-standardized interviews with employees of the company. In conclusion of the thesis is appropriate the drafting of emergency cards and emergency documentation (although not in range under the Act of concerning prevention of major accidents), according to which the reaction proceeded for any leakage of dangerous chemicals (ammonia) into the environment and the protection of workers which occur at the public premises or in the premises of the zone of impact of ammonia spilled outside the area Budweiser Budvar, NC. The use of the draft of emergency documentation is also conditioned by the location of the object in relatively densely populated areas of the county town of České Budějovice.
|
|
Use of Interest Rate Models for Interest Rate Risk Management in the Czech Financial Market Environment
Cíchová Králová, Dana ; Arlt, Josef (advisor) ; Cipra, Tomáš (referee) ; Witzany, Jiří (referee)
The main goal of this thesis is to suggest an appropriate approach to interest rate risk modeling in the Czech financial market environment in various situations. Three distinct periods are analyzed. These periods, which are the period before the global financial crisis, period during the financial crisis and in the aftermath of the global financial crisis and calming subsequent debt crisis in the eurozone, are characterized by different evaluation of liquidity and credit risk, different relationship between financial variables and market participants and different degree of market regulations. Within this goal, an application of the BGM model in the Czech financial market environment is crucial. Use of the BGM model for the purpose of predicting a dynamics of a yield curve is not very common. This is firstly due to the fact that primary use of this model is a valuation of interest rate derivatives while ensuring the absence of arbitrage and secondly its application is relatively difficult. Nevertheless, I apply the BGM model to obtain predictions of the probability distributions of interest rates in the Czech and eurozone market environment, because its complexity, direct modeling of a yield curve based on market rates and especially a possibility of parameter estimation based on current swaptions volatilities quotations may lead to a significant improvement of predictions. This improvement was also confirmed in this thesis. Use of swaptions volatilities market quotations is especially useful in the period of unprecedented mone- tary easing and increased number of central banks and other regulators interventions into financial markets that occur after the financial crisis, because it reflects current market expectations which also include future interventions. As a consequence of underdevelopment of the Czech financial market there are no market quotations of Czech koruna denominated swaptions volatilities. I suggest their approximations based on quotations of euro denominated swaptions volatilities and also using volatilities of koruna and euro forward rates. Use of this approach ensures that predictions of the Czech yield curve dynamics contain current market expectations. To my knowledge, any other author has not presented similar application of the BGM model in the Czech financial market environment. In this thesis I further predict a Czech and Euro area money market yield curve dynamics using the CIR and the GP models as representatives of various types of interest rates models to compare these predictions with BGM predictions. I suggest a comprehensive system of three criteria, based on comparison of predicti- ons with reality, to describe a predictive power of selected models and an appropria- teness of their use in the Czech market environment during different situations in the market. This analysis shows that predictions of the Czech money market yield curve dynamics based on the BGM model demonstrate high predictive power and the best 8 quality in comparison with other models. GP model also produces relatively good qua- lity predictions. Conversely, predictions based on the CIR model as a representative of short rate model family completely failed when describing reality. In a situation when the economy allows negative rates and there is simultaneously a significant likelihood of their implementation, I recommend to obtain predictions of Czech money market yield curve dynamics using GP model which allows existence of negative interest rates. This analysis also contains a statistical test for validating the predictive power of each model and information on other tests. Berkowitz test rejects a hypothesis of accurate predictions for each model. However, this fact is common in real data testing even when using relatively good model. This fact is especially caused by difficult fulfilment of test conditions in real world. To my knowledge, such an analysis of the predictive power of selected interest rate models moreover in the Czech financial market environment has not been published yet. The last goal of this thesis is to suggest an appropriate approach to obtaining pre- dictions of Czech government bonds risk premium dynamics. I define this risk premium as a difference between government bond yields and fixed rate of CZK IRS with the same length. I apply the GP model to describe the dynamics of this indicator of the Czech Republic credit risk. In order to obtain a time series of the risk premium which are necessary for estimation of GP model parameters I firstly estimate yield curves of Czech government bonds using Svensson model for each trading day since 2005. Resulting si- mulations of risk premium show that the GP model predicts the real development of risk premiums of all maturities relatively well. Hence, the proposed approach is suitable for modeling of Czech Republic credit risk based on the use of information extracted from financial markets. I have not registered proposed approach to risk premium modeling moreover in the Czech financial market environment in other publications.
|
|
Project of starting a discount retail store in Stara Boleslav
Nováková, Jitka ; Fuchs, Jan (advisor) ; Cimler, Petr (referee)
This bachelor thesis deals with a possibility of starting a discount retail store located in Brandys nad Labem - Stara Boleslav. The theoretical part describes retail industry in the Czech Republic and also different types of retail stores and factors that affect them. Furthermore, the theoretical part also focuses on factors influencing consumer behavior in the Czech Republic. The practical section analyzes retail stores in Brandys nad Labem - Stara Boleslav. The thesis evaluates survey results with a focus on consumer buying behavior and preferred way of shopping in the area mentioned above.
|
|
Expert capacities of the Czech political parties: case study of defence policy
Bayerová, Anežka ; Němec, Jan (advisor) ; Vymětal, Petr (referee)
The thesis deals with marginally explored area of expert capacities of the Czech political parties with respect to the different organizational types of selected political parties and movements. The work aims to find out what expert capacities work for these types of political parties, how these experts are recruited in their position, whether it corresponds to their educational background and professional experiences with function, which are they holding in the expert authority. Work is elaborated in the form of case study, which focuses on the activities of defense policy expert commissions. The text is divided into two theoretical and one empirical chapters. The first chapter deals with the process of policy-making, its actors and activities associated with this process. The second chapter defines the various types of political parties first from the mainstream perspective (cadre, mass, catch-all parties), which complements the modern concept of business party and finally there is a typology of S. Wolinetz (office-seeking, vote-seeking, policy-seeking parties). The last empirical chapter presents the case study focused on four Czech political parties (TOP 09, KSČM, ČSSD and political movement ANO 2011) and their access to party expertise. The result of this work is to compare the level of analytical capacity across selected political parties/movements and testing of hypotheses formulated in the introduction of the thesis.
|
|
Anti-Plagiarism Services For Our Repositories
Mach, Jan
The presentation is focused on a comparative analysis of systems for detecting duplicates (called anti-plagiarism systems) suitable for repositories of ETDs in the Czech Republic. The paper describes the testing process and results. These results can help to decide, which system will be suitable as a anti-plagiarism tool for the control of theses and other types of gray literature.
Fulltext: idr-692_3 -  PDF
Slides: idr-692_1 - PDF; idr-692_2 - PDF
Video: idr-692_4 -  MP4
|
|
Modelling, parameter estimation, optimisation and control of transport and reaction processes in bioreactors.
ŠTUMBAUER, Václav
With the significant potential of microalgae as a major biofuel source of the future, a considerable scientific attention is attracted towards the field of biotechnology and bioprocess engineering. Nevertheless the current photobioreactor (PBR) design methods are still too empirical. With this work I would like to promote the idea of designing a production system, such as a PBR, completely \emph{in silico}, thus allowing for the in silico optimization and optimal control determination. The thesis deals with the PBR modeling and simulation. It addresses two crucial issues in the current state-of-the-art PBR modeling. The first issue relevant to the deficiency of the currently available models - the incorrect or insufficient treatment of either the transport process modeling, the reaction modeling or the coupling between these two models. A correct treatment of both the transport and the reaction phenomena is proposed in the thesis - in the form of a unified modeling framework consisting of three interconnected parts - (i) the state system, (ii) the fluid-dynamic model and (iii) optimal control determination. The proposed model structure allows prediction of the PBR performance with respect to the modelled PBR size, geometry, operating conditions or a particular microalgae strain. The proposed unified modeling approach is applied to the case of the Couette-Taylor photobioreactor (CTBR) where it is used for the optimal control solution. The PBR represents a complex multiscale problem and especially in the case of the production scale systems, the associated computational costs are paramount. This is the second crucial issue addressed in the thesis. With respect to the computational complexity, the fluid dynamics simulation is the most costly part of the PBR simulation. To model the fluid flow with the classical CFD (Computational Fluid Dynamics) methods inside a production scale PBR leads to an enormous grid size. This usually requires a parallel implementation of the solver but in the parallelization of the classical methods lies another relevant issue - that of the amount of data the individual nodes must interchange with each other. The thesis addresses the performance relevant issues by proposing and evaluation alternative approaches to the fluid flow simulation. These approaches are more suitable to the parallel implementation than the classical methods because of their rather local character in comparison to the classical methods - namely the Lattice Boltzmann Method (LBM) for fluid flow, which is the primary focus of the thesis in this regard and alternatively also the discrete random walk based method (DRW). As the outcome of the thesis I have developed and validated a new Lagrangian general modeling approach to the transport and reaction processes in PBR - a framework based on the Lattice Boltzmann method (LBM) and the model of the Photosynthetic Factory (PSF) that models correctly the transport and reaction processes and their coupling. Further I have implemented a software prototype based on the proposed modeling approach and validated this prototype on the case of the Coutte-Taylor PBR. I have also demonstrated that the modeling approach has a significant potential from the computational costs point of view by implementing and validating the software prototype on the parallel architecture of CUDA (Compute Unified Device Architecture). The current parallel implementation is approximately 20 times faster than the unparallized one and decreases thus significantly the iteration cycle of the PBR design process.
|
|
Population genetic analysis of Old Kladruber horse
Vostrá Vydrová, Hana ; Majzlík, Ivan (advisor) ; Karel, Karel (referee)
The Old Kladruber horse, along with the Lipizzaner horse, Andalusian horse and Lusitano horse, is of the original Italo-Spanish type. The Old Kladruber horse is kept in two colour varieties (grey and black). Because the population is closed, there is a concern about the loss of genetic variation. The genetic diversity and population structure were analysed in the Old Kladruber horse breed based on the pedigree information of animals that were registered in the Studbook to identify factors that may have affected the genetic variability of the breed. Pedigree records collected from 1729 to 2013 contained information on 7971 animals that were used in the analyses. The pedigree depth was up to 33 generations, with an average of 15.1 complete generations. The effective number of founders and ancestors contributing to the current genetic pool was 92.69 and 17.16, respectively. The average values of the inbreeding coefficient were as follows: 13% (with a maximum value of 29%) for the reference population (individuals that can currently take part in reproduction, n=612), 11% for the grey variety (with a maximum value of 25%) and 15% for the black variety (with a maximum value of 29%). The proportion of inbred animals was high (99%). The average rate of inbreeding in the reference population was 1%: 0.8% for the grey variety and 1.1% for the black variety, and the respective estimates of the effective population sizes were 52 for the reference population, 62 for the grey variety and 45 for the black variety. The estimated percentage of genetic diversity lost due to non-random mating within subpopulations and the reference population was 1.0, 1.0 and 1.2%, respectively. The total loss of genetic diversity in the reference population, in the grey variety and in the black variety was 11%, 13% and 17%, respectively.
|
|
Freezing technology of bull sperm in relation to its survivability and fertilization ability
Doležalová, Martina ; Stádník, Luděk (advisor) ; Jiří, Jiří (referee)
The aim of optimalization the insemination doses production is to provide the highest fertilization ability of spermatozoa during the demanding proces of processing fresh semen and its subsequent cryopreservation. Temperature changes causes spermatozoa damage during the cooling and freezing. Spermatozoa is exposed to cold shock and many others limiting factors, which leads to cell death and therefore to decline of fertilization ability of thawed insemination doses. For increasing spermatozoa resistance, exactly the plasma membrane resistance against cold shock was fraction of egg yolk LDL cholesterol (low density lipoprotein) at various concentrations into the comercially produced diluents added. It is believed that LDL acts possitively to plasma membrane and helps to maintain the fertilization ability of spermatozoa after thawing. Following step in the proces of insemination doses production is slow cooling of diluted semen and equilibration, when the straws are store at cooling box for 30 minutes to 240 hours. This period is necessary to penetrate of certain diluent components into the spermatazoa also maintain the balance between their intracellular and extracellular concentration. Also important is subsequent freezing temperature gradient of insemination doses. The most suitable freezing method is based on computer controlled temperature decline in freezing chamber which allows the precise control of ice crystals formation that could tear and kill the cell.
During 2012 to 2016 was repeatedly collected semen from the group of breeding bulls (n = 27, Holstein and Czech Fleckvieh breed) at AI centre. Semen which fulfill the standard entrance conditions in first step was evenly into several parts divided. For dilution the three types of comercially diluents AndroMed, Bioxcell and Triladyl with and without LDL addition were used. Into the diluents AndroMed and Bioxcell the concentration of LDL 4 %, 6 % and 8% into the dilent Triladyl 6 %, 8 % and 10 % was added. Diluted semen was filled into the glass capillares with volume 0,1 ml and temperature +4 °C. Subsequently the sample was placed to cold bath (0°C) for 10 minutes. Then the volume of capillare with physiological solution (37 °C) was mixed and for next 120 minutes was incubate. The effect of cold shock to proportion of live spermatozoa was evaluated by using Eosin and Nigrosine staining technique during heat test of spermatozoa survivability after spermatozoa heating and after 120 minutes of incubation.
The more suitable semen diluents which provide the higher spermatozoa resistance against cold shock were AndroMed and Bioxcell. Together the possitive effect of LDL addition into the diluents to lower decrease of proportion of live spermatozoa during heat test was found (P<0.05). The most suitable LDL concentration which had a favorable influence at spermatozoa resistance against cold shock was 6 % in diluent Bioxcell. Values of the proportion of live sperm were higher at the beginning of the heat test (+1.31% to + 3.2%) and after 120 minute incubation (+5.82% to +8.41%) compared to other diluents with and without addition of LDL.
In the next step the process of equilibration was optimized, is an important part of insemination doses production. The effect of the length of equilibration for subsequent fertilization ability of spermatozoa was evaluated using spermatozoa motility based of CASA and proportion of live spermatozoa after thawing and during heat survival test lasting 120 minutes (37 ° C). Suitable semen was diluted by comercially used diluent AndroMed based on soya lecithin, filled into the straws (0.25 ml), cooled and equilibrated in cooling box for 30, 120 and 240 minutes and freezed in programmable freezing box applying four types of freezing curves differing in temperature rate decline. There was used standard and by producer recommended 3. phase freezing curve, then 2. phase freezing curve, and 3. phase freezing curve with slower as well as rapid decline of temperature rate in freezing chamber, compared with standard freezing curve. The highest spermatozoa motility was found using 240 minutes of equilibration by +2.72% and +4.58% compared to other lengths of equilibration (P <0.05 to 0.01). The highest proportion of live spermatozoa was found using 120 minutes of equilibration (+6.87 % and +8.68 %). The highest average spermatozoa motility during heat test after thawing was achieved by using 2. phase freezing curve (from +2.97% to +10.37%, P <0.05), also in the proportion of live spermatozoa (from + 4.37% to +8.82%, P <0.01). When evaluating interaction between the length of equilibration and freezing curve (standard 3. phase and 2 . phase freezing curve), the highest average spermatozoa motility and proportion of live spermatozoa using 240 minutes of equilibration by both freezing curves was reached, there was no statistically significant differences. As well as, in all evaluated parts of this study the individual differences between ejaculate of bulls and within semen from one bull (P <0.05) as secondary effect were found.
To maintain good fertilization ability of semen during cryopreservation is necessary to increase the spermatozoa resistance against cold shock using addition of correct concentration of LDL into the commercially used diluents AndroMed and Bioxcell. Subsequently the fertilization ability of insemination dose is influenced by cooling, the length of equilibration and freezing. The length of equilibration 120 minutes and more as well as gentle way of freezing according to freezing curve, which ensures a gradual decrease of temperature in freezing chamber provided the higher average spermatozoa motility and proportion of live spermatozoa.
|
|
E-learning support for lifelong training
Žažo, David ; Husa, Jiří (advisor) ; Marek, Marek (referee)
The bachelor thesis deals with the process of creating an e-learning course for the personnel operating with the camera system of the municipal police in Chomutov. This course is created on the base of need to introduce the controlling software IndigoVison Control Center to the current employees and also to the new employees. During the course, the participants get familiar with the features, options, and operating principles of the software. At the end of the course, the knowledge gained by completing the course is validated by the final test. The entire course is evaluated, based on test results and interviews with the participants. The theoretical part deals with e-learning, it mentions the advantages and disadvantages as well as the specifics associated with adult education. The practical part is a detailed presentation of the course, which is fully implemented in an environment of MoodleCloud and it is practical result of the thesis.
|
guest ::
