|
| |
|
|
Analysis of the electrical power measurement system in the local distribution network Pod Palackého vrchem
Hájková, Barbora ; Orságová, Jaroslava (referee) ; Jurák, Viktor (advisor)
The diploma thesis introduces a detailed analysis of the local distribution system (LDS) Pod Palackého vrchem (PPV) in the Brno, parameters of power transformers and cable routes between them. The elements of the electrical network that are influencing the balance of reactive power are described along with its sources and appliances. In the next part is defined the present concept of long-term measurement in the LDS by using current and voltage sensors. This part deals with calculations of power losses in the power transformers and the cable lines together with uncertainties concerning power measurement in the field of energetics. The essential part of the thesis focuses on the analysis of the temporary measurement implementation in the LDS, data processing along with the comparison of measured values from temporary measurement with values from permanent measurement. In conclusion, the error of the system is determined.
|
|
|
Current source for the solid-state laser amplifier
Žilka, Martin ; Duz, Aleksei (referee) ; Novák, Lukáš (advisor)
This thesis deals with theoretical design of solid-state laser beam amplifier power supply. The introductory part contains a description of operation principles of some step-down DC/DC converter topologies, including their advantages and disadvantages. The next chapter describes design issues of a DC/DC converter design, including full schematic diagram. The conclusion is focused on practical assembling and testing of the designed device.
|
|
| |
|
|
Analysis of high-speed induction motor
Klíma, Jiří ; Ondrůšek, Čestmír (referee) ; Vítek, Ondřej (advisor)
This thesis deals with the problem of the high-speed induction machines. In the introduction the design of the machines and problem areas are discussed. The feeding from the frequency converter and the mechanical strength of the rotor appear to be the biggest problem. High-speed engines with solid rotors were designed. The first model is equipped with a conductive cooper layer on the surface. This model is exposed to harmonic and non-harmonic input voltage and then the results of the simulations are compared. The following model of the thesis is equipped with axial slots. In the practical part of the thesis no load measurement is taken. One point was measured at nominal frequency. At the end of the thesis the results of the measurements are compared with the results of the figures extracted from Maxwell software.
|
|
|
Optimalization of Power Electric Engineering Processes by Genetic Algorithms
Paar, Martin ; Hradílek, Zdeněk (referee) ; Skala, Petr (referee) ; Toman, Petr (advisor)
Current trends in regulation of electricity supply continuity in the power engineering industry includes introduction of systems and customers standards. The electricity market liberalization in the European Union is speeded up the process furthermore. Companies included in the distribution network bussiness therefore began to be interested more in the evaluation of risks associated with the aplication of these standards. The aim of the thesis is to minimize the expenses caused by power losses of the distribution network by means of distribution network reconfiguration depending on the standard selection. For the minimization two of the Genetic algorithms was selected. As an criterion the overall expenses caused by power losses and the expenses caused by an electricity shortage. Furthermore the influence of the inclusion of the power loss to the calculation on the operation costs for given regulation standards. Two contemporary standards - finish and portugues - are considered together with three experimental standards. The aim of including experimental standards is to complete the regulation standards with parameters uncovered in the portuguese and finish standard. The results described in the thesis can be used in the distribution network optimization process from the point of reliability and operational costs.
|
|
|
Efficiency map of synchronous machine
Gargulák, Jiří ; Marada, Tomáš (referee) ; Pruša, Radomír (advisor)
Subject of this bachelor thesis is application of interpolation on efficiency maps of synchronous servo-engines. Nearest neighbor interpolation, inverse distance weighting and bilinear interpolation is used. Another part of this thesis is measuring on drive of one axis on machine tool, which is made out of frequency convertor, synchronous engine and a ball screw. Also another subject of this thesis is research of power losses in synchronous engine, frequency convertor and ball screw.
|
|
| |
|
|
Step down DC/DC converter with high efficiency
Chudý, Andrej ; Cipín, Radoslav (referee) ; Procházka, Petr (advisor)
This bachelor's thesis deals with design and realization of several versions of DC/DC buck converter. The theoretical part of the bachelor's thesis is focused on the general analysis of DC/DC converters with a detailed description of the buck converters. Another part specializes in the analysis of the current state in this field, where the basic differences between the synchronous and diode rectifier are explained, electromagnetic interference and GaN transistors are described. Subsequently, the thesis involves the design and calculations of necessary parameters of the buck converter. Calculations are verified by simulation and subsequent production of the first prototype. The basic measurements are performed on the prototype. Detected deficiencies of the prototype are removed in version 1.0. In order to achieve higher efficiency, innovated version 2.0 and version with GaN transistors are produced. The thesis is finished by comparing created buck converters.
|
|
|
Design of cooling of electrical machines for production machines and systems
Vaněrková, Tereza ; Vlach, Radek (referee) ; Huzlík, Rostislav (advisor)
The aim of this thesis is to design the water-cooling system for a synchronous motor with an output of 10kW. The power loss was analytically determinated. For the initial water-cooling system and for two design proposals, thermal models were calculated in Ansys. The same boundary conditions were set for all three models. Then the analysis results of the temperature distribution on the machine surface and in the slots were compared. The comparison also includes the economical cost of the production and service of the machine. Then the production documentation was created, consisting of the assembly drawings and a simplified technological process.
|
guest ::
