|
|
Winding diagnostics using surge test
Vojtěch, Pavel ; Šlezingr, Jan (referee) ; Drápela, Jiří (advisor)
Master‘s Thesis deal with analysis given to diagnostic method plus her applicability to failure detection electrical machine plus apparatus in different phases their live. A further realization physical model with subtransient generátor PSG204A 4kV, for teach – in disorder on single – layer air coil plus stator winding induction motor inclusive evaluation results test.
|
|
|
Analysis of concentrated windings of PMSM
Menoušek, Lukáš ; Cipín, Radoslav (referee) ; Vítek, Ondřej (advisor)
This thesis deals with the design, principles of permanent magnet synchronous machines and an analysis of their properties. As part of the work is done familiarization with the materials of permanent magnets and their arrangement, as well as construction of the engine where they are discussed types of winding machine configuration, types of motors with permanent magnets and the list of implemented solutions. In the next section of this paper is an analysis of the properties of selected types of concentrated winding with a focus on the emergence of harmonics. These data are compared with the model of the engine in the FEMM. Furthermore, a comparison of the calculations of these types of engines and their simulation in RMxprt.
|
|
|
Analysis of dynamic load from induction machine current signature
Pavláček, Jan ; Ondrůšek, Čestmír (referee) ; Huzlík, Rostislav (advisor)
This thesis focuses on the analysis of the dynamic behavior of the load from the measurement of stator currents of induction motor. Work is sorted from basic engine failures equations, mathematical models, types of signal processing, simulation and measurement. The practical part deals with the design of the motor model in Matlab Simulink, the simulated and the measurement of the pump BETA 12 YC On the Department of Fluid Engineering Victor Kaplan. Use appropriate types of signal processing evaluate the results. The aim of this work is to analyze the dynamic changes of the load.
|
|
|
DC Motors Analysis and Innovation
Šimko, František ; Kuchyňková, Hana (referee) ; Hájek, Vítězslav (advisor)
The thesis aims to explain the design a prototype of an innovated small engine. It is divided into three main parts. The first part is focused on the analysis of low power DC small engines available on the market. The second part consists of measuring, construction and loss analysis of a DC small engine with permanent magnets. The last part deals with the possible innovations of a small engine with permanent magnets and subsequent implementation of some of them. The innovations are supported by calculations and simulations.
|
|
|
Measurement of the asynchronous motor
Svetlík, Martin ; Ondrák, Tomáš (referee) ; Běloušek, Josef (advisor)
The work deals with the methods of measurement of various types and characteristics of induction engines is divided into three main chapters. The first chapter introduces us to the history superficially induction engines and the direction of work. The second chapter is devoted to different types of tests on this induction engines. The third chapter lists the results of measurements on two engines also known as type AOM090L02-016 (which is equipped with single layer winding) and type AOM090L02-017 (which is equipped with a double layer winding). In the end this work describing measurement of torque characteristics from run-up characteristic by using PC and freewheel.
|
|
|
Measurement of induction machines
Sporni, Peter ; Huzlík, Rostislav (referee) ; Janda, Marcel (advisor)
This work dissert about problematics of induction engines, which are the most used types of electrical drives used in present time. At the beginning we will explain their construction and its influence to the characteristics of the engine and possibilities of their regulation. In the next part we will describe some basic types of measurments implemented on these engines. To verify the theory which was described in this work we will discuss measurments realized on concrete types of engines. At the end we will calculate the main dimensions for one of the measured engine.
|
|
|
Efficiency Improvement of Small Induction Motors
Vilím, Martin ; Veselka, František (referee) ; Hájek, Vítězslav (advisor)
In this bachelor´s thesis I discuss about asynchronous engines in general, describe their construction and principle of operation, using. It also includes measurements of a specific motor and design engine. The first part deals with theprinciple of the engine options including the fundamental control over speed and torque. The second part deals with the measurement of the size of the searchengine and losses. The last part provides a proposal for a new induction motor.
|
|
|
Options for increasing the efficiency of small motors.
Kusý, Karel ; Janda, Marcel (referee) ; Hájek, Vítězslav (advisor)
This bachelor thesis concerns itself with the possibilities of achieving higher efficiency of small asynchronous motors and their manufacturing costs. The following chapters describe the design, function and principles of speed regulation of the asynchronous motor. Next, losses that occur during motor operation and ways of reducing them, are described. The last chapter of the thesis addreses factors that influence the manufacturing costs of the asynchornous motor and evaluates the material costs of one modified motor.
|
|
|
Classification of asynchronous motors
Čala, Václav ; Dušek, Jiří (referee) ; Singule, Vladislav (advisor)
This diploma thesis deals with a creation of a “Classification Document” of asynchronous motors with a short-circuit armature with axial heights of 355, 400, 450, 500, and 560 mm. Furthermore, it is concerned with a creation of an integral design documentation for the production and assembly of these motors at the company TES VSETÍN, s.r.o. By writing this diploma thesis I would like to achieve a simplification of communication with the customers during the processing of asynchronous motors orders and to speed up the processing of asynchronous motors orders not only in the design department but also the complete technologic preparation of the production which will surely be provided by this integrated documentation.
|
|
|
Brakes and retarders of commercial vehicles
Kalnický, Jakub ; Zháňal, Lubor (referee) ; Fojtášek, Jan (advisor)
This bachelor's thesis is specialized search dealing with brakes of commercial vehicles. The work is divided into six main parts. The first part deals with genesis of brakes. The second part informs about fundamental terminology and definition of braking. The third part deals with distribution of braking systems by their purpose. Contents of fourth and fifth parts are friction brakes and retarders. The last part is dedicated to development trends of brakes.
|
guest ::
