|
|
Feed Pump Condesing Steam Turbine
Uherek, Jan ; Kubiš, Zdeněk (referee) ; Fiedler, Jan (advisor)
This diploma thesis focuses on designing impulse stage steam turbine to be used as the feed pump drive. I consecutively carried out thermodynamic calculation, seals and bearings layouts, with the aim to determine the steam mass flow through the turbine. Furthermore, I conducted turbine blade toughness check-ups, determined the rotor critical rotational speed, check-up rotor critical place (bearing pin) for torsion, and created a clutch screws design. The final part of this thesis pursues the other operating states of the turbine. This thesis is amended by a mechanical drawing of the turbine transection.
|
|
|
High-speed Condesing Steam Turbine
Klíma, Petr ; Trojan, Aleš (referee) ; Fiedler, Jan (advisor)
ith one controlled extraction and one uncontrolled extraction, calculation of the flow channel at all stage, design and calculation of the regulation valve and create connection diagram of steam turbine and air cooled condenser. At the beginning of this work is an overview of manufacturers of steam turbines and their unified products. Master thesis was developer with G-Team, a.s. as using calculations and the instructions given in the recommended literature with supporting CFD simulations to determine the loss coefficients and FEA simulations to determine the eigenfrequencies blades.
|
|
|
Condensing Steam Turbine with superheating
Urbánek, Martin ; Weber, Norbert (referee) ; Weber, Norbert (referee) ; Fiedler, Jan (advisor)
The thesis is focused on designing of condensing steam turbine with reheating for combustion of biomass. The turbine is developed to be tandem compound-regenerative with five uncontrolled extraction points. Optimization of reheating pressure is made in the turbine's cycle. The turbine outlet is constructed to lead down to the water cooled condenser. Thesis includes the calculation of heat cycle with the draft of flow channel of high pressure and middle-low pressure turbine. Detailed calculation of middle-low pressure turbine, including stress-strength analysis, is performed. The thesis provides an evaluation of flow scheme of 100 % and 75 % of generator’s power output and the drawing of middle-low pressure turbine in longitudinal section.
|
|
|
Condensing Steam Turbine
Řezníček, Ondřej ; Václav, Urbánek (referee) ; Urbánek, Václav (referee) ; Fiedler, Jan (advisor)
The theme of this thesis is design of single body condensing steam turbine of 50 MW to saturated steam for new nuclear power plant generation. In the thesis is made design and calculation of balancing scheme. On the basis of the calculation is made blades part of turbine. Furthermore, the thesis solves basic strength and structural calculations. The result is drawing of longitudinal cut of the turbine.
|
|
|
Condesing Steam Turbine 25 MW
Mašek, Martin ; Norbert, Weber (referee) ; Norbert, Weber (referee) ; Fiedler, Jan (advisor)
Master’s thesis deals with design and calculation of one body condensing steam turbine of 25 MW with samples for paper-making industry. The thesis is focused on calculation of the turbine’s heat balance with two technological samples and regeneration which consists of two low pressure heaters and a deaerator with a power reservoir. The steam turbine is designed with a water cooling condenser with down output. The flow part is calculated with lengths of blades. There are basic strength and proportion calculations. In the end of the thesis the turbine’s heat balance is recalculated to 80% and 105% scheme according to an assignment. Another part of this thesis is a drawing of a longitudinal cut of the turbine including a connector with a gearbox.
|
|
|
Condensation Steam Turbine for Combi-cycle
Pavlíček, Martin ; Ing.Ondřej Štěpánek (referee) ; Fiedler, Jan (advisor)
This thesis named Cosdensing steam turbine in combi-cycle deals with the calculation of thermal balancing scheme and the design of turbine. This double body steam turbine with combined HP-IP part and double-flow LP part does not have any additional samples of technological steam. LP part has two side outputs to the water-cooled condensers. There is a basic calculation of force effects on the LP part at operation. The thesis also includes a drawing of a longitudinal cut of LP part and its layout, including positron of the condensers.
|
|
|
Steam turbine
Pokorný, Tomáš ; Novotný, Zdeněk (referee) ; Fiedler, Jan (advisor)
Condensing steam turbine. Master's thesis of master's studies of 2th years. This master's thesis is technical research. The contents of this technical research are an analysis of a mechanical equipment of that are used for condensing steam turbine, thermodynamic calculations of passage channel for specified inlet and outlet conditions of steam, design and construction, drawing of the turbine axial cross section, operating scheme of turbine and economic analysis of operation.
|
|
|
Condensing Steam Turbine
Kracík, Petr ; Martinec, Jiří (referee) ; Fiedler, Jan (advisor)
Diploma thesis named Condensing steam turbine deals with heat scheme balancing computation of condensing steam turbine K55 and her design. This turbine with 5 unregulated take-offs and overpressure blading type, is computed with (c_a/u) method in the middle of blading diameter. Regulation degree is chosen with impulse blading and feet cross section is checked on durability. At the end of the thesis turbine consumption characteristic is derived from the zero output up to the nominal output. Integrated part of this thesis is conceptional design of longitudal turbine section.
|
|
|
Condensing steam turbine
Girman, Peter ; Průdek, Miloš (referee) ; Fiedler, Jan (advisor)
The master´s thesis concentrates on a project of condensing steam turbine for existing heating plant with back pressure turbine. The master´s thesis subject consists in the thermodynamic calculation of regulating stage and turbine stages. Design documentation is worked up according to the calculated record. From calculated power of turbine is worked a basic project of gearbox and disposal arrangement system.
|
|
|
Mathematic model of steam turbine
Kroliczek, Filip ; Dokoupil, Jakub (referee) ; Pivoňka, Petr (advisor)
The goal of this thesis was to create a mathematical model of a steam turbine based on the data acquired by measurement, and to verify its behaviour. The first part contains research, which is supposed to introduce basic principles of the steam turbine and description of important construction parts and the possibilities of control. The second part describes the experimental identification method of least squares, used for the calculation of an ARX model of the steam turbine. Finally, the last part focuses on the program environment used for creation of the mathematical model and explanation of measured data analysis process. Furthermore this segment describes the created simulation program as well as a visualisation of the dynamic processes in the steam turbine, including the design of control.
|
guest ::
