|
|
DC/DC converter for car-audio amplifier
Šmarda, Vladislav ; Vorel, Pavel (referee) ; Červinka, Dalibor (advisor)
This Bachelor thesis deals with the design and construction of a resonant switching power supply for car audio-amplifier. The main subject of the theoretical part is the mathematical description of the applied ZVCS Push-Push topology. Also a general guide, for designing this type of topology is mentioned. There is described the optimalization procedure of the main switch mode power transformer with respect to the high efficiency of the proposed power supply. Then the designed power supply is made and tested.
|
|
| |
|
|
The Design Methods of Equipments for Audio
Kondler, Radim ; Vrba, Kamil (referee) ; Mišurec, Jiří (advisor)
The work is focused on equipment used in audio, such as a loudspeaker crossovers, amplifiers and preamplifiers. There are theoretically described loudspeaker crossovers, their parameters, types of structures derived from the frequency filters with their parameters. Further deals about audio amplifiers and both voltage and power, their theories, parameters, and distribution.
|
|
|
Design and realization of switching class audio power amplifier
Levocký, Kristián ; Götthans, Tomáš (referee) ; Brančík, Lubomír (advisor)
This bachelor thesis describes design of audio amplifier of class D with power 2x100W. Power part is designed with integrated circuit TAS5630B made by Texas Instruments and correction preampifier unit is regulated by four potentiometers , controled by integrated circuit TDA1524A. Switching supply is regulated by circuit TOP261EN. Whole device is installed in device box with graphic display and control components.
|
|
|
Design and realization of an active subwoofer
Hrdina, Robin ; Kledrowetz, Vilém (referee) ; Šteffan, Pavel (advisor)
This bachelor thesis describes the design and construction of a one-channel amplifier 200 W into 8 load for an active subwoofer. The design consists of an active correction preamplifier and output stage. Preamplifier is created of integrated operational amplifiers and is controlled by two potentiometers, input switch and phase switch. Output stage is created of integrated circuits LM3886T by Texas Instruments. Both stages were constructed on PCBs and were measured their parameters.
|
|
|
Class D audio amplifier with PWM modulation
Arvai, Luboš ; Petržela, Jiří (referee) ; Kratochvíl, Tomáš (advisor)
The aim of this project is design audio amplifier working in class D with power output 2x20 W. In the beginning is shortly described a principle of amplifiers in class D. In the next chapter is block circuit diagram and requirements list for individual blocks. In next section is closely described circuit design of correction preamplifier, PWM modulator with driver of power transistors, power stage and output filter. At the conclusion is summarized experimentally obtained knowledge. On the basis of this knowledge is described modification of original design.
|
|
|
Construction of class T audio amplifier
Tejmlová, Lenka ; Slezák, Josef (referee) ; Petržela, Jiří (advisor)
The aim of my bachelor’s thesis is to collect information about amplifiers, working in the T class. Because these amplifiers are usually used as digital power processing audio amplifiers, we mostly insist on the ability of sending, the signal without distortion, to amplify the frequency broadband signal, to obtain the high efficiency of the output stages and to obtain the peak quality of the sound. My task is to gather information and facts of principle of the function of the audio amplifiers working in the T class and reasonably priced integrated circuits of this class. Furthermore I am going to focus on the design of wiring of this amplifier with the 2x20 watts output, including the correction pre-amplifier, which provides correction of the heights, basses and volume. The amplifier is realized, in the end of bachelor’s thesis, there are measured it’s characteristics, which are compared to theory.
|
|
|
Vacuum tube phono amplifier
Hrubý, Ondřej ; Novák, Lukáš (referee) ; Musil, Tomáš (advisor)
This master´s thesis deals with a design and simulation of an audio power phono amplifier using vakuum tubes. The frequency response of suggested solution should comply with the norm specified by RIAA. It also describes a vacuum tube basic description and also its advantages for audio applications and principle of usage a magnetodynamic pick-up. Last part contains a design of microprocessor system and power supply.
|
|
|
Class D 2.1 audio amplifier for laboratory measurements
Děcká, Klára ; Polák, Ladislav (referee) ; Kratochvíl, Tomáš (advisor)
This semestral thesis deals with a draft and construction of the design of an class D audio amplifier with pulse width modulation. The resulting design consists of a supply protection, an active crossover and the output power stage itself. The amplifier is made in 2.1 configuration, the amplifier for mid/high audio frequency drives 2 × 30 W output into a 8 load, subwoofer drives 1 × 100 W into a 2 load. The control centre of the whole application is an integrated circuit TPA3116D2 by Texas Instruments company. The resulting audio amplifier will be used as a device for laboratory measurements.
|
|
|
Class AB stereo audio power amplifier with electron tubes
Herbrych, Vojtěch ; Šotner, Roman (referee) ; Kratochvíl, Tomáš (advisor)
Bachelor thesis deals with design and create construction drawings of audio amplifier using vaccum tubes with output power 20 W/4 and works in class AB. At least two inputs are included for mobile, computer and others. The device includes 2-band preamplifier with basic adjustment (bass and treble). For different channel volume is included balance adjustment. There is an audio-level indicator with „magic-eye tube“. This part of bachelor thesis contains theoretical explanation, design of amplifier´s schematic and design drawings.
|
guest ::
