|
Optical low dispersion rezonator as length sensor using optical frequency comb
Pravdová, Lenka ; Hucl, Václav ; Lešundák, Adam ; Lazar, Josef ; Číp, Ondřej
Ultra-high precis measurements are domain of lasers interferometers. An optical resonator measuring method using broad spectrum of radiation of an optical frequency comb was designed and experimentally verified at our workplace. The measuring of a quantity – a distance of resonator mirrors – is provided by its conversion to the value of repetition frequency of the pulse laser with mode-locked optical frequency comb. In this paper the comparison of the absolute scale of the optical resonator with an incremental interferometer scale is introduced. The incremental interferometer is implemented for verification of the optical resonator scale. The double beam incremental interferometer is operating at the wavelength of 633 nm and the measuring mirror with piezo actuator is used as one of its reflectors. It turns out that the major error signal is the reflection of the periodic nonlinearity of the incremental resonator scale. The relative resolution of our method reaches values up to 10-9 while maintaining measuring scale.
|
|
Automatic system for gauge blocks calibration optimized for legal length metrology
Buchta, Zdeněk ; Šarbort, Martin ; Čížek, Martin ; Hucl, Václav ; Řeřucha, Šimon ; Pikálek, Tomáš ; Dvořáčková, Š. ; Dvořáček, F. ; Kůr, J. ; Konečný, P. ; Lazar, Josef ; Číp, Ondřej
This paper presents a contactless system for automatic and contactless gauge blocks calibration based on combination of laser interferometry and low-coherence interferometry. In the presented system, the contactless measurement of the absolute gauge block length is done as a single-step operation without any change in optical setup during the measurement. The optical setup is combined with compact gauge block changer with capacity 126 gauge blocks, which makes the resulting system fully automatic. \nThe paper also presents in detail a set of optimization steps which have been done in order to transform the original experimental setup into the automatic system which meets legal length metrology requirements. To prove the measurement traceability, we conducted a set of gauge block length measurement comparing data from the optimized system and the established reference system and TESA–UPC operated in Czech Metrology Institute laboratory.
|
|
Network Architecture and Interconnection of Embedded Systems
Trchalík, Roman ; Drábek, Vladimír (referee) ; Srovnal, Vilém (referee) ; Švéda, Miroslav (advisor)
The thesis focuses on the architecture of embedded systems. It summarizes the current state of accepted standards from IEEE 1451 family, which deals with creating an environment for the sensors and their involvement in various networks. These standards describe the open, network-independent communication architecture for a sensor-based system. One of the main outcomes of this work is the architectures presented as case studies, which can be used as design patters for embedded applications. They are demonstrated on ZigBee technology suitable mainly for small devices with very low power consumption. Based on these studies the new design of universal gateway was proposed. Its major advantage is that it allows interconnection of the endpoints based on different sensor network technologies. Additionally, the thesis deals with modifying the routing protocol of ZigBee network in order to reduce power consumption required to transmit one data packet.
|
|
Optimization of network flow monitoring
Žádník, Martin ; Lhotka,, Ladislav (referee) ; Matoušek, Radomil (referee) ; Sekanina, Lukáš (advisor)
The thesis deals with optimization of network flow monitoring. Flow-based network traffic processing, that is, processing packets based on some state information associated to the flows which the packets belong to, is a key enabler for a variety of network services and applications. The number of simultaneous flows increases with the growing number of new services and applications. It has become a challenge to keep a state per each flow in a network device processing high speed traffic. A flow table, a structure with flow states, must be stored in a memory hierarchy. The memory closest to the processing is known as a flow cache. Flow cache management plays an important role in terms of its effective utilization, which affects the performance of the whole system. This thesis focuses on an automated design of cache replacement policy optimized to a deployment on particular networks. A genetic algorithm is proposed to automate this process. The genetic algorithm generates and evaluates evolved replacement policies by a simulation on obtained traffic traces. The proposed algorithm is evaluated by designing replacement policies for two variations of the cache management problem. The first variation is an evolution of the replacement policy with an overall low number of state evictions from the flow cache. The second variation represents an evolution of the replacement policy with a low number of evictions belonging to large flows only. Optimized replacement policies for both variations are found while experimenting with various encoding of the replacement policy and genetic operators. The newly evolved replacement policies achieve better results than other tested policies. The evolved replacement policy lowers the overall amount of evictions by ten percent in comparison with the best compared policy. The evolved replacement policy focusing on large flows lowers the amount of their evictions two times. Moreover, no eviction occurs for most of the large flows (over 90%). The evolved replacement policy offers better resilience against flooding the flow cache with large amount of short flows which are typical side effects of scanning or distributed denial of service activities. An extension of the replacement policy is also proposed. The extension complements the replacement policy with an additional information extracted from packet headers. The results show further decrease in the number of evictions when the extension is used.
|
|
Surface modification of glass fibers for polymer composites
Knob, Antonín ; Marek,, Aleš (referee) ; Burša, Jiří (referee) ; Čech, Vladimír (advisor)
The doctoral thesis is aimed at preparation of glass fiber reinforced polymer composites with controlled interphase formed by plasma-polymerized tetravinylsilane and tetravinylsilane/oxygen thin films. The thin polymer films of specific physico-chemical properties and thickness were deposited to improve interfacial adhesion of glass fiber/polyester composites. The fiber surface modification was performed by using plasma enhanced chemical vapor deposition in low-temperature RF plasma operating in an various effective power range and different treatment time. Test results were examined in relation to the interlayer thickness and different treatment conditions. The prepared interlayers were analyzed to evaluate physico-chemical composition and properties (XPS, RBS, ERDA, FTIR and spectroscopic elipsometry). Selected mechanical properties were evaluated by AFM. Mechanical response of plasma interlayers was evaluated by short beam shear test and direct method of testing the interfacial shear strength using microindentation. The interphase shear failure was controlled by the shear strength at the interlayer/fiber interface as follows from experimental and model data.
|
|
Relationship between petrographic parameters and technological properties of clastic sedimentary rocks used for crushed stone
Čermák, Martin ; Přikryl, Richard (advisor) ; Krutilová, Kateřina (referee)
This diploma thesis is focused on the finding and describing of the relationships between petrological parameters and technological properties of rocks used for the production of aggregates (crushed stone). Rock specimens were selected from a geological area of Culm (Lower Carboniferous age) in the area of Nízký Jeseník Mts. and Drahanská vrchovina uplands in the Czech Republic. Studied localities were selected on the basis of the current quarrying operations and also to represent the different strata. The six studied localities encompass Kobylí, Chabičov, and Bělkovice where Horní Benešov formation of Nízký Jeseník is exposed. Locality Valšov represents Andělské Hory formation and locality Nová Ves and Loštice represent Protivanov formation of Drahanská vrchovina uplands. Two specimens were taken from the locality Loštice (one from the second cut because there are produced low-grade aggregates and the third cut where high quality crushed stone is produced). A detailed mineralogical-petrographic examination of the samples was the first step, in an attempt to obtain their mineralogical composition and to identify the major rock-forming clasts. Thin sections were examined by standard polarizing microscopy. The auxiliary UV lamp and thin sections saturated by fluorescent substance were used for the...
|
|
Mechanochemical Preparation of Alumina-Ceria
Jirátová, Květa ; Spojakina, A. ; Tyuliev, G. ; Balabánová, Jana ; Kaluža, Luděk ; Palcheva, R.
Ceria containing catalysts play an essential role in heterogeneous catalytic processes. However, ceria shows poor thermal stability and low specific surface area and therefore, many studies have been done to improve its properties by combination with other oxides. Alumina-ceria is substantial component of the three ways catalysts, due to the ceria ability to function as the buffer of oxygen and to enhance the oxygen storage capacity of the catalysts. Ceria in these catalysts also functions as structural promoting component, increasing alumina stability towards thermal sintering. Promising method of oxides preparation, very interesting and simple but not sufficiently studied yet is a mechanochemical synthesis. Here we report on the synthesis of nano-sized alumina, ceria and ceria-alumina of various compositions by a wet solid phase mechanochemical reaction of hydrous aluminum, and/or cerium nitrate with ammonium bicarbonate after addition of a small amount of water. The aim of this contribution is to study processes being in progress during synthesis of the mixed oxides, interaction between components and their mutual effect on the properties of resulting products. The phase evolution during mechanical milling and the subsequent heat treatment of precursors were studied by X-ray diffraction, DTA/TG, H2-TPR, NH3-TPD, CO2-TPD, N2 adsorption at -195°C, IR, and XPS spectroscopy. Alumina and mixtures of alumina with different quantities of CeO2 (1- 18 wt. %) were synthesized by mechanochemical method from aluminum nitrate, cerium nitrate and ammonia bicarbonate.
Fulltext: content.csg -  PDF
Plný tet: SKMBT_C22015083108560 - PDF
|
|
Doped DLC coatings for biomedical applications
Písařík, Petr
Nowadays there are materials having excellent properties for use in medicine (Diamond-like carbon, Hydroxyapatite, …). Diamond-like carbon (DLC) is a metastable form of amorphous carbon containing bonded carbon atoms of sp2 and sp3 hybridized orbital. DLC layers are semiconductors with high mechanical hardness, chemical inertness, low coefficient of friction, high thermal conductivity, good electrical and optical properties, biocompatibility and no cytotoxicity. All properties of the films are not always ideal, so it is necessary to modify the layer. One example of how to modify the properties of thin layers are dopations. The incorporation of dopants in films may lead to greater multifunctionality and much improved properties. Most modifications were made to modify contact angle and surface energy, to reduce internal stresses, to decrease surface roughness, coefficient of friction or wear....
|
|
How to prevent the proliferation of Legionella pneumophylis in hot water in the hospital Czech Krumlov
TUREK, Jan
This diploma thesis deals with microbiological quality of hot water in a hospital in Cesky Krumlov as well as hot water piping condition with respect to Legionella. It also deals with arrangements for improving the quality of hot water in this hospital. The subject and target of this thesis are the findings of the mentioned parameters based on own observations, technical documentation and analysis of warm water performed by an accredited laboratory. The hospital in Cesky Krumlov, the construction of which began in 1909, was built in 1911 as the 'Nemocnice Císaře Františka Josefa I.' As the time went by, new buildings were built up. The hospital was renamed to 'Všeobecná veřejná nemocnice' in 1942. In the following years the hospital expanded until the current condition. Water quality and presence of Legionella is a world-wide issue, which we must fight against. The thesis is divided into two parts. First, theoretical part, which includes both general and specific knowledge about Legionella, its health risks, the environment in which it occurs, possibilities of eliminating, suitability of the material for hot water pipes, gained in professional literature and a part of the Czech legislation dealing with public health protection, the law 'No. 258/2004 Coll.' in actual version and quality of drinking water and hot water. In the second, empirical part, I focus on the situation of the hospital in Cesky Krumlov from 2009 till 2015, concerning newly built boiler room and the whole distribution system of hot water regarding Legionella. Particularly I focused on materials used for ecologisation of the gas boiler room and materials used for hot water pipes and actual state of water distribution in individual buildings of this health care facility. I mentioned the analysis of the water samples performed by an accredited laboratory with corresponding technical documentation, which concerns the water distribution system, provided by the medical facility. I used secondary data analysis to evaluate these documents. Regarding the results from 2009 to 2015 the microbiological quality of warm water doesn't meet the limits defined in the Attachment No. 3 of the above mentioned law Order 252/2004 Coll. Limit value for colony forming units of Legionella is set to maximum of 100 CFU. In most of the samples this limit was exceeded by series of units up to hundred thousands of units. The last results in 2015 prove improvement of the unfavorable situation. In that year the analysis was tested three times. First in February, where the CFU units were 'only' in hundreds, with the top value of 550 CFU in the Postacute Care ward. Second analysis was performed in June that same year. Results were acceptable. The highest value was 64 CFU. Last analysis in the hospital was performed in December. Increased concentration of Legionella was again in the Surgery building. There were established of 1400 colony forming units. There were 300 CFU in the Postacute Care ward and the limit value of 100 CFU was in the ward of Internal medicine. The answers to research questions 'How to prevent reproduction of Legionella peumophylis in the water distribution system of the hospital in Cesky Krumlov?' and 'How to ensure a sufficient amount of quality hot water in the medical facility?' are included at the end of the stated recommendations. A risk factor causing the fast reproduction of Legionella is the old water distribution system in most of the buildings and low water temperature of water leaving the boiler, which is 55°C. All mentioned results and evaluations are included in this thesis as well as attached pictures, which show the environment and situation within the Health Care Institutions.
|
|
Effect of sex on growth and formation of dorsal muscle of pigs
Fáberová, Gabriela ; Čítek, Jaroslav (advisor) ; Zadinová, Kateřina (referee)
Effect of sex on growth and formation of dorsal muscule of pigs Summary The aim of this thesis is to determine the influence of gender on the growth and formation of the pigs dorsal muscle. Growth is one of the basic phenomenon characterizing living organism. Is a creation of nonliving to living matter. The amount of body mass is not constant through the life, it is changing significantly. In the early postnatal period is skeleton growing faster compared to muscles and fat then leads to faster growth of muscle and in the last period called maturity to the fattening. Evaluating growth has a significant gender effect. In case of pigs, it is common to feed barrows and gilts. Nowadays it begins to think about feeding of boars or the imunocastrates. Due to different hormonal activities we can expect different muscle and fat deposition. The task of this study was to clarify the influence of gender on the formation and growth of pigs dorsal muscle. There were 72 pigs tested in total. Pigs were housed in pairs in cotes and divided by gender for pigs, boars, imunocastrates and sows. This subpopulation of genotype DanBred animals were divided to 1/4 (18ks) uncastrated male pigs (K) 1/4 (18ks) hormonally castrated male pigs (I), 1/4 (18ks) barrows (V) and 1/4 (18ks ) gilts (P). Average live weight of pigs at the start of the trial was 28.5 kg, while the test was conducted to average 107 kg bodyweight. Through all time pigs were fed ad-libitum KKS. During the test it was monitored at weekly intervals individual live weight, back fat thickness at A, B, muscle depth at A, B and the total percentage of muscle for all categories of pigs. The obtained results show that the growth and formation of a long dorsal muscle are influenced by gender. When comparing the weight in a given period, we conclude that during the time the difference between gilts and imunocastrates grow up. Best growth had imunocastrates gilts similarly, only was there an earlier stop of the growth. The highest increase in fat and muscle measured at the A and B, occurred in pigs, in sows we can see increasing gains in fat with respect to the period in which they are fattening. Boars had the lowest backfat thickness, imunocastrates. With imunocastrates we evaluate low fat increase compared to the beginning of the observation. The biggest muscle depth measured at A and B had the barrows with gilts and imunocastrates and especially boars did not reach the values as barrows and gilts, who had the highest muscle depth. Biggest % of muscle was measured in sows. A large proportion of muscle can be seen in male pigs. The proportion of muscle mass of imunocastrates was under the average and worst ratio of muscle had especially at the end of feeding barrows indicating that with increasing age there is a significant fattening, compared to the remaining groups of pigs Keywords: pig, growth rate, muscle fibers
|
guest ::
