|
|
Determination of mechanical properties of light metals and alloys and composites via small punch test
Langer, Jiří ; Dobeš, Ferdinand (referee) ; Válka, Libor (advisor)
The aim of diploma thesis is estimate mechanical properties (yield strength, maximum strength and elongation) of light alloys by means of SPT. For the experiments were selected aluminium alloys (Al 2024, Al 6082 T6, Al 7020 and NASA 398) magnesium alloys (MgZnMn, AZ31, AZ61) and composites (AZ91 + 20 % saffilu a Al + Al4C3). Theoretical part of this thesis is focused on analysis of conversion formulas, which were made from SPT data and conventional testing. Experimental part is dedicated to evaluation of experimental data and critical analysis validity of conversion formulas. In this part of thesis is discused the problematics of reproducibility methodology of SPT.
|
|
|
Optimalization of parts bonded by hot crimping
Liškář, Ladislav ; Řiháček, Jan (referee) ; Lidmila, Zdeněk (advisor)
The thesis describes the procedure for verifying the conceptual ideas of the company. Design and production of prototypes, testing and evaluation, quantifying savings. Two variants of crimped bond were chosen. For each was length of shaft changed to three and four crimped grooves. These prototypes were tested in two static and one dynamic tests. Recommendation for company is continue with other phases of development for shaft with four grooves.
|
|
| |
|
|
Comparison of tensile properties of polymeric samples produced by extrusion based 3D printing
Krajcar, Ivo ; Vespalec, Arnošt (referee) ; Škaroupka, David (advisor)
The subject of this work is a summary of the contemporary knowledge about 3D printing and mechanical properties of a prototype manufactured this way. Main goal is to compare the frequently used FDM method with the innovative APF method of 3D printing from the Arburg company. ASA and CPE materials were chosen for researching this method. On these materials, tensile strength was measured. Aditionally, for comparison between the two methods, referential samples manufactured by injection moulding were made. A percentual difference in strength of each sample was compared against these. 60 samples in total were made for this comparison. After evaluation of the results, it was found that in the tensile strength the samples made by the APF method are approximately 30 % less strong than the referential sample. The samples made by the FDM method are approximately of the same strength as the referential sample.
|
|
|
Development of process parameters for the stereolithography
Vítek, Jan ; Škaroupka, David (referee) ; Paloušek, David (advisor)
This bachelor thesis deals with the search for optimal process parameters to reach a high strength of the Detax Solflex model material, with the DLP (digital light processing) 3D Solflex 650 printer. In the first part of this thesis the principle of printing using a laser and using a DLP projector and their comparison are presented. Further information about materials and impact of the process parameters on a printing are discussed. Based on a knowledge two assumptions were set: influence of exposure time and influence of layer thickness on strength. Firstly, samples were tested by the hardness Shore D test and the results from the test were compared. New samples for the stress test with the optimal set of parameters given by the previous test were printed and tested. Process parameters influence on strength was determined from the achieved results.
|
|
|
Influence of Homogenizing on Mechanical Properties of AZ91 Alloy
Provazníková, Andrea ; Liškutín, Petr (referee) ; Věchet, Stanislav (advisor)
This bachelor thesis includes photos and graphic representations of the influence of heat treatment on the mechanical properties of magnesium alloy AZ91. The structures of the alloy are recorded on the light microscopy pictures as well as photographs taken using a scanning microscope of fracture areas in the material. Results of a Tensile Test determining the strength and plastic properties and measuring of hardness and microhardness of the material are also included.
|
|
|
Possibilities of the description of stress-strain curves for computational simulations
Košťál, Josef ; Halabuk, Dávid (referee) ; Šebek, František (advisor)
Tato bakalářská práce se zabývala problematikou určování křivky zpevnění (taktéž „flow curve“) z experimentálně změřených výstupů tahové zkoušky a regresí této zjištěné křivky nelineárními vztahy. Byl prezentován teoretický základ zkoušky tahem a jejího výstupu a také byly popsány rozdíly mezi smluvním a skutečným napětím a přetvořením. Dále byla zmíněna analytická korekční metoda (Mirone-La Rosa) pro odhadnutí trendu křivky zpevnění. Tato metoda využívá standardních výstupů tahové zkoušky. Dále byly vypsány elasto-plastické po částech spojité materiálové modely, a navíc byly vybrány a detailněji rozebrány 4 nelineární vztahy pro popis křivky – Hollomon, Ludwik, Swift a Voce. Následně byla použita metoda konečných prvků pro určení a zkalibrování křivky zpevnění oceli 18CrNiMo7-6, změřené tahovou zkouškou. Pouze standardní výstup tahové zkoušky byl potřeba pro kalibraci. Křivka zpevnění byla zkalibrována iterační výpočtovou metodou na základě srovnání reakční síly ze simulace se silou z experimentu. Nakonec bylo vytvořeno uživatelské prostředí pro nalezení nejlepší regrese ze čtyř vybraných nelineárních vztahů.
|
|
|
Tension - compression asymetry non-ferous alloys
Čavojec, Martin ; Judas, Jakub (referee) ; Zapletal, Josef (advisor)
Bakalářská práce se zabývá asymetrickou odezvou na tahové a tlakové zatěžování neželezných kovů, jmenovitě hořčíkových slitin. Popisuje základní problematiku zkoušek tahem a tlakem, experimentální stanovením asymetrické odezvy, vliv rozličných parametrů na asymetrickou odezvu na tahové a tlakové zatěžování, a také možný popis asymetrie jako funkci orientace a textury. Na závěr práce popisuje experimentální stanovení a vyhodnocení asymetrické odezvy na tlakové a tahové zatěžování hořčíkové slitiny AZ61, s metalografickou analýzu tyto slitiny.
|
|
|
Analysis of Mechanical Properties of Bimetallic Materials with Clad Layer of Inconel
Sýkora, Milan ; Joska, Zdeněk (referee) ; Sedlák, Josef (advisor)
This diploma thesis deals with the analysis of mechanical properties of bimetallic materials with clad layer of Inconel. In the theoretical part of the work there is an analysis of the investigated bimetallic material. The following is a description of mechanical tests and methods for evaluating the integrity of the surface, which were used to determine the properties of bimetallic material. The experimental part focuses on individual tests of mechanical properties of the material. For each test, the procedure for the production of test specimens, a description of the test equipment, the performance of the tests, the evaluation of the data obtained and finally, the evaluation of the results obtained are given.
|
|
|
Structural and Mechanical Characteristics of Nickel-Alloyed Ductile Cast Iron
Tesařová, Hana ; Kohout, Jan (referee) ; Kruml, Tomáš (referee) ; Konečná,, Radka (referee) ; Pacal, Bohumil (advisor)
The aim of this dissertation work is the evaluation of the influence of nickel alloying on the structure and mechanical properties, both monotonic and dynamic, of nodular cast iron with ferritic and bainitic matrix. Two chock melts with 0.5 and 2.7 % Ni were used to study the nickel influence. The quantitative evaluation of structure of these melts using image analysis was done and basic tensile mechanical properties were determined. Subsequently, the time optimization of two-stage ferritic annealing and isothermal austempered heat treatment at 375 °C was performed with the aim to obtain optimal ferritic and bainitic structures with best static and dynamic mechanical properties. After ferritic annealing the nickel alloying contributes to substitution hardening of ferritic matrix which positively affects its strength and other mechanical properties. The higher nickel content in the bainitic structure causes the shift of phase transformation times to longer times which results in restricted production of small carbides and in bigger volume of retained austenite. These features were confirmed by observation in transmission electron microscope. Precise tensile and low cycle fatigue tests at temperatures 23 and – 45 °C were performed on the optimized structures of both nodular cast irons. As a result of the notch effect of graphite nodules, microplastic deformation of both nodular cast irons was observed at stresses which were lower than the yield stress. The Hollomon's equation very well describes the individual parts of tensile curves for both nodular cast irons including their mutual comparison. From the low cycle fatigue tests, the cyclic hardening/softening curves, the evolution of elastic modulus and hysteresis loop shape parameters, cyclic stress-strain curves and fatigue life curves were obtained for both temperatures and materials. Moreover, the decrease of retained austenite volume was measured by neutron diffraction and the evolution of surface relief was characterized during cyclic straining for both austempered nodular cast irons at both temperatures. On the basis of these results both cyclic plasticity and fatigue degradation mechanisms in relation to the cyclic strain localization were described for both nodular cast irons.
|
guest ::
