|
|
European emission legislation
Rytina, Matěj ; Kučera, Pavel (referee) ; Píštěk, Václav (advisor)
The aim of this bachelor thesis was to write about exhaust emissions and their influence on environment, briefly sum issue of emission standards up and mainly sum existing facts about the “Dieselgate” affair up. I wanted to objectively evaluate this issue in my bachelor thesis. Asset of this thesis was mend to be in fact that this affair has not been academically covered yet.
|
|
|
Re-design of biomass boiler for very wet fuel
Zbořil, Martin ; Skála, Zdeněk (referee) ; Lisý, Martin (advisor)
The aim of this thesis is to calculate the stoichiometric balance of boilers and boiler fuel for normal monture to 60%. Determine the monture, content depending on the conditions of the fuel in the combustion chamber and conditions of combustion. Experimental analysis of the current state of the boiler ZKG measurements using this device and propose modifications and solutions.
|
|
|
Technology of Selective Catalytic Reduction
Kudlík, Michael ; Janoušek, Michal (referee) ; Dundálek, Radim (advisor)
This bachelor thesis is focused on technology of selective catalytic reduction. The technology was created as a result of introduction of strict emission limits which manufacturers with this technology reach. First part of this thesis deal with the composition of the exhaust gases, where are dismembered the various elements, and then are given here the European emission limits.Then is thesis focused on ways of reducing emissions of diesel engines which describes the function of exhaust gas recirculation and a function of selective catalytic reduction. Then are described development systems selective catalytic reduction. The conclusion consists of the use and application of Automobile Manufacturers.
|
|
|
EURO 6 Emission Standards
Velešík, Aleš ; Prokop, Aleš (referee) ; Dundálek, Radim (advisor)
Bachelor´s thesis is focused on the approach the issue of Euro 6 emission standards. There is a general description of the tests, which the manufacturer must undertake and successfully complete to produce cars at this emission level. There is also a description of the harmful substances produced from the exhaust system of a car and an overview of the structural elements to reduce them. In conclusion, the reflection on the issue of emission standards and their constant tightening.
|
|
|
Analysis of flue gas in automatic domestic boilers for agropelet
Minář, Marek ; Lisý, Martin (referee) ; Jecha, David (advisor)
The objective of the presented bachelor thesis is flue gas analysis during combustion of agropellets in automatic household boilers. Emphasis is placed on the description of biomass as a fuel, the ways of using biomass for energy purposes, alterations of biomass, production and properties of alternative pellets, automatic boilers and burners for combustion of specific fuel types. The end of the theoretical part is focused on standards and regulations for boiler operation. The practical part verifies the formation of emission on small sources of pollution and determines the concentration of solid and gaseous pollutants. The end of the practical part pursues with comparison of results with legislative requirements and calculation of boiler efficiency.
|
|
|
The DPF and SCR systems
Novodomský, Tomáš ; Janoušek, Michal (referee) ; Dundálek, Radim (advisor)
The presented bachelor thesis deals with exhaust emission reducing systems for diesel engines. The first part is devoted to the composition of exhaust gases and emission standards. The thesis analyses the formation of solid particles, their regulation by the DPF system and its various variants. Further the principle of reducing the nitrogen oxide content in the exhaust gases by the selective catalytic reduction system is described. In the final part, there is a reflection on the future of emission reduction systems, emission standards and alternative drives.
|
|
|
Application of Pressure Accumulator Injection System on CI Engine
Šiška, Adam ; Štěpánek, Karel (referee) ; Dundálek, Radim (advisor)
This master’s thesis deals with building the most modern injection systém Common-Rail for four-cylinder tractor diesel engine. The following application is a conversion from a obsolete system with inline injection pumps. Because the costs for this conversion must be minimized, that it is effort of minimal intervention in engine design. First this master’s thesis focuses on the theory of injection systems of diesel engines and related things and then the thesis shows the design conversion supported analytical calculations and FEM analysis of newly designed components.
|
|
| |
|
|
Determination of CO2 exhaust emissions for CNG, petrol and diesel vehicles
Chytil, Ivo ; Libich, Jiří (referee) ; Bača, Petr (advisor)
The thesis deals with the topic of Carbon dioxide emissions that are created by Petrol, Diesel and CNG vehicles. In the first part of the thesis, the results of theoretical calculations are compared with the values of the manufacturer of the specific vehicle. In the second part, a specific method has been selected for calculations with real data from transport. The savings of CO2 produced by the specific vehicle are expressed in percentage – depending on the fuel used. The operating expenses from the real data are calculated and compared with hybrid and electric vehicles. In the final part of the thesis, the ratio of fleet type vehicles to the financial/ecological aspect was proposed.
|
|
|
Optimization of Gases Flow in Exhaust System of Tractor Engine
Létal, Filip ; Svída, David (referee) ; Dundálek, Radim (advisor)
The subject of this thesis is to optimize the flow of exhaust gases in the particle filter using CFD simulations. The first part is focused on the emissions of diesel engines and emissions reduction systems with a focus on particulate filters. The next section is an analysis of the current state of the specified particle filter using CFD simulation and evaluation following with a proposal of new construction for better flow distribution. At last, the final evaluation is presented.
|
guest ::
