| |
|
Využití prvků arteterapie u žáků ve střední speciální škole (praktické)
Koubská, Patricie ; Valešová Malecová, Barbara (vedoucí práce) ; Šiška, Jan (oponent)
Využití prvků arteterapie u žáků ve střední speciální škole (praktické) Tématem bakalářské práce je využití arteterapeutických postupů u žáků z praktické dvouleté školy. Cílem práce je posoudit možnosti využití prvků skupinové arteterapie k rozvoji sebepoznání, komunikace, k posílení prosociálních vazeb a zvýšení pocitu skupinové sounáležitosti. Arteterapie je zde pojímána v užším slova smyslu jako terapie výtvarným uměním. Teoretickými východisky práce budou metody arteterapie, jejich možnosti a postupy, vývojové aspekty dospívání, specifika dospívání u žáků se znevýhodněním (problematika mentální retardace, specifických poruch chování, problematika žáků se sociálním znevýhodněním, se zdravotním znevýhodněním). V praktické části práce popisuji využití těchto metod v hodinách výtvarné výchovy.
|
|
Coarse-grained particles conveying along a pipe bed
Vlasák, Pavel ; Chára, Zdeněk ; Konfršt, Jiří ; Kysela, Bohuš
The paper describes the results of a flow visualisation of model coarse-grained fully stratified particle-water mixtures. Investigation was focussed on study of the particle behaviour and carrier liquid and conveyed particles local velocities. Glass balls and washed graded pebble gravel of mean diameter of 6 mm were conveyed by water in a horizontal smooth pipe loop with a transparent pipe viewing section of inner diameter 40 mm. Particle movement along the pipe invert and particulate stationary bed, created by two layers of spherical particles of the same size as the conveyed particles, was studied. The effect of stationary bed on local velocity values of the carrier liquid and conveyed particles were determined. It was conducted that the maximum liquid velocity is significantly shifted from pipe centre to a higher position in the flow pattern with stationary bed.
|
|
Vliv poklesu cen ropy a zemního plynu od roku 2014 na katarskou ekonomiku
Šamánek, Ondřej ; Stuchlíková, Zuzana (vedoucí práce) ; Hasík, Gabriel (oponent)
Bakalářská práce se zaobírá vlivem pádu cen ropy a zemního plynu, který postihl svět v červnu roku 2014, na ekonomiku Kataru. Hlavním cílem práce je zjistit, jak a do jaké míry pokles cen zmíněných komodit ovlivnil ekonomické ukazatele a chování státu i jednotlivých firem operujících v postihnutém odvětví. Zvolený problém je řešen pomocí metody časové komparace, u níž jsou hodnoty relevantních ekonomických ukazatelů porovnány před a po krizi, či vypracovanou případovou studií, u které je situace analyzována na příkladu katarské firmy operující v postiženém odvětví. Ze zkoumání vyplývá, že pád cen ropy a zemního plynu na ekonomiku Kataru vliv měl. Země se rok po snížení cen potýkala se snížením HDP či propadem rozpočtového salda, postižená firma v odvětví zase vykazovala pokles počtu udělených zakázek či rekordní množství zrušených výběrových řízení. Závěry z práce vyplývající lze do jisté míry užít i na ostatní ropné exportéry Perského zálivu, kteří s Katarem sdílejí podobné rysy.
|
|
Comparison of Diffusion Coefficients in Initial Stages of Mutual Diffusion in Layered Structures Carbon/Ferrite and Carbon/Austenite for Chosen Alloys
Čermák, Jiří ; Král, Lubomír
Coefficients of mutual carbon diffusion were measured at initial stages of diffusion for surface thin layer of carbon/ferrite and carbon surface layer/austenite. The aim of the study was to compare the diffusion characteristics obtained at the present strongly non-equilibrium case with those known for carbon mutual diffusion in cases where the carbon concentration does not exceed the solubility limit in the respective substrate. The second goal was to judge, whether the carbon diffusivity is determined by the structure of the substrate matrix (BCC or FCC). As examples of ferrite substrate, pure Fe and chromium steel P91 were chosen, as an example of austenite substrate, AISI316 was taken. It was obtained that – similar to nearequilibrium case – the carbon diffusion measured close to interface C/austenite is significantly lower compared to carbon diffusion near the C/ferrite. Values of carbon diffusion coefficients in cases C/Fe and C/P91 are close one to another. All carbon diffusion coefficients are much lower than those, reported for near-equilibrium conditions; they approach values measured in carbides.
|
|
Changes in structure and phase composition in the surface of tram rail
Švábenská, Eva ; Roupcová, Pavla ; Schneeweiss, Oldřich
We have investigated structure and phase composition of surface layer of tram rails after long time running and the results were compared with those obtained on the original part of material. Changes due to effects of severe plastic deformation together with thermal shocks by friction process were expected. The information about structure and phase composition was obtained by optical and scanning electron microscopy, X-Ray Powder Diffraction, Mössbauer Spectroscopy and Glow Discharge Emission Spectroscopy (GDOES) and this was completed by microhardness measurements. The results show that the surface layer in comparison with the original material exhibits important changes in grain structure, an increase in microhardness and high content of iron oxide and hydrooxides. According to the depth profile of the chemical composition measured by GDOES there is an increase in carbon content in the surface layer which can be effect of up-hill diffusion.
|
|
STRAIN ENGINEERING OF THE ELECTRONIC STRUCTURE OF 2D MATERIALS
del Corro, Elena ; Peňa-Alvarez, M. ; Morales-García, A. ; Bouša, Milan ; Řáhová, Jaroslava ; Kavan, Ladislav ; Kalbáč, Martin ; Frank, Otakar
The research on graphene has attracted much attention since its first successful preparation in 2004. It possesses many unique properties, such as an extreme stiffness and strength, high electron mobility, ballistic transport even at room temperature, superior thermal conductivity and many others. The affection for graphene was followed swiftly by a keen interest in other two dimensional materials like transition metal dichalcogenides. As has been predicted and in part proven experimentally, the electronic properties of these materials can be modified by various means. The most common ones include covalent or non-covalent chemistry, electrochemical, gate or atomic doping, or quantum confinement. None of these methods has proven universal enough in terms of the devices' characteristics or scalability. However, another approach is known mechanical strain/stress, but experiments in that direction are scarce, in spite of their high promises.\nThe primary challenge consists in the understanding of the mechanical properties of 2D materials and in the ability to quantify the lattice deformation. Several techniques can be then used to apply strain to the specimens and thus to induce changes in their electronic structure. We will review their basic concepts and some of the examples so far documented experimentally and/or theoretically.
|
| |
| |
|
ELECTRON BEAM REMELTING OF PLASMA SPRAYED ALUMINA COATINGS
Matějíček, Jiří ; Veverka, J. ; Čížek, J. ; Kouřil, J.
Plasma sprayed alumina coatings find numerous applications in various fields, where they enhance the properties of the base material. Examples include thermal barriers, wear resistance, electrical insulation, and diffusion and corrosion barriers. A typical structure of plasma sprayed coatings, containing a multitude of voids and imperfectly bonded interfaces, gives them unique properties - particularly low thermal conductivity, high strain tolerance, etc. However, for certain applications such as permeation barriers or wear resistance, these voids may be detrimental.\nThis paper reports on the first experiments with remelting of plasma sprayed alumina coatings by electron beam technology, with the purpose of densifying the coatings and thereby eliminating the voids. Throughout the study, several parameters of the e-beam device were varied - beam current, traverse velocity and number of passes. The treated coatings were observed by light and electron microscopy and the thickness, structure and surface morphology of the remelted layer were determined and correlated with the process parameters. Based on the first series of experiments, the e-beam settings leading to dense and smooth remelted layer of sufficient thickness were obtained. In this layer, a change of phase composition and a marked increase in hardness were observed.\n
|
host ::
