| |
|
Methods of Technical Diagnostics
Klusáček, Stanislav ; Ďaďo, Stanislav (referee) ; Němec, Zdeněk (referee) ; Tůma, Jiří (referee) ; Bejček, Ludvík (advisor)
The main objective of the presented thesis is to contribute to the development of diagnostic methods for piezoelectric sensor testing. The thesis describes the methods for piezoelectric sensors microcracks identification and diagnostics. The core of the thesis presents the development of a knock sensor prototype, design of suitable methods for the knock sensors diagnosis and evaluation of developed methods with focus on detection of microcracks in the sensor piezoceramic. The last part of the thesis deals with the influence of cracks and splits on the measured data from the piezoelectric transducer. The presented methods are focusing on impedance measurements and sensors frequency response measurements. Known properties of used piezoelectric material as an information source for measurement and diagnosis are provided. The main result of the work is the evaluation of the methods developed for the piezoelectric sensors self-diagnosis.
|
|
Use of VAG-COM PROFI Diagnostic Kit in Forensic Engineering
Wertheim, Adolf ; Tylšar, Vladimír (referee) ; Panáček, Vladimír (advisor)
The thesis deals with possibilities of application of VAG-COM PROFI diagnostic kit in forensic engineering. After defining a theoretical basis, according to possibilities of evaluation of technical condition of a vehicle, the thesis is focused on applying diagnostic methods using above mentioned diagnostic kit. With respect to opportunities of identification of driving parameters, possibility of acceleration measurement and estimation of engine power are introduced. Describing of methodology and making the final statement are contained in the thesis as a part of every single measurement.
|
| |
|
Safety of technological systems
Jiříček, Petr ; Pavlík, Josef (referee) ; Hammer, Miloš (advisor)
The work deals with the safety of technological systems and can be divided into two main thematic units. The attention in the first theoretic unit is paid to aspects that affect the safety of technological systems during their technical life. It describes, together with elementary norms and acts solving the products safety, the most important principles for creating and analysing the safety. It clarifies the origin of company’s risk management, part of its quality management, mentions the faults in which products can be found and also describes the failures which have the biggest effect on these faults and of course on the safety too. Attention is further paid to the reliability analysis, as the tool that helps to create the products safety in the pre-manufacturing phase and also to technical diagnostic, as the tool to keep the safety in after-manufacturing phase. The second practical unit arithmetically analyses the safety of two high-voltage transformers. For that it was used the database of real operation numerical values that were gained during diagnostic investigations on these transformers. In addition it describes mentioned diagnostics methods and gives the new procedure for analyse of transformers’ safety by criteria matrix and weighted sum approach. The main contribution of the work can be considered the checkout and the evaluation of this procedure for use in elaboration of high-voltage transformers diagnostic values for analyzing their safety.
|
|
Bearings Error Frequencies
Životský, Petr ; Pata, Vladimír (referee) ; Zuth, Daniel (advisor)
This dissertation deals with error frequences of bearing because the bearing is part of every rotary machine. Certain type of bearing and caused defect is being compared with error frequences which are acquired by experiment. Various kinds of measurement which are more or less applicable in use are being described. Further the dissertation deals with other possible ways of detection error frequences for particular defects of bearing.
|
|
Design of the control device for vibrographic measurement
Weiss, Lukáš ; Čožík, Ondřej (referee) ; Levek, Vladimír (advisor)
This diploma thesis deals with designing of the control device for vibrographic measurement. The device is primary used in cooperation with MERCURY Real Time Tracking System. The main task of the device is time-controlled triggering of camera system. In the first step, the summary of basic information about technical diagnostic and vibrodiagnostic is reported. The second part describes vibrodiagnostic measurements with MERCURY system. The third part describes a hardware design of the device and functional blocks and its parameters. Next part provides a simple algorithm of the device operation and a communication protocol. Last part contains measured data of the realized device and vibrographic measurement with laboratory sample.
|
| |
| |
|
Machine service and diagnostics with a focus on agricultural machinery
SVOBODA, Bohuslav
The introduction provides basic diagnostic procedures and methods in the measurement of diagnostic indicators. The following describes the techniques used in diagnosis and technical principles for correct measurements made in the repair of vehicle systems. The paper deals with the ways of restoration of damaged parts. Finally, we set the new drive technology vehicles such as hybrid drives.
|