|
|
Optimalization of Induction Furnace Operation in foundry Vsetín
Trachta, Jiří ; Nowak, Stanislav (referee) ; Lázničková, Ilona (advisor)
The aim of this work is optimalisation of induction furnace in foundry for company PROMET FOUNDRY a.s. The company has two induction furnances. There are installed as identical construction. They have 2 modes of operation. First mode is founding and second mode is mode, where is temperature in maintain mode. Only one induction furnance can work in the founding mode at a time though. Inducion furnances are in the single-phase connection and they cause unbalance in the distribution network. Near the foundry there is a small network area whitch it is operated by company Zásobování teplem Vsetín a.s. The consumption of electrical energy in foundry so big, that in the year 2009 was made elaborate for Zásobování teplem Vsetín a.s. It was write at Laboratoře diagnostiky výkonů (Laboratory of performance diagnostics), which is a part of Electrotechnic Department at Technical Univarsity of Ostrava. The ordered study was named “Verification of causes of increased reactive energy consumption during transition from electricity delivery to electricity consumption”. The conclusion of this assignment confirms that in distribution network in the Jiráskova area in Vsetín there is unbalance of electrical energy and there is high part of reactive power. The next conclusion is crucial to find the customer who made the unbalance and to set relevant remedy. The last step will be the identification whether such device can actually be effectively balanced. It was subsequently proved that the Promet Foundry was causing the unbalance and that balanced consumption would be reasonable. Promet Foundry thus addressed Autel a.s. company with an inquiry to make a study of removing the causes of the unbalance which is caused by current induction furnaces operation at a minimum possible cost, least possible influence on the performance and minimum construction changes concerning the building. In this thesis there will be some topics. The result of which will be introducing of used heating technology, introducing of company and of effective plant performance and subsequent suggestions of possible unbalance removal or reactive power decrease. Several ways which are being implemented in the industry in order to balance consumption will be described. A suitable balancing plant will be subsequently chosen and its parameters will be calculated.
|
|
|
Intelligent lightning system
Harman, Ján ; Šír, Michal (referee) ; Bradáč, Zdeněk (advisor)
The aim of my master’s thesis is a system for control of the light intensity. It is electronic equipment which controls the intensity of the light circuits based on settings and input signals. This equipment could work on single-phase systems or multiphase systems. The equipment is controlled by the signal DMX-512 which is a standard for the control of lighting technologies. The set up of this equipment is based on a personal computer or in a limited form by a small connected display.
|
|
|
Single-Phase Induction Motor Calculation
Ševčík, Pavel ; Vítek, Ondřej (referee) ; Hájek, Vítězslav (advisor)
This master's thesis considers by single-phase asynchronous motor. The first part discuss about construction, principle of operation and basic parameters of this motor type. It also discussed the emergence of torque and torque characteristics of the different types of engines. The second part explains the basic ways of obtaining grip moment including outline the principles of functions particulars constructions types, which is produce in practice. In the third part is minutely analyse single-phase asynchronous motor with auxiliary phase and permanently conect capacitor, including method of assign size of a capacitor. Fourth part section provides the principles of the procedure for calculating basic parameters of the single asynchronous motor with auxiliary phase. At the last part is accomplished a calculation of single-phase asynchronous motor with permanently conect capacitor at auxiliary phase including comparation with already manufacturing motor.
|
|
|
HP89410A User Interface
Neužil, Jan ; Caha, Luděk (referee) ; Beneš, Petr (advisor)
The aim of this thesis was to develop user interface in LabVIEW to make typical measurements with spectral analyzer HP89410A There is introduced the theory of operation of an analogue heterodyne and a digital FFT spectral analyzer. It is explained the background of the Fast Fourier Transform. There are discussed the key settings in measuring with FTT analyzer, like window function, bandwidth, number of frequency points, or the averaging. Further is described the program, which was developed for measuring frequency characteristic by white noise and by stepped measurement. It was also made a module for measuring Signal to Noise Ratio and module for Total Harmonic Distortion. In the last part of this thesis are shown the results of processed exemplar measurements.
|
|
|
The influence of cobalt additive on parameters of positive electrode for Ni-Cd accumulators
Svoboda, Michal ; Svoboda, Vít (referee) ; Špičák, Petr (advisor)
The Master´s thesis deals with description of the influence of cobalt additive on positive electrode parameters for Ni-Cd accumulators. Trough the use of Electrochemical Quartz Crystal Microbalance are analysed the effects which decline effective life of positive electrode during accelerated cycling. Theoretical part describes important characteristics of Ni-Cd accumulators, the working principle and effects which are in progress on positive electrode during cycling. The next part deals with description of system EQCM and the pricnciples of doping active mass with cobalt additive. Practical part consists of EQCM system calibration and electrochemical measurements. The principal aim is detection of the influence of cobalt additve on active mass during cycling in different electrolytes. From the results of measurements is set the optimal amount of cobalt additive.
|
|
|
Modern low-emission combustion chamber for jet engines
Mašek, Jakub ; Nastálek, Ondřej (referee) ; Šplíchal, Miroslav (advisor)
Bachelor´s thesis examines modern low-emission combustion chambers for jet engines. It´s foremost aim is to specify construction parameters of low-emission combustion chambers, compare it´s features and comprise the use of these combustors in civil aviation. Thesis deals with reasons of modern low-emission combustion chamber development and estimate future development in the region of aircraft industry. Another aim is to specify legislations of aviation emissions, history of certification standards and organizations, which make and control these limits.
|
|
| |
|
|
Vibration diagnostics of bearings
Navrátil, Pavel ; Mazal, Pavel (referee) ; Klapka, Milan (advisor)
This bachelor’s thesis introduces the basic principles of vibrodiagnostic methods and their importance for individual fase of bearing’s damage. The selected methods studied are: acoustic emission, SPM (shock pulse method), SEE (spectral emission energy), envelope method, High frequency emission, Crest factor, Kurtosis factor and special method for slow-motion machines Adash Compressed Time.
|
|
|
Analysis of product development in the telecommunications industry
Hofrichter, Jakub ; Bruckner, Tomáš (advisor) ; Jirovský, Lukáš (referee)
The thesis is focused on product development in companies in the telecommunications industry. These companies provide products to end customers. The introductory section lists and describes the basic concepts accompanying the issue. Also described herein is a method for achieving the objectives of the thesis, that is based on personal interviews with specialists in selected telecommunications companies. The first objective is to identify variables affecting success launching a new product to market services. The thesis defines the internal and external factors in the organization. Part of the analysis is to assess the current state of internal RFC, that was unexpectedly during the development of a long implementation period (TTM). The content of this thesis is identification of key factors and their impacts on implementation also unveiling constraints of the development process. These constraints are in the view of issues that prevent better performance of the relevant processes. The third and the main objective of this thesis is based on previous analyses, proposal of improvements that could contribute in the future to better product development. The proposed improvements are consulted with a specialist Demand Management to determine the feasibility and potential benefit in practice. The greatest contribution of the thesis lies in the proposed improvements and their assessment for future implementation.
|
|
|
Analysis and management of a development project
PRANEVSKÝ, Luděk
The aim of the thesis lies in implementation of a complex analysis of partial phases of a developing project including its management. This aim can be achieved by achieving partial aims such as doing an analysis of a developing project as well as doing an analysis of developing activities in České Budějovice region or analyzing a specified developing project "HOUSELOTS {--} Šindlovy Dvory" including the assessment and suggesting a measure. The reason for setting such a goal is in a need to explore a relatively new enterprise activity which is expanding nowadays and affects all of us. It involves building new commercial centres where people go shopping or entertain themselves as well as building flats, single-family houses and grounds for people{\crq}s living. The complex theoretical analysis of a developing project and the analysis of a single implemented project lead to the conclusion that the success of a developer{\crq}s project is first of all dependent on the quality of a choice of a developing project and also on the exact accomplishment of single phases of a project according to its aims set in advance. It is essential to plan all steps of partial phases of a project exactly. To forget or delay any step in a specific phase of a project can affect the final result dramatically. Significant disturbance of surrounding structures may occur in such cases (suppliers, investors/buyers and other cooperative persons) as well as in big financial losses and even quarrels at law.
|
guest ::
