|
|
Multi-span bridge structure
Necid, Miloš ; Brtáň, Stanislav (referee) ; Koláček, Jan (advisor)
I deal with the road bridge near Velké Meziříčí in the thesis. The highway bridge overcomes valley 360 m long and 36 m high. For each course there is a separate super-structure. Each of the support structures converts three stripes of road transport. I do calculation of internal forces both manually and in Scia Engineer. In the thesis is drawings, showing the gradual construction, diagram of prestressing and reinforcement.
|
|
|
Bridge on a ramp in Brno
Diviš, Dalibor ; Pachl, Radek (referee) ; Panáček, Josef (advisor)
Thesis involves designing and analysis of horizontally curved bridge contruction with chamber-shaped profile and oblique side walls. The object is a part of fly-over crossig at VMO Brno. Calculations are according to actually valid standards ( Eurocodes ). Thesis gives a basic look at the problematics of horizontaly curved bridge construction, including solution of prestressing cables´ 3D-tracking with usage of common software.
|
|
|
Thermal characteristics of power conductors
Měrka, Ivan ; Novotný, Jan (referee) ; Orságová, Jaroslava (advisor)
This bachelor’s thesis aims to theoreticaly analyze thermal phenomena in power conductors and construct a simulation of thermal characteristics of conductor under load. First, power conductors and their classification is discussed. Following are elementary information in thermomechanics and ways of heat transfer. Next chapter talks about different ways of cable laying with respect to their steady temperatures and the design of conductor’s cross section. Further chapter focus on unsteady state of the heating conductor, analysis of Van Wormer’s method for acquisition of thermal characteristics and in this method the model for parameterized conductors is based. In conclusion the simulated results are verified and compared to the results of practical laboratory measurement.
|
|
|
Passenger lifts
Galásek, Martin ; Pokorný, Přemysl (referee) ; Škopán, Miroslav (advisor)
Bachelor thesis "Elevators for transportation of persons" is an overview of applied design solutions of the elevator engines, especially in terms of their efficiency, space and economy utilization in various types of buildings. The final part contains a summary of expected trends of elevators’ development with respect to new design elements, automation improvement, modernization and higher requests on safety during a conveyance of persons.
|
|
|
Assemblying effect on cable lines quality
Dočkal, Martin ; Křepelka, Václav (referee) ; Filka, Miloslav (advisor)
In the first part is explained what actually a structured cabling is. Its beginning, from what and why it was created. Its history when at the beginning were applied unbalanced coaxial cables, those were later replaced by balanced cables. In cabling for TVs are still used coaxial cables. Balanced cables are according to type named UTP, STP, FTP, and so on. Whit growing popularity of this type of cabling and its wide spread application was necessary to set some rules, standards, specifications and demands, how to build up the cabling from project to realization. According to these rules is the system built so there are strict rules for length of subsystems and interfaces and the whole appearance of the structure cabling. Next important point is projecting of cabling that is related to the previous points and when it’s finished, we should strictly follow it. With the project is closely connected characteristic of this cabling as attenuations, cross-talks and other transmission parameters which are measured in the practical part. In the second part is spoken about all the parts of which the structured cabling consists - metallic and optical connecting elements and cables. There are also mentioned their mechanical, electrical and transmission features. In the third part is described influence of man on the quality of structured cabling and the most common causes of lower quality and the ways how to prevent this from happening and how to manipulate with cabling not to destroy it. The final (fourth) part considers the measurement. There are measured qualities of metallic wires as the attenuations, delay, cross-talks on the near- and far-end, impedance and resistance. To all the features are mentioned schemes of the measurement on the twisted pairs. The measurement is divided into two parts. In the first part are measured five types of balanced cables of different length, category and damage influencing quality of these cables. In the second part is measured one balanced cable if it’s corresponding with category 5 for that t was made and if it would be possible to use it also for higher category 6. Values are tabularly sorted in tables.
|
|
|
Electrical installation in family home
Pokorný, Marek ; Bátora, Branislav (referee) ; Macháček, Jan (advisor)
The goal of this bachelor paper with the topic " Electrical installation in family home" is to describe laws and public notices that relate to an electrical setting; relevant norms and conditions for a connection to a distribution network (low tension service lines); ways of connections and its location. Furthermore, this paper describes operational conditions, external effects, dimensioning, cabel lodgements and protection (its ways, principles, security and conductor). In a separate chapter low tensinon switch-boards distribution and its instrumentation is covered. Another sphere of this bachelor paper is the field of illumination and lamps. The following chapter deals with sorts of electrical setting (classic, intelligent), low-tension electrical setting (PC distributions), fire and safty electrical setting and audit report elaboration. A practical sample of a electrical installation in family home is shown at the end of this paper
|
|
|
Reconstruction of discharging shakeout machine electric installation
Bednář, Vojtěch ; Blecha, Martin (referee) ; Pazdera, Ivo (advisor)
This Diploma work is concerned with the design of project documentation for discharging shakeout machine electric installation. This work continues in the Semestral project 2 in which the background of a new machine was made. Then, this work deals with the replacement of a switch room with required devices including the design of a new connecting cables and power streams. In the first part, the work deals with the control part of the device and the design of control and signal cables including the product documentation of the device. In the second part, the work deals with the proposal of building electro installation in which a new lighting and its use is described. The last part focuses on the coordination during the realization of a suggested device. In this part, all problems coming from the particular working procedures including a proposal of possible solutions are described. According to the project documentation and following realization, the documentation of final concept reflecting the real status of the device is described.
|
|
|
Toy Store Computer Network Design
Marek, Milan ; Jordán, Vilém (referee) ; Ondrák, Viktor (advisor)
The bachelor thesis is mainly focused on a design of an operational computer network in a toy store branch. The thesis analyse present situation and based to results there is implemented my own solution. The solution must be doable, operational, easily extendable and it must meet investor requirements.
|
|
|
Machinery frame for rewinding electric cable
Palík, Milan ; Kašpárek, Jaroslav (referee) ; Kašpárek, Jaroslav (advisor)
The topic of this thesis is a frame of rewind device of the electric cabels. The main aim is the analysis of the load conditions of the frame and defining figures for those conditions. The method of final elements will be used to check the firmness of the frame followed by the analysis of the particular results. Drawing documentation of the frame set and other parts according to the instructions of head of this thesis are also components of this thesis.
|
|
|
Device for stringing cable on a drum
Polách, Martin ; Pokorný, Jan (referee) ; Kašpárek, Jaroslav (advisor)
The thesis deals with the design of a cable spooling device on a spool drum under different modes of operation of winding. The focus is on the calculation and design part, where the calculations include the functional dimensions of the individual components and the force effects emanating from the load generated during winding. The design part includes the design of the individual components. Finally, an analysis of the selected structural nodes under different winding modes was performed. This work includes drawings containing the overall equipment assembly, subassembly of the weldment frame and shop drawings.
|
guest ::
