|
|
Optimalization of Exhaust Manifold for SI Engine
Prášek, Martin ; Beran, Martin (referee) ; Svída, David (advisor)
The master thesis is focused on optimizing existing or proposal for a new exhaust tracts on the Volkswagen Polo moving series rally-cross A1 division. The car is powered by concern, water-cooled, atmospheric engine capacity 1599 ccm. To achieve the objectives of the lessons are applied as a theoretical nature (analytical calculation), especially the advanced approaches of the software environment from the firm Lotus. Exhaust treatment systems are designed to suit all rules FIA Sports Association.
|
|
|
Optimalization of Induction Furnace Operation in foundry Vsetín
Trachta, Jiří ; Nowak, Stanislav (referee) ; Lázničková, Ilona (advisor)
The aim of this work is optimalisation of induction furnace in foundry for company PROMET FOUNDRY a.s. The company has two induction furnances. There are installed as identical construction. They have 2 modes of operation. First mode is founding and second mode is mode, where is temperature in maintain mode. Only one induction furnance can work in the founding mode at a time though. Inducion furnances are in the single-phase connection and they cause unbalance in the distribution network. Near the foundry there is a small network area whitch it is operated by company Zásobování teplem Vsetín a.s. The consumption of electrical energy in foundry so big, that in the year 2009 was made elaborate for Zásobování teplem Vsetín a.s. It was write at Laboratoře diagnostiky výkonů (Laboratory of performance diagnostics), which is a part of Electrotechnic Department at Technical Univarsity of Ostrava. The ordered study was named “Verification of causes of increased reactive energy consumption during transition from electricity delivery to electricity consumption”. The conclusion of this assignment confirms that in distribution network in the Jiráskova area in Vsetín there is unbalance of electrical energy and there is high part of reactive power. The next conclusion is crucial to find the customer who made the unbalance and to set relevant remedy. The last step will be the identification whether such device can actually be effectively balanced. It was subsequently proved that the Promet Foundry was causing the unbalance and that balanced consumption would be reasonable. Promet Foundry thus addressed Autel a.s. company with an inquiry to make a study of removing the causes of the unbalance which is caused by current induction furnaces operation at a minimum possible cost, least possible influence on the performance and minimum construction changes concerning the building. In this thesis there will be some topics. The result of which will be introducing of used heating technology, introducing of company and of effective plant performance and subsequent suggestions of possible unbalance removal or reactive power decrease. Several ways which are being implemented in the industry in order to balance consumption will be described. A suitable balancing plant will be subsequently chosen and its parameters will be calculated.
|
|
|
Leadership
Jordán, Petr ; Žatecký, Petr (referee) ; Franková, Emilie (advisor)
The diploma thesis focuses on the formulation of the concept of leadership. I would like to analyze what is the essence of the leadership and what forms can be found according to sources available. The comparison with real subjects in the management field shall take place. The thesis outcomes will present recommendations based on survey carried out. These recommendations should contribute to a more effective function of the company hand in hand with more satisfied employees.
|
|
|
Forming machines and tools
Stránský, Luboš ; Peterková, Eva (referee) ; Podaný, Kamil (advisor)
The Bachelor thesis provides a brief overview of the various types of machines and tools used in metal forming. The paper discussed today and earlier used types of machines and tools.The basic types of machines are: a mechanical presses, hydraulic presses, hammers and rotary thermoforming machines. For each type are explained principles, characteristics, advantages and disadvantages.
|
|
|
RF power meter
Hlaváč, Štěpán ; Jedlička,, Petr (referee) ; Drexler, Petr (advisor)
This master’s thesis describes various principles of measurement of electromagnetic waves in a free space and on a line. Used sensors and their real parameters are given for every method. The analysis of protections of high-frequency inputs of measuring instruments is done here and the most suitable method and protections of input for realization are chosen. The analysis of design of secondary protection of high-frequency input is done in this project. The protection of input is realized and measured. The suitable method of measurement is chosen as well as the sensor for measurement of power. The block diagram and circuit diagram of the meter of power are designed. According to designed conception the measuring instrument for measurement of power is realized and its single qualities are measured during the realization. In the final part its precision is measured and the evaluation of results is done.
|
|
|
Bluetooth® Low Energy Vehicle Keyless Entry
Šterc, Filip ; Povalač, Aleš (referee) ; Frýza, Tomáš (advisor)
Tato práce se zabývá návrhem demonstračního kitu bezlíčového přístupu pro vozidla s využitím nejnovějších integrovaných obvodů Bluetooth Low Energy a budičů automobilové sběrnice od společnosti ON Semiconductor. Aplikace umožňuje ruční i automatické odemykání dveří vozidla ze vzdáleného klíče realizovaného chytrým telefonem. Řešení se zabývá detekcí vzdálenosti vzdáleného klíče, bezpečností BLE spojení a komunikací přes automobilovou sběrnici LIN mezi moduly demonstračního kitu.
|
|
|
Leadership
Jordán, Petr ; Žatecký, Petr (referee) ; Franková, Emilie (advisor)
The diploma thesis focuses on the formulation of the concept of leadership. I would like to analyze what is the essence of the leadership and what forms can be found according to sources available. The comparison with real subjects in the management field shall take place. The thesis outcomes will present recommendations based on survey carried out. These recommendations should contribute to a more effective function of the company hand in hand with more satisfied employees.
|
|
|
The engine of a tractor
Mátyás, Attila ; Sedláček, Martin (referee) ; Kašpárek, Jaroslav (advisor)
This thesis deals with the design and selection of a small utility tractor engine unit. The first theoretical part briefly describes tractors with similar weight category, provides an overview of existing tractor brands and their comparison. The second part of this thesis consists of analytical calculations based on the provided parameters of the tractor. Total power will be the sum of the individual power required for the various technical operations during functioning. The last part deals with selecting the suitable engine unit from the available brochures of world manufacturers based on the calculated values.
|
|
|
Monitorng of the photovoltaic power plant
Střípek, Martin ; Kunovjánek, Miroslav (referee) ; Dolenský, Jan (advisor)
This Bachelor work is dealing with theoretical knowledge of Photovoltaic. One of the great advantage of Photovoltaic is inexhaustible resource in long-time period – The Sun. This approach is especially important in todays world when more and more countries are becoming energetically dependent and may run out of fossil fuels. Bachelor work shall introdukce the principle of Photovoltaic, it's practical use for photovoltaic power stations, further it’s classification and types of constructions. The practical part is focused on monitoring the operation of photovoltaic power. Evaluate the instantaneous AC power, the total energy supplied to the network and compared with theoretical values. Bachelor thesis should help in detecting errors that can lead to energy losses.
|
|
|
Step-down converter with variable output voltage in range from 20 to 100 V
Pazourek, Petr ; Šmirg, Ondřej (referee) ; Hanák, Pavel (advisor)
This master's thesis describes the design and the implementation of a step-down converter with variable output voltage for laboratory purposes. In the introduction the basic functions of switching power supplies are shown, flyback, forward and push-pull converters are described, followed by some integrated circuits for power management of converters. The second chapter discusses in detail the design of requested switched power supply, including the calculation of the electronic parts and design of the storage inductor. Following are described some observations of building this power supply, including the output characteristics. In conclusion, the obtained results are assessed, including proposals to improve whole design.
|
guest ::
