|
|
Design of audio power amplifier with Bluetooth connectivity
Bartoň, Jan ; Šotner, Roman (referee) ; Brančík, Lubomír (advisor)
This bachelor‘s thesis deals with the task of designing an audio amplifier, operating in class D, with a nominal output power of 2 x 80 W with Bluetooth connectivity, supplemented by an equalizer and a state display. A power supply and a user interface are designed as well. At first, research regarding audio amplifiers is made, followed by a more thorough description of class D operating principles. Afterwards the actual synthesis of the desired amplifier is presented, followed by the power supply design procedure. The correctness of the synthesis is later verified by simulations in PSpice and LTSpice. Theoretical design is then practically built, and its parameters are confronted with expected values by measurements.
|
|
|
A Laboratory Task: Oscilloscope Measurement
Malý, Ondřej ; Steinbauer, Miloslav (referee) ; Marcoň, Petr (advisor)
Bachelor thesis deals with the design of a signal generator for a laboratory task of the subject HELE. As a generating chip is used ICL 8038 that can generate three types of waveform – sinus, square wave and triangle. The frequency range is from 20 Hz to 20 kHz in selected circuit. Output is connected to oscilloscope probe, but also to 3.5mm headphone jack through which can be the selected waveform listened to on the connected headphones or speakers and measure the audible threshold.
|
|
|
Design of an audio amplifier is class D
Holínský, Jan ; Šotner, Roman (referee) ; Kledrowetz, Vilém (advisor)
The thesis deals with principles of individual types of low frequency amplifiers. There are described principles of amplifiers in different classes with respect to their distortion and efficiency. Type D amplifier is described in detail block by block. There are also designed blocks of audio amplifier in the class D. The selection of components according to the necessary parameters is considered. The audio amplifier is designed so that its output power is closer to 100 watts per channel.
|
|
|
Power supply and protection circuits for 6-channel audio amplifier
Kryška, Vojtěch ; Balík, Miroslav (referee) ; Hanák, Pavel (advisor)
This bachelor thesis deals with designing protection circuits for 6 channel audio amplifier. Created circuits provide AC voltage filtering, current peak limitation after switching on, delayed speakers connection for eliminating crackling, automatic shut down in case of overheath, LED indication of failure and waking up from standby mode. Created design focuses on keeping all channels grounds unconnected with each other for eliminating ground loops.
|
|
|
Audio amplifier for detecting wood-destroying pests
Jaroš, Ondřej ; Křepelka, Pavel (referee) ; Friedl, Martin (advisor)
This bachelor´s thesis is focused on design of detector of wood-destroying pests, which is solved by using an acoustic sound source with piezo electric element as a sensor. The acquired signal is step by step amplified to a level when we can observe the audio spectrum using a headphone. The realized audio amplifier is complemented supplemented by an active analog filter for the ability to listen to a narrower frequency spectrum. The next feature of the detector is that it displays the frequency spectrum on an LCD display ranging from 0 Hz to 10 kHz. The spectrum of the signal is acquired by using DFT transformation. Analysis of the device is firstly described from the theoretical part through the realized design. At the end of document the results are summarized.
|
|
|
Design and realization of an active subwoofer
Hrdina, Robin ; Kledrowetz, Vilém (referee) ; Šteffan, Pavel (advisor)
This bachelor thesis describes the design and construction of a one-channel amplifier 200 W into 8 load for an active subwoofer. The design consists of an active correction preamplifier and output stage. Preamplifier is created of integrated operational amplifiers and is controlled by two potentiometers, input switch and phase switch. Output stage is created of integrated circuits LM3886T by Texas Instruments. Both stages were constructed on PCBs and were measured their parameters.
|
|
|
Design of switching stereo audio power amplifier
Christen, Jiří ; Kratochvíl, Tomáš (referee) ; Brančík, Lubomír (advisor)
This work deals with complete design of switch - mode audio power amplifier. The first part of the work describes basic principles of power amplifier operating in switch mode and differences between classes. Specific parts of the amplifier are analysed according to function and construction. The second part includes particular design and construction of the class D switching amplifier with a minimal output power 2x80W. The power stage is realized by an integrated circuit TAS5630 from Texas Instruments. Basic states of the power stage are signalized by LED diodes. The design includes correction preamplifier for adjusting volume and frequency response. The appliance is supplied from switch - mode power supply. Basic parametres were measured for individual parts.
|
|
|
Design and realization stereophonic amplifier class D
Hradil, Jaroslav ; Háze, Jiří (referee) ; Pavlík, Michal (advisor)
The aim of this project is to design a class D stereo audio amplifier with output power of 2 x 50 W into 4 load with THD+N less than 10%. Project is divided into three parts. First part describes the principles of class D amplifiers, the second part contains actual design of amplifier and the last part presents the results of the measurements.
|
|
|
Class D 2.1 audio amplifier for laboratory measurements
Děcká, Klára ; Polák, Ladislav (referee) ; Kratochvíl, Tomáš (advisor)
This semestral thesis deals with a draft and construction of the design of an class D audio amplifier with pulse width modulation. The resulting design consists of a supply protection, an active crossover and the output power stage itself. The amplifier is made in 2.1 configuration, the amplifier for mid/high audio frequency drives 2 × 30 W output into a 8 load, subwoofer drives 1 × 100 W into a 2 load. The control centre of the whole application is an integrated circuit TPA3116D2 by Texas Instruments company. The resulting audio amplifier will be used as a device for laboratory measurements.
|
|
|
Class D stereo audio power amplifier
Kazelle, Kamil ; Dostál, Tomáš (referee) ; Brančík, Lubomír (advisor)
The content of this project is design of stereo audio amlifier working in class D with output power 2x20W. Project includes also a design of preamplifier and power supply. This project is divided into the four parts. In first part the theory and problems of amplifiers working in class D is resumed, in the second the designed circuits are dicussed, in the third the results of simulations in the program PSpice are presented and the last part of project describes the realization and presents the results of measurements.
|
guest ::
