|
|
Monitoring of GSM network
Trávníček, Tomáš ; Krajsa, Ondřej (referee) ; Koutný, Martin (advisor)
This master’s thesis is focused on problems of monitoring GSM network using a mobile phone. Problems are analyzed on a theoretic basis with a description of available network parameters. Then the thesis offers a description of existing application environments providing a user with given data about the network. The main part of this work describes a development of application compiling queue data from mobile network and GPS, and creates output data illustrating signal strength in selected areas. The work also includes extensive measuring in select areas together with an evaluation of the processed data.
|
|
|
Analysis of UMTS signalling
Trojáček, Jaroslav ; Herman, Ivo (referee) ; Havelka, Dušan (advisor)
Master thesis is focused on signalling analysis of third-generation mobile network UMTS. In first part of master thesis is described a question of standard IMT-2000, introduces the principles of the WCDMA air interface, gives a wide overview of the UMTS system architecture and signal processing. In second part of master thesis is described a question of signalling analysis, including general protocol model for UTRAN terrestrial interfaces. This chapter is focused on elementary procedures, Radio Resource Management procedure examples, Mobility Management procedure examples and Call Control procedure examples in the first place. Last chapter of master thesis is focused on radio network planning of UMTS with practical location of basic station Node-B.
|
|
| |
|
|
Rotation Electric Actuator: parameter estimation and control
Palaj, Lukas ; Houfek, Lubomír (referee) ; Grepl, Robert (advisor)
The bachelor’s thesis deals with design of printed circuit board in the first part. The board will be used for connecting rotation electric actuator (REA) to the card MF624. It is written about electronic throttle and it’s particular parts, it’s connection to the card and estimation of parameters necessary for composing a virtual model in Simulink in the second part. After that control for the model is designed.
|
|
|
Speed Increasing for Track Section Moravské Budějovice - Šumná
Vlachová, Dominika ; Komárek, Jan (referee) ; Svoboda, Richard (advisor)
This work deals with the possibility of increasing the speed of the track section of the Moravské Budějovice – Šumná. Speed increase is considered with the current geometric parameters of gauge, and then with the proposed changes to the geometric parameters of the track. The proposed changes, however, must not cause significant interference to the body lines. Furthermore, it is also taken into account speed limits in areas of railway level crossings, rolling fork, positions of signals, etc.
|
|
|
Speed Increasing for Track Section Křenovice - Nezamyslice
Bombera, Jan ; Kroupa, Jan (referee) ; Svoboda, Richard (advisor)
Bachelor´s thesis deals with the possibility of increasing the line speed at Křenovice – Nezamyslice track number 315A. Speed increasing is tested in two steps – with current track geometry parameters and with changing some of the track geometry parameters, but always in order to meet regulatory and normative limit values. The new speed is determined for conventional vehicles and for vehicles that are able to take advantage of cant deficiency I > 100 mm. Speed limits in locations of railway crossings, signals position, etc., are taken into account for speed increasing. In some cases are proposed measures to change these objects.
|
|
|
Transient Effect at the Output of a Linear Dynamic System Controlled Pulse-Width Modulation
Petera, M.
The goal of this work is to determine the size of overshoot produced at the output of a linear continuous second order system controlled by pulse width modulation. This work contains the calculation of the output signal response of the system in the time domain using the Laplace transform. The calculations of the amplitude of the output signal based on the pulse width modulation and system parameters are performed in this work. Finally the possibilities were given to determine the suitable period of pulse width modulation for required ripple. All the important calculations were compared with the simulations in the MATLAB-SIMULINK program and with the measurement at the real inertia second order cell.
|
|
| |
|
|
Measurement cables and connectors for audio
HAVEL, František
This thesis deals with design and practical implementation of a comprehensive test for measuring and comparing the performance of audio cables and connectors used in audio technology. The theoretical work is the part that deals with the signal, sound, cables and connectors and methods of measurement used. In the practical part are results and comparison of wide price range instrumental cable. Studied parameters are: the electrical resistance of the cable, the capacity and inductance. Was also been studied the affect of the cable using frequency analysis. It was created overview table, which summarizes the findings.
|
|
|
Microwave interconnection, realization, used technologies and operation
OLIVA, Radim
This work deals with generally questions of microwave connections. In work we found information about wire-less transfers dividend in line with frequence ray inclusive abstrakt of technology. Also there are general information about wireless transfer, used modulations and data security during the transfer. In praktical part we located concrete project of concept data trace, on which I worked and took part on realization.
|
guest ::
