|
|
Hole punching problematics of two layered sheet metal
Kvapil, Štěpán ; Peterková, Eva (referee) ; Císařová, Michaela (advisor)
The thesis is focussed on project of a tool – a hot working clipping punch, where the hole is punched in the upsetting ends of stabilizer. We talk about punching of a two layered semi-finished product, in which burr is formed at the layer interface, which is undesirable from the point of the customer requirement. The stabilizer is mounted in the car chassis, where it is fastened to the axle with screws. The literature study is focused on the theory and problems of punching. In the practical part, several design solutions of cutter faces are discussed, from which three types of face shape were selected. This was associated with a change in the design of the ejector. Two tool materials were selected for comparison. The cutters were tested on an automatic forming centre. Finally, after summarizing and evaluating all the practical experiments, an optimal solution of a tool designed for punching a hole with a two layered semi-finished product is proposed.
|
|
|
Tail units design of VUT 100 aircraft made out composite
Berka, Martin ; Cejpek, Jakub (referee) ; Mališ, Michal (advisor)
This Master´s thesis describes the design of composite horizontal tail of VUT 100 aircraft. Load calculation and selection of the critical load cases is performed. Internal structure of stabilizer and right elevator is designed. Construction materials are chosen and the structure of the composite materials is proposed. FEM models of stabilizer and the right elevator are created in MSC Patran system and consequently the strength test of the models for the selected load cases is executed using MSC Nastran software and COMPOST.
|
|
| |
|
|
Study of Belite Structure and Stability
Adameková, Paulína ; Kalivoda,, Karel (referee) ; Gazdič, Dominik (advisor)
This diploma thesis deals with the preparation of clinker mineral belite. The aim is to optimize the preparation of belite followed by monitoring the influence of side oxides, the preparation process and also the firing on the stability of ß - C2S. The work focuses primarily on the preparation of ß - C2S without stabilization, based on previous research in the field of clinker minerals at the ÚTHD, where the results showed a recovery method for preparation of raw material mixture and optimization of suggested firing modes.
|
|
|
Use of the Pressure Biofeedback Unit to assess m. transversus abdominis activity - a pilot study
Blektová, Veronika ; Vomáčková, Helena (advisor) ; Stupková, Michaela (referee)
Title: Use of the Pressure Biofeedback Unit to assess m. transversus abdominis activity - a pilot study Aims: The aim of this Master's thesis is to create an extended rating scale to assess the stabilizing ability of the transverse abdominis muscle measured by the Pressure Biofeedback Unit through PRONE test. Another aim of this thesis is to determine whether the extention of the original rating scale designed to evaluate the stabilizing ability of the transverse abdominis muscle measured by the Pressure Biofeedback Unit in the PRONE test will increase sensitivity of this evaluation. Methods: This thesis is a quantitative study, i tis a quasi-experimantal study. A deliberately selected group of young active men n = 40 with a mean age of 25,63 2,61 who suffer from chronic low back pain without a neurological finding for at least 3 months was used for this study. The size of the research sample was determined using statistical power calculation software G*Power. A questionnaire for experts in the field of physiotherapy was used to create a proposal for the extended rating scale. The Fleiss' K and the arithmetic mean were calculated to evaluate the inter-rater agreement and content validity of the individual items in the questionnaire. The measurement itself took place in the premises of Posádkové...
|
|
|
Battery supplied lawn mower
Picmaus, Jan ; Martiš, Jan (referee) ; Vorel, Pavel (advisor)
The thesis deals with a concept of turning a conventional petrol powered lawn mower to a battery powered solution which is powered by lithium cells. A division to three chapters, comparison, mechanical and electrical, provides fluency of the whole design and further realization. The arrangement of chapters is performed so that the continuity of the thesis is maintained. Calculations of parameters of every motor and transmission with choosing particular devices are just a part of much interesting information which can be found in this thesis. All new components have full documentation except those which were changed during manufacturing. The electrical part explains every part of the schematics in detail. The realization contains difference between preliminary design and further production, manufacturing of the PCB and powering up the motor drives. The last part of the thesis contains temperature measurements of the device at no load.
|
|
|
Design of JA-400 adjustable horizontal tail
Mach, Tomáš ; Vaněk, František (referee) ; Jebáček, Ivo (advisor)
Tato diplomová práce se zabývá návrhem stavitelného stabilizátoru za účelem vyvažování letounu a zlepšení jeho letových výkonů. Cílem práce bylo navrhnout konstrukční řešení ovládání a zavěšení horizontálního stabilizátoru. Součástí je pevnostní výpočet kritických konstrukčních prvků a návrh letových zkoušek. V závěru jsou zhodnoceny výhody a nevýhody nového řešení a posouzení možnosti sériové výroby. Klíčová slova Ultralight, JA – 400, stabilizátor, stavitelný stabilizátor, vodorovné ocasní plochy, vyvážení. Abstract This thesis describes the design of adjustable stabilizer for the purpose of balancing the aircraft and improve its flight performance. The aim was to propose a design solution for control and hinge system of horizontal stabilizer. It includes the strength calculation of critical structural components and the design of flight tests. The conclusion evaluates the pros and cons of the new solutions and possibilities of mass production.
|
|
|
Hole punching problematics of two layered sheet metal
Kvapil, Štěpán ; Peterková, Eva (referee) ; Císařová, Michaela (advisor)
The thesis is focussed on project of a tool – a hot working clipping punch, where the hole is punched in the upsetting ends of stabilizer. We talk about punching of a two layered semi-finished product, in which burr is formed at the layer interface, which is undesirable from the point of the customer requirement. The stabilizer is mounted in the car chassis, where it is fastened to the axle with screws. The literature study is focused on the theory and problems of punching. In the practical part, several design solutions of cutter faces are discussed, from which three types of face shape were selected. This was associated with a change in the design of the ejector. Two tool materials were selected for comparison. The cutters were tested on an automatic forming centre. Finally, after summarizing and evaluating all the practical experiments, an optimal solution of a tool designed for punching a hole with a two layered semi-finished product is proposed.
|
|
|
Measurement of meteorological variables
Škorpík, Daniel ; Harabiš, Vratislav (referee) ; Chmelař, Milan (advisor)
This bachelor thesis discusses about the basic meteorological variables, especially temperature and airflow. These magnitudes are measured using an anemometer which uses resistive sensors, namely, two thermistors of NTC type that described technology, operations, methods of scanning, sensor placement and implementation of such a device. After that was designed block diagram and circuit diagram. The meter is realized, than we describe the individual components and then is calibrated and tested. In conclusion, it is evaluated for use in medicine.
|
|
|
Design of analog control device for mini glasshouse
Řehák, Martin ; Lukeš, Zbyněk (referee) ; Petržela, Jiří (advisor)
Nowadays there are several options how to grow plants that do not come from our climatic belts are used to implement the greenhouses, where the artificially simulated environments, in which plants can vegetate. This work deals with the issue, plant growing in climates that are not for the plants of the rainforest, characteristic. It was necessary to create a greenhouse in which to guarantee the basic conditions for their growth. Such as humidity, temperature and lighting. He was taken into account at the design and implementation of the website.
|
guest ::
