|
| |
|
|
Slurry surfacing - composition and quality issue
Dostál, Filip ; Koudelka, Tomáš (referee) ; Hýzl, Petr (advisor)
This thesis is focused on slurry surfacing technology, particularly on microsurfacing. The theoretical part describes the differences between the slurry seal and microsurfacing. Ingredients for the production and laying. There are also described their advantages. The practical part presents proposal of mixture and demonstrate that the service of life of the emulsion mixture is closely related to the content of residual binder and composition of microsurface.
|
|
|
Stabilization of bank
Podola, Martin ; Pelikán, Petr (referee) ; Šlezingr, Miloslav (advisor)
The subject of this bachelor’s thesis is assessment of reservoir banks Bystřička in terms of abrasion. Judgement is focused on two main points on the northeastern bank of the reservoir near the tributary. It is an area near the hotel Beskydská Tatranka. Thesis is finished with design of selected biotechnical measures to slow or stop erosions banks.
|
|
|
Study on wear of material in contact with MR fluid
Žáček, Jiří ; Vimmr, Jan (referee) ; Kubík, Michal (advisor)
This paper is focused on MR dampers and its critical parts in term of damper`s durability, which seems to be a piston-rod seals, and it should find an ideal material combination of seal and MR fluid for increasing the damper`s life. The tests were conducted in modified pin-on-flat configuration, which was supposed to be more suitable for laboratory testing. There was tested and compared a suitable material for seals, like PTFE, NBR, SBR of polyurethanes. The article is also focused on MR fluids and its contribution to seal`s wear. The impact of particle concentration, wear of MR fluid and effect of modification of MR fluid was tested. It showed up, that the best material for seal is H-PU95FDA. The effect of particle concentration is negligible on seal`s wear, while effect of modification and wear of MR fluids are significantly higher.
|
|
|
Proposal to revitalize the banks of the flooded Hulín sand pit
Skřížala, Lukáš ; Pelikán,, Petr (referee) ; Šlezingr, Miloslav (advisor)
The master´s thesis deals with the assessment of the state of the shore territory on the Brno reservoir, in the Osada area and subsequently the proposal for shore stabilization. As part of a personal visit to the area of interest, photographic documentation, geodetic focus and subsequent assessment of the current state of the abraded shores were made. Using the geodetic focus and data of water heights on the reservoir provided by the Povodí Moravy, s.p. the most numerous in the reservoir was evaluated in 2007-2017, the coastline retreat and the proposed shore stabilization were determined. There was suggested totaly eight measures were proposed against the further retreat of the shore line, which were incorporated into schemes and visualizations.
|
|
|
Coating properties of cutting tools carbide
Doležalová, Petra ; Bumbálek, Bohumil (referee) ; Osička, Karel (advisor)
Diploma thesis is divided into two parts. The first part is focused on theoretical description of coating methods, on currently used coatings, their properties and it is also focused on description of methods, which are used for analyzing each property. The second part focuses on testing of coatings and analyzing of the values obtained from experiments. The aim of this thesis is then to compare the properties of the tested coatings.
|
|
|
Bank stabilizotion of Letovice dam
Mika, Jiří ; Pelikán, Petr (referee) ; Pelikán,, Petr (referee) ; Šlezingr, Miloslav (advisor)
The master's thesis is focused on the statistical evaluation of the most frequent level in the tank for 10 years, determining the abrasion terminant, setting retreat shoreline and bank stabilization proposals in the area of interest Svitavice on the water reservoir Letovice. The thesis consists of an accompanying report and a technical report. The accompanying report contains basic technical and administrative data, hydrology ratio and others conditions in the area of interest. In addition, the accompanying report contains a description of production and activities in wide surroundings of the tank. The technical report contains statistical evaluation of the most frequent water surface in the tank for 10 years, hydro technical calculation to determine the prognosis of the bank line recession, visualization proposal of biotechnical measures. In conclusion, an estimate cost of the proposed biotechnical measures is calculated.
|
|
|
Measurement of wear in shock absorber with magnetorheological fluid
Žáček, Jiří ; Strecker, Zbyněk (referee) ; Roupec, Jakub (advisor)
This bachelor thesis deals with measurement of abrasivity of magnetorheological fluids and its effect on hydraulic shock absorber. The abrasion could be measured and evaluated by many ways. The pin on block measurement method has been selected for this test. The pin was moving on a steel block while the whole system was surrounded by magnetorheological fluid. According to results, the lifetime of magnetorheological shock absorber is 4 times shorter than classical damper. Results of this thesis could be helpful in damper construction or in development of new magnetorheological fluids.
|
|
|
Establishment of bank slope retreat forecast
Čuda, Ondřej ; Pelikán,, Petr (referee) ; Šlezingr, Miloslav (advisor)
The diploma thesis deals with the assessment of the condition of the bank area of the flooded gravel sand pit Hulín, the subsequent design of active anti-abrasion structures and the determination of the point of maximum retreat of the bank line. As part of the assessment, a personal field trip was carried out, during which, in agreement with the supervisor, a shore section was designated for the subsequent proposal of a stabilization measure and its photo documentation. From the data provided by the supervisor, the characteristics of the waves, the starting length of the wind, the level of the heel of the highest abrasive log house were calculated and the point of maximum retreat of the shoreline in the focused transverse profile of the solved section was determined graphically. Part of the diploma thesis is the design of a total of six active anti-abrasive structures, the construction of which will prevent further retreat of the shoreline and support the creation of a habitat for local animals.
|
|
|
Mortar with alkali-activated matrix
Černá, Hana ; Hela, Rudolf (referee) ; Bodnárová, Lenka (advisor)
The thesis addresses the issue of alkali-activated materials and their manufacturing components. In the theoretical part the description of such materials is provided and the requirements for source materials are defined. The theoretical part further addresses the resistance of alkali-activated materials and their lifespan - namely sulphate resistance, chloride resistance, acid resistance, frost resistance, porosity, carbonation, resistance, abrasion resistance and heat resistance. The experimental part of the thesis focuses on compounding four different mixtures of alkali-activated materials. In the loosened stage, the weight was measured. In the hardened stage the weight was measured as well as the tensile strength when bending, the strength under pressure applied, heat resistance, water and defrosting chemicals resistance and formation of cracks.
|
guest ::
