| |
|
Spectral method for motor parameters identification
Sedláček, Filip ; Buchta, Luděk (referee) ; Pohl, Lukáš (advisor)
This project deals with the problem of spectral method for system identification. Introductory part acquaints reader with basic concept of identification and explains its application in practice. It describes and mathematically derives two non-parametric methods for identification – correlation method and spectral analysis. The main aim of this final project is testing and implementation of spectral analysis in system parameters identification, which is specifically described in remaining sections of this project. These sections discuss a fundamental rules, procedures and principles in order to prepare a reader as much as possible for its final application in REAL-TIME system identification.
|
| |
|
Methods of Technical Diagnostics
Klusáček, Stanislav ; Ďaďo, Stanislav (referee) ; Němec, Zdeněk (referee) ; Tůma, Jiří (referee) ; Bejček, Ludvík (advisor)
The main objective of the presented thesis is to contribute to the development of diagnostic methods for piezoelectric sensor testing. The thesis describes the methods for piezoelectric sensors microcracks identification and diagnostics. The core of the thesis presents the development of a knock sensor prototype, design of suitable methods for the knock sensors diagnosis and evaluation of developed methods with focus on detection of microcracks in the sensor piezoceramic. The last part of the thesis deals with the influence of cracks and splits on the measured data from the piezoelectric transducer. The presented methods are focusing on impedance measurements and sensors frequency response measurements. Known properties of used piezoelectric material as an information source for measurement and diagnosis are provided. The main result of the work is the evaluation of the methods developed for the piezoelectric sensors self-diagnosis.
|
| |
|
Dynamics of heating surfaces and radiators including control valves
Bartusek, Jiří ; Charvát, Pavel (referee) ; Štětina, Josef (advisor)
This thesis is theoretically described heating surfaces, radiators and regulation valves. There are also described their features, advantages and disadvantages and division according to design. The aim of the work is determine the dynamics characteristics of heating surfaces and radiators including control valves, which are parts of measurement panel. Based on the measurement are determined appropriate characteristics of which are calculated values for regulating. The result of this study can serve as a guide to the practical measurement method of dynamics characteristics of the real-working heating systems, or serve as a template for the settings according to the measured data.
|
|
Experimental workplace of controlled drive with high dynamics
Rozkošný, Miroslav ; Marada, Tomáš (referee) ; Němec, Zdeněk (advisor)
My diploma thesis deals with the basic principle of the frequency inverter and his construnction. In the next section are analyze the basic properties and characteristics of the using equipment. The main part of this thesis is to investigate the dynamic properties of asynchronous electric motor controlled by a frequency inverter using STARTER. The results of experiments are compared and analyzed.
|
|
Design of 10-channel audio equalizer with optimization of frequency characteristic and spectral audio analyzer
Štěrba, Václav ; Dvořák, Radek (referee) ; Šotner, Roman (advisor)
This work deals with the design of a 10-zones equalizer with optimized frequency characteristics with a spectrum audio analyzer. In this work the problem of processing audio signals using equalization for filtering the interference frequencies, correction of frequency cover signal boost or suppression of the required zones of the audible spectrum are also analyzed. The influence of subjective perception of sound intensity of the audio signals reproduction and its use in working with equalizer is discussed too. The work describes the principles and usage of the audio-analyzer as a tool for the optimization of the audio equalization setting when ensuring the appropriate listening conditions of music reproduction, spoken word, sounds, etc. It also focuses on the signal source for testing audio-chains, their generation and measurement using the audio analyzer. The equalizer equipment, audio-analyzer generator of reference signals equipment and power supply are designed as a single unit.
|
|
VFA and CFA comparison
Vystrčil, Marek ; Hubálek, Jaromír (referee) ; Stehlík, Jiří (advisor)
This bachelor's thesis is focused on comparison of operational amplifiers structures with voltage (VFA) and current (CFA) feedback. In the theoretical part there is an analysis properties of operational amplifiers. Attention is paid to advantages of particular amplifiers in concrete networks. The practical part contains the simulations of those networks with an aim to assess characteristic properties and a difference between applied circuits. I used the operational amplifier µA741 for the simulation of the structure VFA. I used the amplifier AD8011 for the simulation with current feedback. I added the theoretical and practical differences between comparative structures.
|
|
Position control of cross-table dedicated manufacturing machine
Plocek, Jaroslav ; Vetiška, Jan (referee) ; Houška, Pavel (advisor)
The bachelor thesis treats the drive solution of the two axis cross-table of a single-purpose manufacturing machine. The first chapter analyzes the concept of drives and compares different variants using either a direct linear drive or a ball screw with a rotary servo drive. The thesis further deals with sizing the motor and the power unit assembly and the description of the whole measuring system. The structure of cascading position controller, its description and the calculation of current and speed control loops is covered in the next part. The last section discusses practical settings of all control parameters.
|