|
|
The influence of decreasing of impeller diameter, change Q - Y characteristic
Hyriak, Maroš ; Habán, Vladimír (referee) ; Haluza, Miloslav (advisor)
The purpose of the thesis is to familiarize with the fundamental characteristics of ta centrifugal pump while changing geometry of the output section of its impeller trimming. Characteristics of a pump is calculated whilst diameter of the impeller is changed. More specifically, changes in the flow and energy are observed while diameter of the impeller is decreasing. Two possible solutions, approximate and accurate, are offered for both parameters. The thesis suggests that an application of the approximate solution is satisfactory for the flow calculation of the impeller. In contrast, for the energy calculation is the approximate solution sufficient only in case of the slight trimming. Increase in the trimming results in the drop of the hydraulic efficiency and decrease in the accuracy of the results. Consequently, the accurate solution is recommended for the energy calculations. Limitations of the paper may be represented by two facts. First, in comparison with the calculations, results are in reality affected my numerous variables that have not been included in the calculations due to their unpredictability. Second, calculations were based on the several assumptions that are rarely met in the reality. The results of the thesis are applicable in the every-day life when adapting the pump to the customer needs.
|
|
|
Spiral case design for fountain turbine Katovice.
Čípa, Jiří ; Veselý, Jindřich (referee) ; Haluza, Miloslav (advisor)
The diploma thesis should identify inconsistencies of the small hydraulic power plant Katovice. The fountain water turbine is now running in slower delivery because the original Francis high speed turbine achieved much smaller flow than a Kaplan type turbine. The aim of the thesis is a project of a spiral case and a distributor for the Kaplan turbine, which should work in higher flow and should be run in its optimum. This project will serve as a base for construction of distributor and spiral case for the small hydraulic power plant Katovice.
|
|
|
Emptying of the rotating vessel
Hideghéty, Attila ; Koutný, Luděk (referee) ; Haluza, Miloslav (advisor)
This bachelor´s thesis handles with happenings related to hydromechanics. For all stands Euler´s equations of hydrostatics, hydrodynamics and Bernoulli´s equation. The water has got a characteristic surface in the rotating vessel, by increasing the revolutions the water begins to pour out. The task is analyzing the events that can occur when the vessel is rotating with the water.
|
|
|
The influence of the impeller diameter decreasing on the pumps characteristic
Jelen, Richard ; Haluza, Miloslav (referee) ; Habán, Vladimír (advisor)
This master’s thesis deals with changing the geometry of the output section of the impeller of the radial centrifugal pumps and its influence on the characteristics of the pump. In engineering practice for these radial centrifugal pumps it is possible to change the parameters based on the requirements. This adaptation of parameters is called impeller trimming. Impeller trimming means the reduction of the impeller diameter thereby decreasing the flow, head and efficiency. Existing equations for calculating the changes in the characteristics of the impeller trimming are inaccurate. In this thesis is describes a possible method of putting for the recalculation characteristics of a pump based on the impeller diameter on the available characteristics of pumps.
|
|
| |
|
|
The wide range impeller.
Wojnar, Pavel ; Žák, Radim (referee) ; Haluza, Miloslav (advisor)
The aim of the thesis was to propose a pump impeller with higher effectiveness and verify the proposal with the calculation using programs Gambit and Fluent. Three designed impellers were afterwards made using 3D printer and its characteristics were measured in a hydraulic laboratory in Kaplan Department of hydraulic machines. The proposal of a so called wideband impeller of the centrifugal pump was made with chaotic ordering of blade cascades, in one impeller occur blades with various input and output angles and different shapes of blades but all blades have got similar shape in a meridian sectional view of impeller. The thesis was divided into three parts. In the first part, a conforming transformation was theoretically described which was in the thesis used for the shape proposal of impeller blades. In the second part of the thesis final proposals and calculations of pump impellers were made. The third part of the thesis focused on the processing and evaluation of experimental measurement in the hydraulic laboratory and finally the results of the thesis were summarized in the conclusion.
|
|
|
Modeling of surface waves
Zgabaj, Martin ; Haluza, Miloslav (referee) ; Franců, Jan (advisor)
This bachelor's thesis presents the derivation of basic characteristics of surface waves which includes the dispersion relation, the shape of the wave, the phase velocity, the group velocity and the movement of water particle. Thesis deals with both deep-water waves and shallow-water waves. Derived characteristics are examined in both cases. In the last part of thesis there are specific examples of those two types of waves.
|
|
| |
|
|
Feasibility study of small hydro power plant on the river Papradnianka in the district of Povážská Bystrica
Barenčík, Ladislav ; Haluza,, Miloslav (referee) ; Šulc, Jan (advisor)
The main purpose of this bachelor's thesis is the design of conceptual solution of a small hydroelectric power plant on the river Papradnianka in the Prúdy area and a feasibility assessment of this project. Hydrological data and a selection of the most appropriate type of power plant are revaluated in the first part of this bachelor's thesis. A selection of appropriate technology and individual parts of small hydroelectric power plant are described in the following part. Economic return of this project is assessed in the last part. According to the results of this bachelor's thesis, this project is technically realizable, but the return of investment is big due to current prices of energy .
|
|
|
Improving of hydraulic properties of swirl turbines
Kůrečka, Jan ; Veselý, Jindřich (referee) ; Haluza, Miloslav (advisor)
This diploma thesis describes design of blade geometry of swirl turbines with different blade row density for given parameters Q11 = 1,9 [m3s-1], n11 = 170 [min-1], H=2,5 m, and =0,8. Goal is to found out differences between designs with high count of runner blades and design with fewer blades. Comparison of computed characteristics of three, seven and nine bladed runners is given.
|
guest ::
RSS feed.