|
|
Gelation of waterglasses depending on their composition
Otřísalová, Pavlína ; Kalina, Lukáš (referee) ; Bílek, Vlastimil (advisor)
This bachelor thesis studies how are gelation of sodium and potassium silicates (water glass) influenced by their composition. The main goal of the thesis was to investigate the effect of silicate concentration, molar ratio, and alkaline ions on the gelation time. Qualitative analysis of obtained gels was also performed. The thesis includes literature research in the field of chemistry of silicate sols and gels. In the experimental part were prepared samples of both sodium and potassium silicates with silicate concentrations of 15 M and molar ratios of 0,53,0. Gelation was induced by adding calcium ions. Gelation time was measured using rheological oscillation tests (time sweep) and visual method. Qualitative analysis of the gels was performed using rheological oscillation tests (amplitude and frequency sweep) and visual method. Three significant trends were observed: 1) NaVS samples always had shorter gelation time than KVS samples 2) the higher the silicate concentration the higher the gelation time 3) gelation time of samples with molar ration of 2 was most influenced by silicate concentration. It was also observed that the formation of gel network was promoted in systems with 1) higher molar ratios 2) higher silicate concentrations 3) presence of K+ ions. Gels with molar ratios 2 were significantly weaker than those with ratio of 2,5 or 3,0.
|
|
|
Composite materials based on alcali activated blast furnace slag with admixture of fly ash
Indra, Ivo ; Brandštetr, Jiří (referee) ; Opravil, Tomáš (advisor)
This thesis concerns on substitution of blast furnace slag or its part with fly ash in alkali-activated systems based on aluminosilikates. Classic, fluid bottom and fluid filter fly ashes will be tested. The goal is to prepare geopolymer with required mechanical properties, but with maximal admixture of alternative raw materials. In composites with substitutioned slag or its part the thesis focuses mainly on workabilityof fresh mixture, pressure and bending strenght. Use of secondary raw materials has advantages in the economic point of view and it´s friendly to enviroment, too.
|
|
|
Possibilities of alcali activation of steel slag
Frýbortová, Iva ; Rovnaník, Pavel (referee) ; Opravil, Tomáš (advisor)
The properties of alkali activated steel slag as a clinker-free binder system was studied in this thesis. The aim was to find the optimal composition of alkaline activator providing good properties of the prepared binder. Sodium and potassium hydroxides and alkaline silicates in the form of solutions and powders were used as the activators. Mixture of steel slag, fluidized bed coal combustion ash and water without any activating ingredient was another binder system studied in this work. Mechanical properties, such as compressive and flexural strength, of the mixtures were determined. Calorimetric measurements were used for the study of hydration process, scanning electron microscopy for the examination of microstructure.
|
|
|
Thermoproperties of foundry moulds in dependence on different used foundry sands
Šuráň, Jiří ; Rusín, Karel (referee) ; Cupák, Petr (advisor)
The project elaborated in frame of engineering studies is submitting the study of thermal properties of holding mixtures using different types of sand. Were tested a total of 5 sands: zirkon, ŠH22, chromite, olivine and dunite. Molding compounds were tested for thermal capacity, thermal conductivity and heat accumulation. The highest heat capacity was achieved in dunite sand. The largest heat accumulation had mixture with chromite sand and the best thermal conductivity was found in a mixture with olivine sand.
|
|
| |
|
|
Methodology for determining the chemical composition of water glasses
Flídrová, Michaela ; Bartoníčková, Eva (referee) ; Kalina, Lukáš (advisor)
The bachelor thesis deals with the methodology of determination of the chemical composition of water glasses. The aim was to find a more suitable method than the colorimetric analysis used by one of the domestic water glass manufacturers. The current procedure can be used to determine the content of Me2O (Na2O, K2O, Li2O), however, in the determination of SiO2 the method is inaccurate since the color change of the indicator during the second titration is very slow and therefore the equivalence point is ambiguous. The main aim of this work was to find a suitable method for the complex determination of the chemical composition of water glasses, which is compared with other methods used in the analytical chemistry of silicate materials. A very promising method is the conductometric titration with a volumetric hydrochloric acid solution, which provides an accurate, fast and instrumentally inexpensive method of chemical determination.
|
|
|
The development of composites based on alkali-activated matrices resistant to extreme temperatures
Ševčík, Marek ; Šácha, Libor (referee) ; Dufka, Amos (advisor)
The diploma thesis is focused on the development of composites from alkali activated materials (AAM) and their resistance to extreme temperatures. The theoretical part describes alkaline activation and precursors for the production of AAM. Furthermore, the problem of the effect of extreme temperatures on these materials is described. In the experimental part, the optimal silicate modulus with respect to the properties of AAM was gradually determined, and the effect of extreme temperatures on the AAM matrix was verified. In the next stage, the effect of the filler with respect to the behavior at extreme temperatures was tested and then the final formulation was optimized.
|
|
|
The possibilities of using of foundry filter ash
Solik, Jaroslav ; Šoukal, František (referee) ; Opravil, Tomáš (advisor)
This thesis explores the posibility of using of foundry filter ash for production of inorganic composite materials, that could be used primary in the construction industry. The thesis is divided into theoretical and experimental section, where theoretical section contain literature review of used materials and the experimental section summarizes the results of laboratory tests performed on tested mixture based on portland and alumina cement with various content of foundry filter ash. For comparison was also used another foundry waste - foundry sand. Prepared test bodies with dimension of 40 x 40x 160 mm was subjected to mechanical strength tests and the influence of amount of foundry waste on the strenght of the prepared mixtures was monitored. Next the thesis deals with possibilities of alkaline activation of foundry waste, where sodium water glass, sodium hydroxide and commercially supplied baucis L 160 component B were used as alkaline activator. These test mixtures were also subjected to mechanical strenght tests and the influence of amount of foundry waste on the strenght was observed too. The analysis of input materials were performed by XRF, TG – DTA – EGA and XRD powder diffraction methods. All strength tests were tested by testing equipment desttest 4310.
|
|
|
Water Treatment Plants Innovation Opportunities
Zelený, Zdeněk ; Biela, Renata (referee) ; Kučera, Tomáš (advisor)
This master´s thesis deals with the possibilities of innovation process water treatment. Specifically, to explore the use of sodium water glass and nanoiron in removing heavy metals from raw water at the drinking water treatment. For the comparison was used traditionally used coagulant, particularly liquid aluminum sulfate. The introductory part deals with the possibility of modifying the surface water during the treatment process such water into potable water. This chapter is a description of the quality of raw water used, then the description of currently used separation processes. Furthermore, they are described and commonly used types of treatment plants. Conclusion The introductory section deals with traditional coagulants and form a suspension. Another part of this master´s thesis has been devoted to the possibilities of innovation in the treatment of raw waters as drinking water, describes the options and features of the use of water glass and nanoiron. The following section describes the experimental part of this thesis. It is followed by the experimental results. The last chapter summarizes the acquired knowledge and commented on the measured values of the experimental part. This work also shows several specific projects using innovative technologies presented.
|
|
|
Water soluble foundry binder with heat hardening
Prokop, Tomáš ; Burianová, Klára (referee) ; Cupák, Petr (advisor)
Foundry production produces the biggest amount of dangerous waste, which has a negative impact on environment and working conditions in the foundry. The foundry engineers test new technologies of shaping mixtures with new binders to protect environment and working conditions. We can reduce the production of dangerous waste by using better technologies and less harmful materials, which are needed for modeling forms and cores. The large source of pollution are binders, hardeners and catalyzer needed for binding sand. This work is focused on new types of ecological binders, which are dissolvable in water and are formed by setting temperature. These binders are ecological variants of known inorganic and organic binders.
|
guest ::
