|
|
UHF band front-end of quadrature receiver
Tiller, Jakub ; Špaček, Jiří (referee) ; Kasal, Miroslav (advisor)
The object of this master's thessis is study and description of RF circuits, which are used for receiveing. This work is also aimed to design this circuits and their simulation in Ansoft Designer software. Focus is placed to the standard parameters of receiving technology. The description of amplifier design is presented in this work. Parameters of this amplifier are optimalized to low noise figure. Frequency multiplier designs are included in this project.
|
|
|
Radio-frequency mixer
Kolář, Jan ; Urbanec, Tomáš (referee) ; Dřínovský, Jiří (advisor)
This bachelor's thesis is aimed to describe main parameters of mixers and principle of their measurement. There are presented devices and methods by whitch mixers can be measured. There are mentioned typical values of these parameters. The realisations of mixers are also described in this bachelor's thesis. The realisation is focussed on particular parts and circuit design. The part of this thesis is aimed to construct a working mixer and to measure its parameters. Also there is mentioned a design of laboratory exercise and an automated measurement setup done in Agilent VEE.
|
|
|
Water mixer
Damajka, Štěpán ; Glos, Jan (referee) ; Veselý, Libor (advisor)
The aim of this bachelor thesis is to build device for mixing warm and cold water. Water mixer consists of a temperature sensor and flow sensor. Actuator devices are two-way diaphragm solenoid valves and three-way valve with servo-engine. Thesis focuses on identification system and design of a suitable controller.
|
|
| |
|
|
Retrodirective antenna array
Šindler, Pavel ; Morávek, Ondřej (referee) ; Pokorný, Michal (advisor)
In the first part of this thesis a basic theory of retrodirective antenna arrays and their particular parts – antennas and mixers is summarized. Further, there is a basic summary of possibilities for an usage of retrodirective antenna arrays for an information transmission. The second part deals with the concrete retrodirective antenna array design. The design starts with creation of an antenna array model for MATLAB software. Then a suitable structure for further design is chosen. Further, particular parts of retrodirctive antenna array – a patch antenna, a mixer, a low-pass filter, a bandstop filter, a signal combiner and a Wilkinson power divider are designed and analyzed in Ansoft Designer software. For the patch antenna analysis also CST Microwave Studio software is used. The following part deals with the realization of particular parts of the retrodirecive antenna array and its parameters measuring.
|
|
|
Tuner for UHF Receiver with Low Power Consuption
Kaštánek, Martin ; Vágner, Petr (referee) ; Urbanec, Tomáš (advisor)
The purpose of this work was to make a proposal for input parts of receiver for band 430 to 440 MHz. A model of chosen semiconductor triode BFP540 was created in simulation software. Possibilities how to decrease consumption of this semiconductor triode, keeping the profit, were investigated through the simulation.In compromise consumption, keeping the profit of the amplifier - an optimal operating point for this semiconductor triode UCE = 1,2 V and IC = 2 mA was found. It was tested through the testing wiring with noise microstrips conformity. Ascertained knowledge was used for construction of tuner for UHF receiver. An operating point of input amplifier of UHF receiver was owing to power supply amplifier forced for bigger effectiveness to UCE = 2,65 V and IC = 2,0 mA. Suppression of mirror frequency is provided with Helix filter of the third order, because of intermediate frequency 10,7 MHz. Mixing on intermediate frequency is made again by semiconductor triode BFP540. Selectivity of receiver is provided with intermediate frequency crystal filter 10,7 MHz with bandwidth 15 kHz. Designed input part enables reception of SSB, FM and digital types of modulation.Bandwidth intermediate frequency exit is adapted to this request To receive particular modulation , it is necessary to complete intermediate frequency signal way with appropriate intermediate frequency filter.
|
|
|
HF and IF circuits of shortwave radiostation
Šnajdr, Václav ; Vágner, Petr (referee) ; Lukeš, Zbyněk (advisor)
The study, description, design and implementation of selected blocks of multiband shortwave radio station are dealt with in the thesis. Focus is placed on the concept of multiband shortwave radio stations, with an emphasis on high frequency and intermediate frequency circuits. The first chapter is devoted to description of the transceiver block diagram which is designed as superheterodyne. The design of bandpass input filters, intermediate frequency crystal filters and output filters is described. Simulation results and the measured characteristics of the implemented functional blocks are presented. Furthermore, the amplifier circuits which maintain impedance matching of individual blocks are discussed. SSB signal generation in the transmitter part of radio station and final stage power amplification are depicted.
|
|
|
Spectrum Analyzer up to 500 MHz
Čada, David ; Vimperk), Tomáš Baráth (Rohde Schwarz (referee) ; Šebesta, Jiří (advisor)
This project deals with design and realization of the spectrum analyser using double superheterodyne topology with frequency range up to 500MHz. This work solves hardware blocks like phase lock loops, intermediate frequency filters, saw filter, crystal filter, logarithmic detector. Content of work is also design description and tuning of spectrum analyzer parts.
|
|
|
DRM signal receiver
Mik, Šimon ; Charvát, Jiří (referee) ; Šnajdr, Václav (advisor)
The master’s thesis deals with the design of DRM (Digital Radio Mondiale) receiver. The block diagram of receiver was chosen and particular blocks were theoretically analyzed. After that followed design and production of each block. The synthesizer was programmed and the receiver properties were verified. The last part of thesis deals with real receiving of DRM broadcast.
|
|
|
Water mixer
Damajka, Štěpán ; Glos, Jan (referee) ; Veselý, Libor (advisor)
The aim of this bachelor thesis is to build device for mixing warm and cold water. Water mixer consists of a temperature sensor and flow sensor. Actuator devices are two-way diaphragm solenoid valves and three-way valve with servo-engine. Thesis focuses on identification system and design of a suitable controller.
|
guest ::
