|
|
Mechanical properties of magnesium alloy AZ91E prepared by ECAP method
Darida, Jiří ; Válka, Libor (referee) ; Pantělejev, Libor (advisor)
This thesis deals with mechanical and fatigue properties of magnesium alloy AZ91 processed by EX-ECAP method. This method involves the application of extrusion followed by equal-channel angular pressing. To obtain basic mechanical characteristics, the tensile test were carried out at room and elevated temperatures. Further the fatigue tests were performed and obtained data were used to compile S-N curve. The work also includes metallographics analysis of microstructure and fractographic analysis of fracture surfaces of tensile and fatigue test specimens.
|
|
|
Structure and mechanical properties of magnesium materials processed by HPT
Poloprudský, Jakub ; Němec, Karel (referee) ; Doležal, Pavel (advisor)
This thesis is focused on processing of pure magnesium by high pressure torsion method (HPT). This process belongs to the group of intensive plastic deformation methods (SPD). SPD methods are in the centre of scientific interest for several decades. Theoretical part of this thesis puts an effort to summarize basic knowledge and principles of SPD methods with extra focus on method HPT. As theoretical part continues magnesium as technical material is presented. Influence of SPD on use and properties of pure magnesium is then presented. This trend is further developed in effort to describe the effect of individual HPT process variables on the properties of pure magnesium and its alloys. Focus of practical part of this thesis is in influence of number of revolutions. Samples were processed at 1/8, 1/4, 1/2, 1, 4 and 8 turns at room temperature. Speed of process was 1rpm and applied pressure was 6 GPa. The structure of commercially pure magnesium prepared by casting and moulding were observed with focus on differences caused by input material. The structure was observed by both light microscopy and back scattered electron diffraction (EBSD), focusing on structure development, grain size and grain orientation. Compared to other works on similar topic, the emphasis here is on observing the microhardness on the vertical edge of the sample. The hardness shows a steep increase right after 1/8 of a turn. With increasing number of turns gradual homogenization of microhardness is presented accompanied by slight decrease in microhardness. No trend in microhardness relative to the distance from anvil has occurred. Structure observed with EBSD shows a bimodal character with larger grains oriented in the same direction. The three-point bending test didn’t end up as expected, and the approach to evaluation of magnesium-based HPT needs to be re-evaluated for future work. A three-point bending test was designed for the initial assessment of the basic mechanical properties of the material.
|
|
|
Influence of severe plastic deformation and subsequent annealing on creep behaviour of martensitic 9% Cr steel
Král, Petr ; Dvořák, Jiří ; Sklenička, Václav ; Horita, Z. ; Tokizawa, Y. ; Tang, Y. ; Kunčická, Lenka ; Kuchařová, Květa ; Kvapilová, Marie ; Svobodová, M.
The objective of the study is to evaluate the effects of severe plastic deformation (SPD) and annealing on creep behaviour of advanced tungsten modified creep-resistant 9 % Cr martensitic P92 steel. The as-received P92 steel was deformed by high-pressure torsion (HTP), high-pressure sliding (HPS) and rotary swaging (RS) at room temperature prior creep testing. These SPD methods imposed significantly different equivalent plastic strain in the range from 1 up to 20. Constant load creep tests in tension were performed in an argon atmosphere at 873 K and applied stress ranging from 50 to 200 MPa. The microstructure and phase composition of P92 steel were studied using a scanning electron microscope Tescan Lyra 3 and a transmission electron microscope Jeol 2100F. The results show that under the same creep loading conditions the HPT and HPS-processed P92 steel exhibited significantly faster minimum creep rates, creep fracture strain and the decrease in the value of the stress exponent of the creep rate in comparison with as-received P92 steel. However, it was revealed that the RS-processed specimens exhibited one order of magnitude lower minimum creep rate and lower ductility compared to commercial P92 steel. The creep curves for the HPT and HPS-processed states exhibited a pronounced minimum of strain rate. The pronounced minimum of strain rate disappeared when these states were annealed at 923K/500h before application of creep loading. The microstructure changes occurring during creep and different creep behaviour between as-received and deformed states are discussed.
|
|
|
Study of ultrafine-grained materials prepared with different methods of severe plastic deformation
Krajňák, Tomáš ; Mathis, Kristián (advisor) ; Hadzima, Branislav (referee) ; Kalvoda, Ladislav (referee)
Title: Study of ultrafine-grained materials prepared with different methods of severe plastic deformation Author: RNDr. Tomáš Krajňák Department: Department of Physics of Materials, Faculty of Mathematics and Physics, Charles University in Prague Supervisor: Doc. RNDr. Kristián Máthis, PhD., Department of Physics of Materials, Faculty of Mathematics and Physics, Charles University in Prague Abstract: Interstitial free steel with ultrafine-grained (UFG) structure was prepared by high-pressure torsion (HPT). The development of the microstructure as a function of the number of HPT turns was studied at the centre, half-radius and periphery of the HPT-processed disks by X-ray line profile analysis (XLPA), positron annihilation spectroscopy (PAS) and electron microscopy. The dislocation densities and the dislocation cell sizes determined by XLPA were found to be in good agreement with those obtained by PAS. The evolution of the dislocation density, the dislocation cell and grain sizes, the vacancy cluster size, as well as the high-angle grain boundary (HAGB) fraction was determined as a function of the equivalent strain. It was found that first the dislocation density saturated, then the dislocation cell size reached its minimum value and finally the grain size got saturated. For very high strains after the...
|
|
|
Mechanical and physical properties of magnesium alloys prepared by rotary swaging
Škraban, Tomáš ; Drozd, Zdeněk (advisor) ; Mathis, Kristián (referee)
in english For their positive influence on mechanical and physical properties of the material, methods of severe plastic deformation are popular for quite some time today. Rotary swaging is one of them. With its simplicity and productivity, it has the potential for industrial use. It is a radial swaging of rods or tubes, which results in decreasing of their diameter. Influence of this method is researched on extruded rods made of magnesium alloy AZ31. Experiments are made on five samples of different degree of swaging (different diameter). This allows to research gradual evolution of properties during the swaging. Results show significant positive influence on grain size (and microstructure in general) of originally extruded rod. During swaging there is an evolution of material texture and increase in strength.
|
|
|
Microstructure and mechanical properties of lightweight structural AZ31 alloy prepared by twin-roll casting method.
Zimina, Mariia ; Cieslar, Miroslav (advisor)
Title: Microstructure and mechanical properties of lightweight structural AZ31 alloy prepared by twin-roll casting method Author: Mariia Zimina Abstract: Microstructure of AZ31 twin-roll cast magnesium alloy was studied using light optical, electron and atomic force microscopy. The effect of annealing temperature on the microstructure was tested. Mechanical properties of a thin magnesium strip were investigated by means of microhardness tests and tensile tests at a relatively low strain rate 10-3 s-1 . Results show that the ductility of the twin roll cast strip increases with increasing deformation temperature, however, a remarkable decrease was observed at about 200 řC. This effect appears also in a conventionally cast ingot of a master alloy and is caused by a change of a deformation mode occurring at this temperature. Moreover, the effect of severe plastic deformation on the microstructure and mechanical properties was studied. Equal channel angular pressing was applied on magnesium strip samples and lead to a significant grain refinement accompanied by an unfavorable strengthening of the initial basal texture, which is effectively suppressed by a subsequent annealing. A constrained groove pressing was for the first time successfully applied on AZ31 twin-roll cast strip leading to an increase of...
|
|
|
Mechanical and physical properties of magnesium alloys prepared by rotary swaging
Škraban, Tomáš ; Drozd, Zdeněk (advisor) ; Mathis, Kristián (referee)
in english For their positive influence on mechanical and physical properties of the material, methods of severe plastic deformation are popular for quite some time today. Rotary swaging is one of them. With its simplicity and productivity, it has the potential for industrial use. It is a radial swaging of rods or tubes, which results in decreasing of their diameter. Influence of this method is researched on extruded rods made of magnesium alloy AZ31. Experiments are made on five samples of different degree of swaging (different diameter). This allows to research gradual evolution of properties during the swaging. Results show significant positive influence on grain size (and microstructure in general) of originally extruded rod. During swaging there is an evolution of material texture and increase in strength.
|
|
|
Structure and mechanical properties of magnesium materials processed by HPT
Poloprudský, Jakub ; Němec, Karel (referee) ; Doležal, Pavel (advisor)
This thesis is focused on processing of pure magnesium by high pressure torsion method (HPT). This process belongs to the group of intensive plastic deformation methods (SPD). SPD methods are in the centre of scientific interest for several decades. Theoretical part of this thesis puts an effort to summarize basic knowledge and principles of SPD methods with extra focus on method HPT. As theoretical part continues magnesium as technical material is presented. Influence of SPD on use and properties of pure magnesium is then presented. This trend is further developed in effort to describe the effect of individual HPT process variables on the properties of pure magnesium and its alloys. Focus of practical part of this thesis is in influence of number of revolutions. Samples were processed at 1/8, 1/4, 1/2, 1, 4 and 8 turns at room temperature. Speed of process was 1rpm and applied pressure was 6 GPa. The structure of commercially pure magnesium prepared by casting and moulding were observed with focus on differences caused by input material. The structure was observed by both light microscopy and back scattered electron diffraction (EBSD), focusing on structure development, grain size and grain orientation. Compared to other works on similar topic, the emphasis here is on observing the microhardness on the vertical edge of the sample. The hardness shows a steep increase right after 1/8 of a turn. With increasing number of turns gradual homogenization of microhardness is presented accompanied by slight decrease in microhardness. No trend in microhardness relative to the distance from anvil has occurred. Structure observed with EBSD shows a bimodal character with larger grains oriented in the same direction. The three-point bending test didn’t end up as expected, and the approach to evaluation of magnesium-based HPT needs to be re-evaluated for future work. A three-point bending test was designed for the initial assessment of the basic mechanical properties of the material.
|
|
|
Microstructure and thermal stability of ultra fine grained Mg-Zn-Y alloys
Vlasák, Tomáš ; Čížek, Jakub (advisor) ; Procházka, Ivan (referee)
The aim of this diploma thesis is to investigate microstructure and thermal stability of ultra fine grained magnesium alloys. The thesis first summarises methods using plastic deformation in order to achieve ultra fine grained structure that are used to process metals. Then experimental methods employed in the experimental part including microhardness testing, scanning electron microscopy and positron annihilation spectroscopy are described. Brief summary of previous research on MgZnY alloys strengthened by quasicrystalline phases and Mg22Gd alloys is given. Finally, results of experimental investigation of MgZnY alloys with various Zn/Y ratios and Mg22Gd alloy are discussed. These results suggest that presence of phases in MgZnY alloys depend on Zn/Y ratio, hardness of these alloys depends on Zn content and that rapid cooling of MgZnY alloys annealed at 500 řC lead to significant increase in volume fraction of quasicrystalline icosahedral phase. In the second section of the experimental part thermal behaviour of Mg22Gd alloy is investigated. Furthermore, formation of GdH2 particles in Mg22Gd is examined and attributed to reaction of hydrogen decomposed from water vapour with gadolinium in areas rich in gadolinium. Finally, significant hardening of Mg22Gd alloy processed by high pressure torsion has been...
|
|
|
Microstructure and mechanical properties of lightweight structural AZ31 alloy prepared by twin-roll casting method.
Zimina, Mariia ; Cieslar, Miroslav (advisor) ; Málek, Jaroslav (referee) ; Novák, Pavel (referee)
Title: Microstructure and mechanical properties of lightweight structural AZ31 alloy prepared by twin-roll casting method Author: Mariia Zimina Abstract: Microstructure of AZ31 twin-roll cast magnesium alloy was studied using light optical, electron and atomic force microscopy. The effect of annealing temperature on the microstructure was tested. Mechanical properties of a thin magnesium strip were investigated by means of microhardness tests and tensile tests at a relatively low strain rate 10-3 s-1 . Results show that the ductility of the twin roll cast strip increases with increasing deformation temperature, however, a remarkable decrease was observed at about 200 řC. This effect appears also in a conventionally cast ingot of a master alloy and is caused by a change of a deformation mode occurring at this temperature. Moreover, the effect of severe plastic deformation on the microstructure and mechanical properties was studied. Equal channel angular pressing was applied on magnesium strip samples and lead to a significant grain refinement accompanied by an unfavorable strengthening of the initial basal texture, which is effectively suppressed by a subsequent annealing. A constrained groove pressing was for the first time successfully applied on AZ31 twin-roll cast strip leading to an increase of...
|
guest ::
