|
|
Planar Structures for High Frequency Band
Pulec, Jiří ; Pietriková, Alena (referee) ; Maschke, Jan (referee) ; Szendiuch, Ivan (advisor)
The present paper deals with the problematics of the design and technology of planar microelectronic structures for the hign frequency band. These structures were realised on the Department of Microelectronics and their properties were measured on the Department of Radioelectronics. The part of this work is also simulation of some microelectronic structures, where for these simulations the design and simulation tool Ansoft Designer and the FEM tool ANSYS was used. The attention is paid to the discrete devices (coils and capacitors) as well as to the more complex structures (frequency filters). The paper yields the new findings in the field of the design and technology of the discrete components as well as of the more complex systems, these findings can be used as the basis for another research of practical applications.
|
|
|
Description Methods for Electrical Systems and Their Solving
Křižka, Jakub ; Němec, Zdeněk (referee) ; Šeda, Miloš (advisor)
The objective of bachelor thesis is a searching description of methods, which are usually used for calculation of circuit variable values in electric circuits. At the beginning is thesis concerning with description of individual components (power supplies, electronic components) used in electric circuits, then also with analysis of rules, which are the fundamental for a calculation of values in electronic circuit – Ohm’s rule and Kirchhoff’s rules. Indivisible part of thesis is also summary of special methods, such as method of loop currents (mesh analysis), method of nodal voltage (nodal analysis) etc. and their demonstration on examples of electric circuits. The structure of thesis is coursebook and gives successive summary of information in area calculations of electric circuits.
|
|
|
Electronic equipment for high-power flash light
Fritsch, Karel ; Folprecht, Martin (referee) ; Knobloch, Jan (advisor)
Point of this thesis is introduction to topology of small power switching power supplies and final application of gained knowledge during development of converter for charging capacitor battery of high power photographic flash. Thesis also contains design of control unit with microcontroller and description of work process of activation individual function blocks.
|
|
|
Utilization of local systems for power system regulation
Kostov, Jiří ; Geschwinder, Lukáš (referee) ; Bartošík, Tomáš (advisor)
Bachelor’s Thesis deals general information about methods of regulation of elektrification systems, including basic principles of regulation of frequency, regulation of voltage and regulation of reactive and active power. Work includes information about aggregate remote control system, power plants that participate on regulation and self device for regulation and controlling of reactive power. Work engages on new options in section of regulation and his requirements for distribution sites. Part of work deals information about renewable natural energy sources and his requirements for distribution sites.
|
|
| |
|
|
Local characterization of electronic devices
Müller, Pavel ; Škarvada, Pavel (referee) ; Tománek, Pavel (advisor)
The development of micro and nanoelectronics and nanophotonics needs novel characterization techniques to ensure higher quality of designed devices. The thesis describes a use of Scanning Near-field Optical Microscopy (SNOM) in dimensional control and in local investigation of diverse physical parameters. As example of its potential, the correlation between object topography and reflection measurement of capacitors is shown.
|
|
|
Active electrical filters based on switched-capacitor circuits
Třeček, Stanislav ; Dostál, Tomáš (referee) ; Brančík, Lubomír (advisor)
This thesis deals with concept of universal frequency filter by application of a switched-capacitor functional block. The concept is based on the theory of switched-capacitor circuits and the theory of a design of classical frequency filters. The printed circuit board was designed based on the filter connection developed by using a software Eagle. The filter was implemented as a laboratory product. This product has been revitalized and the frequency response of all types of filters has been measured. The measured parameters were compared with the parameters set out in the technical documentation of functional block.
|
|
|
Single-Phase Induction Motor Calculation
Ševčík, Pavel ; Vítek, Ondřej (referee) ; Hájek, Vítězslav (advisor)
This master's thesis considers by single-phase asynchronous motor. The first part discuss about construction, principle of operation and basic parameters of this motor type. It also discussed the emergence of torque and torque characteristics of the different types of engines. The second part explains the basic ways of obtaining grip moment including outline the principles of functions particulars constructions types, which is produce in practice. In the third part is minutely analyse single-phase asynchronous motor with auxiliary phase and permanently conect capacitor, including method of assign size of a capacitor. Fourth part section provides the principles of the procedure for calculating basic parameters of the single asynchronous motor with auxiliary phase. At the last part is accomplished a calculation of single-phase asynchronous motor with permanently conect capacitor at auxiliary phase including comparation with already manufacturing motor.
|
|
| |
|
|
Tvorba hybridní aplikace využívající mapové podklady
Plíšková, Tereza
This diploma thesis deals with the design, implementation and deployment of a hybrid application that is based on maps. This hybrid application was created on the basis of an already existing web application with the use of modern technologies. It should be used for easy traffic monitoring of selected parts of cycle routes. Part of this thesis is also development of REST API for retrieving data from database server.
|
guest ::
