|
|
Measurement of the vibrations
Diblík, Jan ; Kolouch, Jaromír (referee) ; Biolková, Viera (advisor)
Diploma thesis is focused on principles of measuring the vibrations using accelerometers and using them for making vibration measuring instrument with focus on modern integrated digital accelerometers. In the first part are described ways to measure acceleration and vibrations with available technical supplies with respecting place and purpose of measuring. In practical part are measured characteristics of used sensor, instrument for measuring vibrations is designed and built and for few experimental object vibrations or acceleration are measured and graphical interpreted.
|
|
|
Design and realization stereophonic amplifier class D
Hradil, Jaroslav ; Háze, Jiří (referee) ; Pavlík, Michal (advisor)
The aim of this project is to design a class D stereo audio amplifier with output power of 2 x 50 W into 4 load with THD+N less than 10%. Project is divided into three parts. First part describes the principles of class D amplifiers, the second part contains actual design of amplifier and the last part presents the results of the measurements.
|
|
|
Power audio amplifier with AC/DC converter
Melša, Vojtěch ; Kováč, Michal (referee) ; Kubíček, Michal (advisor)
The aim of this work was to design and construct a simple audio amplifier, which would be based of involvement and components used in switching power sources on the maximum degree (for example from usual ATX sources for computer). The main motivation for development is the existence of many old sources that do not use and big interest of users for the construction of home audio amplifiers for small and medium power. Amplifiers based on switching power sources with greater efficiency and less weight than comparable classic amplifiers (working in classes A, B or AB). Their disadvantage is the complicated design and introduction of distortion and spurious signals to the amplified signal. This work will be described a design of simple amplifier, which will minimize these negative effects. For shortcomings and wrong parameters this proposed involvement will be eventually described and implemented design of amplifier in class D.
|
|
|
AC power supply with remote control
Štěpnička, Martin ; Papica, Petr (referee) ; Kubíček, Michal (advisor)
The project describes the design of controlled inverters or power generator simulating one phase of European or American distribution network. The generator is able to enter into an output signal of a certain fault conditions designed to testing the electromagnetic compatibility of connected devices. The text is divided into three main chapters. The first one deals with the design of the power generating low-frequency signal. The second part describes the power source used for this generator. In the third section describes the program management unit. End of text summarizes the results. The annex contains a schematic designs and printed circuit boards.
|
|
|
Laboratory module for educational purposes
Tuhý, Luboš ; Vašíček, Adam (referee) ; Procházka, Petr (advisor)
This thesis describes the design and implementation of the transistor inverter to the subject of power electronics first outcome of this thesis will transistorized inverter that will serve as a demonstration tool in laboratory practice course electrical power. The laboratory preparation, students will be able to virtually test your theory acquired knowledge of the issue. Part of the theoretical analysis will be proposed circuit simulation program through classes Spice.
|
|
|
Digital audio amplifier
Tiller, Jakub ; Kratochvíl, Tomáš (referee) ; Dřínovský, Jiří (advisor)
The subject of bachelor thesis is the class-D power audio amplifiers. Their expansion is mainly caused by high efficiency and good audio parameters. The aim of this project is analysis of class-D amplifiers and measurement of the audio parameters. In consequence, there is the design of class-D apmlifier as laboratory equipment with possibility of digital gain controll. At the end of this thesis, there are designs of automatic measurment in VEE Pro environment. The laboratory exercise also introduced in this thesis.
|
|
|
Controler for brushless motors
Zdařil, Tomáš ; Bradáč, Zdeněk (referee) ; Kincl, Zdeněk (advisor)
The goal of the thesis was to design and create one-way speed controler for brushless DC motors, that is used in air modeling. The function is based on the without sensors control method and circuit is controlled by the Atmel AVR. Power unit for motor is used Li – pol accumulator. The controller is equipped with a BEC to power the receiver and allows monitoring current and voltage on the accumulator. The measured data can be uploaded to a PC.
|
|
|
Multipurpose power supply for electroplating system
Pinďák, Michal ; Vorel, Pavel (referee) ; Procházka, Petr (advisor)
The aim of the bachelor thesis is the practical proposal of the multipurpose power supply for the electroplating system. The individual technological processes of electroplating, for which the parameters of the source have to be adapted, are presented in the theoretical part. This part includes the entire division of pulse DC/DC converters without a transformer from the aspect of working quadrants and finally the ways of their controlling. There is also introduced the analysis of parameters of the presumed DC power supply XP Power HDS3000PS60. The conclusion of the thesis is focused on the entire proposal of converter wiring, its construction and subsequent commissioning through the software LabVIEW.
|
|
|
Ultrasonic Directional Speaker
Sedlák, Jiří ; Michalec, Jaroslav (referee) ; Mikulka, Jan (advisor)
The master´s thesis deals with theoretical research and practical application of the principle of spreading acoustic waves through nonlinear medium. The theoretical part describes five different types of amplitude modulation and their mathematic representation, which were verified by the program Matlab. Next, the impedance characteristic of ultrasound PZT transducer was measured and the design of PWM modulator and class D amplifier was described. The practical part of the master´s thesis contains the realization of the parametric loudspeaker assembled from the class D amplifier and the PWM modulator. In conclusion, the designed parametric loudspeaker was measured and the individual types of amplitude modulation were compared with respect to the total harmonic distortion of transmitted useful signal.
|
|
| |
guest ::
