|
|
Uncertainty Evaluation in Photometry and Radiometry
Motyčka, Martin ; Bálský,, Marek (referee) ; Gašparovský,, Dionýz (referee) ; Škoda, Jan (advisor)
This dissertation thesis is focused on the uncertainty analysis of the spectroradiometric and photometric measurements. The measurement uncertainty should be stated in every measurement protocols or calibration certificates. Recently the luminance cameras are widely used for the luminance measurements in the whole scene with a good resolution and measuring time. However, there is no uncertainty estimation method for these measuring devices. Therefore, this thesis analyses the luminance measurement uncertainty of the luminance analyser LDA – LumiDISP, that can be classed as a luminance camera. Since the calibration procedure is very complicated and traceable to other measuring photometric devices, there is a detailed description of the measurement uncertainties of luxmeters, luminance meters, spectroradiometric systems and its practical calculations for these systems in the light laboratory FEKT Brno University of Technology. However, the measurement uncertainties estimation of the spectroradiometric systems is especially difficult for the output quantities calculated from the spectral power distribution of the light source. In this thesis there is presented a method of uncertainty measurement and estimation of these spectroradiometric systems and luminance analyser LDA, where the luminance measurement uncertainty varies with the measured spectral power distribution of the light source, its position in the luminance image and the exposure settings.
|
|
| |
|
| |
|
|
Photometry and spectroradiometry of LEDs
Vysoudil, Martin ; Škoda, Jan (referee) ; Drápela, Jiří (advisor)
This thesis deals with the processing of light technical parameters and performance of key LED chips for their applications in lighting systems. The aim is to create a laboratory model for measuring the qualitative and quantitative parameters of highly luminous light LED emitted depending on the angle, using a spherical integrator 0.3 m, goniometer and fiber spektroradiometr /luxmeters. Goniometer is designed using modular optomechanical parts company Thorlabs. Due to the current passing through the LED chips heat up considerably. To light LED chip parameters tested were not affected by heat from the chip is required to pay the heat generated by a passive radiator. Another part of this thesis is the reconstruction of an older model spherical integrator. Reconstruction must be undertaken so as to ensure sufficient cooling again tested LEDs. Light scattered in the ball of the integrator is led by the optical cable to the spektroradiometr that are subsequently recorded its parameters. The second element used to measure the light produced by the LED source is photocell. Spherical integrator must be appropriately modified to indicate the two measuring elements and also meet the standards of determining the correctness of measurement. At the end of the measurement results will be compared with catalog values provided by the manufacturer.
|
|
|
Industrial Tester for Photometric Values of LED diodes Used in Automotive Signal Lighting
Gaži, Dominik ; Froehling, Kenneth (referee) ; Baumgartnerová, Alena (advisor)
V posledních letech zažili světlomety v autech obrovský technický rozvoj, který se podílel na jejich současné složitosti. Aby řidiči i zákazníci byli spokojeni, je využíváno různých technologií pro neustálé dosahování účinnějších a bezpečnějších světelných zdrojů. Společnosti usilují o minimalizaci ztrát ve výrobě ve snaze šetřit životní prostředí a konat ekonomicky. Tato práce se zabývá výzkumem osvětlovací techniky a návrhem jednoduchého a efektivního zařízení pro testovaní chyb LED plošných obvodů ve světlometech, to vše za účelem minimalizace strat. Dalším cílem je výzkum možností konstrukce takového zařízení z technologického hlediska.
|
|
|
Technology of pouring LED strips with epoxy materials
Rudy, Veronika ; Krejčí, Miroslav (referee) ; Píška, Miroslav (advisor)
The thesis deals with the pouring of epoxy materials over LED strips. The research part contains an introduction to photometry and summarizes the types of potting compounds along with their characteristics. The practical part delves into the effect different amount of pigment has on the photometric properties. This is assessed based on verified measurements performed with the help of a goniophotometer on samples with different amounts of pigment, which were created using an integration sphere. Furthermore, a brightness analysis and a long-term outdoor test were performed.
|
|
|
Printed light dosimeter for galleries
Škarvadová, Adéla ; Klusoň, Petr (referee) ; Veselý, Michal (advisor)
This bachelor thesis deals with the lighting of the gallery space and the measurement of light intensity inside. The subject of the experimental study are photosensitive composition for the production of disposable printed and thin-film dosimeters for galleries and museums. Kinetic color change of the two systems using two dyes and calibration components was examined. The composition for printing was optimized and dosimeters were prepared with a wide range of light exposure causing a significant color change of the dosimeter, and that from 1,7 klx•h to 200 klx•h.
|
|
|
Design and construction of an interactive light sources panel
Žák, Martin ; Pavelka, Tomáš (referee) ; Škoda, Jan (advisor)
This semestral thesis deals with design and construction of the interactive light sources board and measurement of various parameters of those light sources. Using the given requirements, a solution is worked out (construction materials, behaviour, design, wiring etc. are given). Based on this, the interactive board was also constructed and put into operation. The thesis is also focused on the given light sources themselves (incandescent light bulbs, halogen lamps, compact fluorescent lamps, fluorescent tubes and LED lamps) and their measurement results are presented.
|
|
|
Design of demonstration suitcase with light sources
Vojkůvka, Jan ; Baxant, Petr (referee) ; Škoda, Jan (advisor)
This bachelor thesis deals with the design and realization of a demonstration case with light sources. The work explains the basic photometric parameters, contains the measurement of the reflectivity of samples. Furthermore, the work describes the design process, process of realization of the demonstration case, selection of light sources and brightness measurements performed on the finished demonstration case.
|
|
| |
guest ::
