|
|
Research of the reliability of lead-free solder joints
Pelc, Miroslav ; Švecová, Olga (referee) ; Szendiuch, Ivan (advisor)
This work deals research of the reliability of leed-free solder joints. It summarizes the basic knowledge of lead-free solder alloys, soldering and testing process, the soldered joints. The work is done selecting the most important factors entering into the soldering process. The method of the DOE sought the optimal combination of factors, which would correspond to the highest quality solder joints.
|
|
|
Lead-Free solder thermal and microstructure analysis
Klepárníková, Eliška ; Molliková, Eva (referee) ; Jan, Vít (advisor)
The bachelor thesis deals with Ag-Sn-Sb system, construction of pseudobinary diagram 90An10Sb – 90Sn10Sb and construction of ternary diagram at 20 C. The theoretical part deals with soldering, phase diagrams and methodics of determination of phase diagrams. The experimental part is focused on describing the creation of five alloys and their further exploration. Alloy analyzes were performed by differential scanning calorimetry (DSC), light microscope and scanning electron microscope. Results from these thermal and microstructural analyzes were processed into the resulting pseudobinary and ternary diagram.
|
|
|
The possibilities of SMD components soldering by equipment Fritsch
Juračka, Martin ; Šandera, Josef (referee) ; Adámek, Martin (advisor)
This thesis focuses on soldering technology in microelectronics. It describes in detail the basic ways of soldering and repairs in electronics. This piece of work shows the principles of technological equipment for bulk soldering and used repairing devices. In the theoretical part of this work there are also briefly described the packages for integrated circuits that were used in the practical part of the thesis. The practical part of the thesis deals with setting of the heat profiles for hot air repair station Fritsch Mikroplacer for LQFP64, SOIC16, TSSOP14, QFN16 and DSBGA5 packages. The heat profiles for assembly and disassembly of the particular types of the packages on designed and manufactured test printed circuit board were set and tested. The resulting heat profiles are compared with the recommended heat profile of an ordinary solder paste SnAg3Cu0,5 which was used for the test. This thesis can serve as an aid for the further settings of heat profiles in other types of packages not only on Fritsch Mikroplacer devices, but also on other repairing devices of this type.
|
|
|
Optimalization of repair process in Surface Mount Technology
Vala, Radek ; Řezníček, Michal (referee) ; Szendiuch, Ivan (advisor)
This project deals with utilizing of IR 400 equipment for assembly and repair of SMD components soldered by lead-free solder materials. The part of the work concerns with optimizing of the temperature profile, which is very important in the repair to eliminate the damage of components and PCB. There was added controller R 500 and cooling equipment to allow better control of the temperature during the soldering cycle.
|
|
|
Testing of Solders in Protection Atmosphere
Vala, Radek ; Jankovský, Jaroslav (referee) ; Szendiuch, Ivan (advisor)
The project deals with the overall design and construction of equipment called the desiccators for brazing in a protective atmosphere. The device was designed and manufactured cooling and heating element. For the soldering various temperature profiles have been defined and adjusted, as for SnPb as well for lead-free solders. There was a realization of samples were measured and analyzed. Finally were realized micro sections for lead free solder.
|
|
| |
|
|
Research of the Quality of Solder Joints by BGA and QFN Packages
Otáhal, Alexandr ; Adámek, Martin (referee) ; Szendiuch, Ivan (advisor)
This diplomas thesis deals with specific technologies and manufacture of BGA and QFN packages. Also summarizes the most used test methods for assessing the reliability for. Describes the making of equipment for soldering in a nitrogen atmosphere, followed by comparison solder joints of BGA and QFN forming in different atmosphere. Finally, summarizes knowledge about the process of soldering and desoldering lead-free solders for BGA packages, followed by experimental evaluation of the causes of malfunction of repaired samples.
|
|
|
Thermal aging of lead-free low-temperature joints
Jansa, Vojtěch ; Šandera, Josef (referee) ; Adámek, Martin (advisor)
The aim of this masterś thesis is to investigate properties of lead-free low-temperature solders after termal aging. The theoretical part is focused on various types of lead - free solders, pastes used for the manufacture of electrical circuits by thick-film technology and methods of testing the properties of the soldered joints. The practical part deals with the design and production of test substrates for testing the solder joints formed between the SMD component and the ceramic substrate. Two solder bismuth-containing solder was selected for testing, the SAC solder was selected as the reference. After aging with temperature cycling from -30 ° C to 115 ° C, the data obtained by testing the mechanical strength of the solder joint by the shear test is evaluated.
|
|
|
The analysis of Cu-Sn-Sb ternary alloy
Kučera, Jan ; Doubrava, Marek (referee) ; Jan, Vít (advisor)
This bacholor thesis deals with substituting silver-based material, currently used for experimental semi-liquid extrusion. The proposed material is from the Cu-Sb-Sn system. The theoretical part of the work deals with soldering and phase diagrams. The experimental part is devoted to the analysis of three proposed alloys from the Cu-Sb-Sn system, their structural and mechanical properties. Thermal analyzes of the alloys were performed using differential scanning calorimetry (DSC), the microstructure using a light microscope and a scanning electron microscope, and a hardness tester was also used to determine the hardness. The results are summarized in the discussion.
|
|
| |
guest ::
