|
|
Design of audio frequency amplifier for PC sound card
Chalupa, Petr ; Bajer, Arnošt (referee) ; Musil, Vladislav (advisor)
This work deals with the problems of low frequency amplifiers that are specialised in processing an analog music signal, that is get from output element of an sound card of an computer. A part of my work is a design of an amplifier, an design verification by calculations and simulations and subsequent production of amplifier. The end of my work is specialised in measurement parametres of amplifier and comparing them with german norm DIN 45 500.
|
|
|
Construction of class T audio amplifier
Tejmlová, Lenka ; Slezák, Josef (referee) ; Petržela, Jiří (advisor)
The aim of my bachelor’s thesis is to collect information about amplifiers, working in the T class. Because these amplifiers are usually used as digital power processing audio amplifiers, we mostly insist on the ability of sending, the signal without distortion, to amplify the frequency broadband signal, to obtain the high efficiency of the output stages and to obtain the peak quality of the sound. My task is to gather information and facts of principle of the function of the audio amplifiers working in the T class and reasonably priced integrated circuits of this class. Furthermore I am going to focus on the design of wiring of this amplifier with the 2x20 watts output, including the correction pre-amplifier, which provides correction of the heights, basses and volume. The amplifier is realized, in the end of bachelor’s thesis, there are measured it’s characteristics, which are compared to theory.
|
|
|
Class AB audio amplifier for two satellites and subwoofer
Cupák, Jan ; Brančík, Lubomír (referee) ; Kratochvíl, Tomáš (advisor)
This bachelor’s thesis deals with design of AB class audio amplifiers. Further more it deals also with other functional blocks, e.g. preamplifier, tone equalizer and active crossover. Outcome of this work is a complete solution of the amplifier with it's simulation. In final solution is also included scheme of a high quality power supply unit, speaker protection and heat sinks for high performance transistors. In this project is also included a solution of task about optimal mechanical arrangement of the single parts in the case of this amplifier. This thesis contains results of measurement and photo document of functional prototype.
|
|
|
Class D audio amplifier with PWM modulation
Arvai, Luboš ; Petržela, Jiří (referee) ; Kratochvíl, Tomáš (advisor)
The aim of this project is design audio amplifier working in class D with power output 2x20 W. In the beginning is shortly described a principle of amplifiers in class D. In the next chapter is block circuit diagram and requirements list for individual blocks. In next section is closely described circuit design of correction preamplifier, PWM modulator with driver of power transistors, power stage and output filter. At the conclusion is summarized experimentally obtained knowledge. On the basis of this knowledge is described modification of original design.
|
|
|
Class D audio amplifier for active loudspeakers
Cupák, Jan ; Punčochář, Josef (referee) ; Kratochvíl, Tomáš (advisor)
This master's thesis deals with design of D class audio final amplifier, which was output power 400 W for 4 ? load impedance. Designed audio amplifier is specifical for active speaker, which consists of satelite speakers and subwoofer. Further more it deals also with other functional blocks, e.g. balanced input preamplifier, active crossover and protection for safety running. Outcome of this work are schemes of each functional blocks of D class audio amplifier, whose functionality was verified by simulation. Thesis also contains full reference material including mechanical arrangement of functional blocks on printed connection board. The conclusion contains the measured parameters of function blocks of produced prototype and complete photographic documentation.
|
|
|
Design of nf electron-valve stereo amplifier
Dofek, Přemysl ; Rampl, Ivan (referee) ; Káňa, Ladislav (advisor)
This master’s thesis is dealing with low frequency all valve stereo amplifier unit conception for an electric guitar. The amplifier contains two independent output stages with two power tubes EL34, working in AB class, with 40Watts of power. The apparatus is equipped with two channels, EQ correctors, parallel effects loop, output selection with lowered anode power supply, selection between silicon or tube rectifier. The preamplifier works in mono mode and the stereophony is reached by dividing the signal in an added effects system. This unusual solution differs from both monaural conceptions and binaural power amplifiers which contains no preamp. It offers the possibility of stereophony without the necessity of dividing the guitar signal before the amplifier’s input. The sound that comes from the speaker on one side is effected and on the other side is dry by using monaural effects apparatus. The sound from both speakers is effected by using binaural effect apparatus. The amplifier can be used as power amplifier stage only when the return of the effect loop is used as the amplifier input. Every available possible solution is discussed in case of each block and then the most suitable is chosen. The biggest attention is paid to a proposal and calculation of both power and output transformer, ergonomical lay-out of the stages in need of the best S/N separation. The stages were simulated in Micro-Cap 9.0 and Tonestack 1.3 computer programmes. The construction was carried out with the emphasis on proper shielding and grounding. The overall stability tests were performed after building the amplifier as well as frequency characteristics with the scope and distortion with the distortion meter.
|
|
|
Design of switching-mode audio power amplifier
Svadbík, Vít ; Sutorý, Tomáš (referee) ; Brančík, Lubomír (advisor)
This work describes the design of audio amplifiers operating in switching mode. The first part describes basic principles of the power stage switching concept. There is described differences between classes of amplifiers according to technology. The second larger part includes design and construction of the switching amplifiers. Design is implemented, including the preamplifier and power supply. Power supply works in switching mode. The measured parameters of the proposed facility are given in the last part.
|
|
|
Controlled power generator of current impulses
Gabriel, Viktor ; Vrba, Kamil (referee) ; Rampl, Ivan (advisor)
The goal of this thesis is to design and realise microprocessor-controlled generator of current impulses, which are being brought in induction load. Thesis contains description of individual functional generator parts, mainly microprocessor program equipment. The text also aims for inductor design as an induction load and other solutions of power parts with the selection of the most suitable one. The generator of current impulses itself is realised on two-sided printed circuit board.
|
|
|
Design and making of low-frequency power amplifier in class AB
Dušek, Martin ; Kratochvíl, Tomáš (referee) ; Brančík, Lubomír (advisor)
In this bachelor thesis I am occupied with low frequency amplifiers, theirs important parameters, classes and with integrations end-level. Next I am occupied with miscellaneous types of preamplifiers and additional circuits. There are simulated schemes of corrective preamplifier, protections scheme and high power amplifier in PSpice software in this thesis. These schemes and next additional modules are connected with DPS. This thesis contains result of measurement and photo functional sample.
|
|
|
The construction of a vacuum tube amplifier
STREJC, Jakub
The presented thesis describes the construction of a tube amplifier in both theoretical and practical ways. The aim of this work was to construct a functional tube amplifier with an output of at least 2 x 20 W. The first part of the study describes the theoretical background of tube amplifiers which are recognized for their characteristic sound. Wiring diagrams for each block and other functional blocks of the amplifier, such as headphones or VU meter connections, are discussed. The last part of the thesis focuses on the actual realization of the tube amplifier.
|
guest ::
