|
|
Electronic controlled glow for water hookah
Rumíšek, Tomáš ; Šebesta, Jiří (referee) ; Fedra, Zbyněk (advisor)
This bachelor thesis deals with the substitution of a standard charcoal heating system for an electronically-controlled heating element in a hookah. The heating element temperature is regulated by the Atmel microprocessor, depending on the temperature specified by an user. The user can adjust the desired temperature on a control panel, where also the actual temperature of the heating element will be displayed.
|
|
| |
|
|
Adjustable source feeded and controlled by USB bus
Staněk, Miroslav ; Frýza, Tomáš (referee) ; Kolouch, Jaromír (advisor)
The aim of this bachelor’s thesis is concept and realization of voltage source which is controlled and feeded by Universal Serial Bus. There will be presented whole design, execution, development progress and finalization of this project in the following text. This source must boost and buck standard voltage from USB. So it will be necessary using two source lines. Microcontroller of AVR family will be used in the direct part of this adjustable source. Into this microcontroller will be embedded USB interface by the software solution. The microcontroller isn‘t used only for communication with PC by the computer programme, but it is also used for switching the source lines by the PWM modulation. According to the minimum output voltage scale (0 – 15 V) this source is useful for a wide spectrum of low- power devices. This equipment could be helpful together with laptop to charging devices (cell phone, camera, pocket osciloscope etc.), which are carried with notebook for doing outdoor activities and measurements.
|
|
|
Metal detector for industrial use
Stehno, Rostislav ; Hrabina, Jan (referee) ; Szabó, Zoltán (advisor)
The goal of this project is explore and study the ways of metal detecting and create a metal detector for industrial use. When the device were inventing, a lot of methods were studied and the impulse detect method were chosen as the most perspective way of metal detecting, thanks to a huge electronics parts possibilities. After experiences with preceding device was necessary to redesign it. Main target of this thesis is to increase the computing power of detector. For this purpose will device need a new microcontroller. Device will communicate with PC trough a USB port. The device will have a battery which allows device to run for a few hours. Processing of measured data will be make even with DFT which will lead to better analyze of mass and type of conductor under device.
|
|
|
Industrial programmer Atmel AVR microcontrollers
Gryžboň, Jan ; Hanák, Pavel (referee) ; Pavelka, Ondřej (advisor)
The aim of this thesis is to design and implement an industrial programmer AVR microcontrollers from Atmel. The first section provides the theoretical knowledge of the AVR microcontroller. Furthermore, comparison of methods for programming the microcontroller and the selected method is an analysis of the speed of programming. The following is the entire design of industrial programmer which is implemented in the programming environment Eagle. In the penultimate part of the proposal is designed PCB. The final section is devoted to the revival of the programmer and programming.
|
|
|
Emulator of 3.5" diskette drive using RS232 and SD memory card
Sedláček, David ; Hanák, Pavel (referee) ; Pavelka, Ondřej (advisor)
This thesis deals with the design of the 3,5" floppy drive emulator with ATMEGA microprocessor unit. The emulator has been designed according to the principles of designing electronic devices, there is also object-control application and firmware for a microcontroller, which supports MFM coding. The thesis also lists all the formats of data stored or transmitted along with some flowcharts.
|
|
|
PLC for Smart Metering
Houser, Milan ; Rusz, Martin (referee) ; Mlýnek, Petr (advisor)
This bachelor’s thesis deals with the technology communicating over the electrical power grid, PowerLine Communication (PLC). It solves the principles, possibilities of use, ad-vantages and disadvantages of this technology. The basic issues of communication of PLC networks, Smart Grid and Smart Metering on narrowband PLCs with multiple carriers on the PRIME and G3 standard are discussed. At the end of the work there are measurements on Atmel and Devolo devices. A laboratory task was also created here, which deals with the measurement of narrowband transmission.
|
|
|
Switched power supply with current limiting
Staněk, Michal ; Brančík, Lubomír (referee) ; Kubíček, Michal (advisor)
This thesis is focused on design and construction of switched mode power supply with continuous regulation of output voltage and current. The Power supply is designed as a switching power supply to reduce its weight and dimensions. To reach better parameters, it consists of two separate converters. The first one is isolated step-down controller with transformer. It supplies output the second controller (adjustable) and the measuring section with stable voltage. Input converter is designed as a simple single-transistor flyback converter. The TOPSwitch circuit was selected to reduce number of components. Output bench power supply is non-isolated buck converter with single transistor. For second converter the TL594 was selected as a control circuit, which typical aplication was modified to fulfill requirement of the bench power supply. Processor ATmega16 was used to show both required and actual values of current and voltage on a display.
|
|
|
Integrated stereo amplifier for home audio listening
Jaša, Jakub ; Petržela, Jiří (referee) ; Kratochvíl, Tomáš (advisor)
This bachelor thesis deals with design of a stereo amplifier, which consists of several functional blocks for the analog audio processing. This document describes the solution of individual functional audio blocks, detailed design including schematics and contains also other documents for the construction of the amplifier. The main topic is design, simulation, construction and evaluation of a power amplifier that uses power transistors ThermalTrak. The evaluation of the results of the whole implementation compares measured parameters with other types of amplifiers.
|
|
|
Remote controled robot unit
Kratochvíl, Robert ; Kosina, Petr (referee) ; Pavlík, Michal (advisor)
Labor is handling of the programming movement functions and construction of the simple robot, a design of double-layer printed circuit boards for its implementation and realizes remote control. Motional functions were tested using the test, hand-soldered, double-layer board implemented on soldery bay of joints and demonstrated on prototype. The movements themselves have been simulated using LEDs, the remaining parts were up to the type of casing the same with a planned final design of the board. Using the prototype we demonstrated complete exact movements. For the control microcontroller was chosen for the board of the robot and controller ATMEGA16, communication takes place through USART bus of this microcontrollers. Programming was carried out in CodeVision and AVR Studio, design of printed circuit boards in the EAGLE.
|
guest ::
