|
| |
|
| |
|
|
Membraneless speaker
Kovář, Josef ; Šteffan, Pavel (referee) ; Pavlík, Michal (advisor)
The bachelor thesis consists of theoretic basics and describes the design and construction of one-channel membraneless speaker. Absence of mechanical components gives the membraneless speaker no frequency limitation. The design consists of power source, control electronics, which modulates the signal, convertor and output transformer. The power source is realized by transformer, which lowers the voltage and stabilizators. Modulation is provided by integrated circuit TL 594, its duty is adjusted by potentiometer P1 and frequency by potentiometer P2. Power conversion provides dual forward converter. As a output transformer was used transformer from color television.
|
|
|
Regulated power supply 50V/5A
Herman, Tomáš ; Vorel, Pavel (referee) ; Huták, Petr (advisor)
Bachelor´s thesis deals with the adjustable DC voltage source. The first part deals about the typical involvement of resources and consequently the properties of individual components resources. The second part is the actual design of control circuits, selection of components, wiring and PCB design.
|
|
|
Design of switching class audio power amplifier
Bronec, David ; Kratochvíl, Tomáš (referee) ; Brančík, Lubomír (advisor)
This bachelor thesis is dealing with the issues of the switched category output amplifiers and its aim is to design and to construct a stereo amplifier with the energy output about 100W. The amplifier is constructed in the switched category D. The design of the corrective preamplifier with the correction of depths, heights and the balance functions is also described. Furthermore, this thesis deals with the description of the switched power supply with the TOPswitch control circuit. The design is also supplemented by the simulations and the printed circuits of each part. There are also some photographs of the device and the measurement protocol is included too.
|
|
|
Audio amplifier with PWM for laboratory measurements
Lelek, Martin ; Dřínovský, Jiří (referee) ; Kratochvíl, Tomáš (advisor)
This paper describes about theoretical design of class D power amplifier. Amplifier is primarily intended for laboratory measurements, i.e. measuring of major parameters of amplifier operates in this class (frequency response, slew rate, aliasing etc.). Amplifier (oncoming laboratory module) uses PWM (Pulse Width Modulation) and is constructed from separate blocks for possibility of measuring key signals trough all the structure (triangle comparation wave, analog input signal, feedback signal, PWM signal from modulator, drivers and power transistors, output signal after recontruction filters). Laboratory module is determined for laboratory power supply of safe voltage and should be produce power of several tens of watts into usual load impedance.
|
|
|
Design of a comparator with offset compensation in CMOS technology
Hylský, Josef ; Vávra, Jiří (referee) ; Kledrowetz, Vilém (advisor)
This work contains basic knowledge about comparators and its design in the CMOS technology. The first chapter deals with a wide use of a comparator, its charakteristice and the CMOS technology that is used to produce the transistors for the implementation of comparators. In the two following chapters there are examples of connexion of comparators, the design of the two-stage open loop comparator and improving of its charakteristic. The preamplifier and its application in high-speed Latchs comparators are introduced in the next chapter. The design of the comparator are introduced inthe next chapter. The design of the comparator and its application in high-speed comparators are introduced in the next chapter.
|
|
| |
|
|
Design and construction of automatic galvanic line
Vondruš, Jiří ; Janda, Marcel (referee) ; Melichar, Petr (advisor)
This thesis deals with the design of automated system of electroplating. The first part is centered on designing the technological process for this electroplating and the setout of operating vats. It also deals with the project of mechanical construction, electrical system, with the computing procedure and the optimum choice of gear for galvanic line model. The work includes the design of a DC motor controller, the computing procedure and the construction of heating element for vats heater simulation. The last part of this thesis offers an insight to the control system and the assembled program. In the addendum, the photo of the realized model, the wiring scheme, and the programme transcript for control galvanic line model can be found.
|
|
| |
guest ::
