|
|
Design of magnetic bar-code read head
Kadlčík, Libor ; Drexler, Petr (referee) ; Mikulka, Jan (advisor)
Magnetic bar-code is composed from ferromagnetic bars printed on a substrate. The amount of ferromagnetic material is low, therefore reading magnetic barcode requires sensitive methods. Principle of methods of sensing both low-intensity magnetic field (fluxgates) and detecting low concentration of ferromagnetic material (resonant circuit, differential sensor) will be described. There are sensors producing frequency-modulated signal, therefore we focus on frequency demodulators as well. Signal acquired by sensor suffers from convolution distortion, reconstruction methods will be introduced. The assembled device consists of sensing oscillator, frequency demodulator, amplifier and reconstructing circuit. Frequency demodulation is done by phase-locked loop or differential demodulator. Reconstruction is based on detection of inflection points, producing square signal (representing bars of barcode). Design of these blocks is described. The device is able to read magnetic barcodes and reconstruct convolutionary distorted acquired signal. The differential demodulator exhibits low noise and low temperature drift (contrary to phase-locked loop). Signal produced by reading 2 mm wide bars is reconstructed without any problems, bars of width less than 1 mm cause troubles in certain cases (due to high degree of convolution distortion).
|
|
|
Control Unit for VHF Radio Receiver with Frequency Synthesizer
Sobotka, Martin ; Šebesta, Jiří (referee) ; Vyskočil, Pavel (advisor)
The aim of this work is to propose the involvement of the control unit for receiving VHF radio and its practical implementation. Adding a panel on the appropriate tuner unit leads to a complete receiver to receive radio broadcasts. My work is to focus on two frequency bands: VHF band for broadcasting and VHF band for air radio communication. This paper describes a process of selection of component, their description and integration into a complete circuit, a description of the control program for the microcontroller and a description of control device. Scheme and the draft for the manufacture of printed circuit board is attached.
|
|
|
Spectrum Analyzer up to 500 MHz
Čada, David ; Vimperk), Tomáš Baráth (Rohde Schwarz (referee) ; Šebesta, Jiří (advisor)
This project deals with design and realization of the spectrum analyser using double superheterodyne topology with frequency range up to 500MHz. This work solves hardware blocks like phase lock loops, intermediate frequency filters, saw filter, crystal filter, logarithmic detector. Content of work is also design description and tuning of spectrum analyzer parts.
|
|
|
Synchronized sources of clock signals
Florián, Antonín ; Lazar,, Josef (referee) ; Drexler, Petr (advisor)
This thesis deals with design of synchronized sources of time signal. The first part of the thesis deals with the theory the crystal resonators, crystal oscillators and PLL. The second part of the thesis deals with the crystal oscillator with 10MHz frequency. In the oscillator is use of SC cut crystal. The third part of the work deals with method of synchronization. To synchronization is use of PLL.
|
|
| |
|
|
Frequency Synthesizers
Lapčík, Josef ; Špaček, Jiří (referee) ; Dřínovský, Jiří (advisor)
This diploma thesis concerns with analysis and dividing of frequency synthesizers and design of DDS, PLL synthesizers. Base types of frequency synthesizers are described including differences between methods of their operation. Base circuits of both – DDS and PLL synthesizers and other important circuits are described in details at design part of this thesis. Design of DDS and PLL synthesizer is described in particular sections. Both synthesizers are directly realized and stand-alone control applications are created. PLL synthesizer is also ready to control thru Agilent VEE program environment. Particular example application is designed in Agilent VEE. This application is used as basis of attached lab project.
|
|
|
Gas flow measurement
Kozák, Matěj ; Uher, Miroslav (referee) ; Beneš, Petr (advisor)
This thesis deals with the problem of designing vortex flow meter for a nominal range of 40 l.min-1. It describes the problems of vortex bodies and choice of methods for detection of vortices. The thesis includes solution of various problems in the design, which were published in scientific articles or patents. The following describes the design solution vortex flow meter for the specified range, which uses ultrasonic sensors to vortices detection. The proposed flow meter is calibrated with reference flow meter and compared with commercially produced vortex flow by the TST electronics and Burkert companies, which are designed for the specified ranges.
|
|
|
Laboratory Model of the Vortex Speed Indicator
Kazda, Ondřej ; Kolka, Zdeněk (referee) ; Biolková, Viera (advisor)
This work is concerned with posibility of measuring a wind flow by Von Karman vortex sheed structure. The bluff body is situated in the way of air flow propagation and consequentally vortexes will be appeared. Important part of speedmeter design is measurment chamber must allow to vortex sheed propagation. The transient and the reciever are situated vertically to propagation of flow.The Ultrasonic carrier is transmitted and modulated by freqency of vortex sheeding in measurment chamber.Demodulator uses PLL to “focusing“ detection of the ultrasonic beam. This can be indicated like lock and unlock phase loop. From known value of sheed frequency can be directly calculated speed of flow.
|
|
| |
|
|
Power source for pulse magnetron sputtering
Schulz, Jakub ; Magát, Martin (referee) ; Šteffan, Pavel (advisor)
The presented thesis deals with the design and assembly of the generator for pulse magnetron sputtering. The designed device is capable of generating two square wave signals via its counter-working outputs. Both signals have independently adjustable frequency, pulse count and duty ratio. Both signals originate from two frequency syntheses controlled by microcontroller PIC16F877A. All the settings are entered by four buttons and are shown on an alphanumeric display with 16x4 characters. The duty ratio is adjusted using a special module.
|
guest ::
