|
Trade and office centre
Lupač, Zbyněk ; Buchta, Stanislav (referee) ; Bajer, Miroslav (advisor)
The diploma thesis deals with the structure design of steel frame of a storeyed building housing a shopping and administration centre in the area near Rokycany. The building consists of a truss cylinder tower structure with 11.165 m in diameter, nine storeys and the height of 33.3 m, connected to a rectangle part by means of a steel bridge structure 3.6 m long. The frame of the rectangular part, 26.8 m wide and 45 metres long, has three altitude levels with flat roofs, suitable and non-suitable for walking. The interior of the building is divided into two parts, connected at the outskirts, by a covered atrium. The design height is 3.7 m. The structure is designed of steel S235. The thesis contains the technical report, static calculation, outputs of a program, the record of the material and design documentation. Two versions were considered; the more convenient one is further processed.
|
|
The steel structure of a sports hall
Vaněček, Milan ; Pilgr,, Milan (referee) ; Štrba, Michal (advisor)
Master thesis is focused on design of steel roofing structure of sports hall. Construction is located in town of Jihlava. Proportions and disposition are in accordance of assignment of master thesis. The proportions are 40m x 60m, the height of structure is approximately 15m. Two versions of roof structure were designed – truss beam with shape of lentil and double reverse truss girders (girland truss). These versions were tentatively analyzed and designed for the main bearing members. Afterwards both of the versions were appraised and one of the versions was chosen for detailed treatment. It means there was attention focused on design of important details, creating of drawing documentation and technical report, all in the range of thesis supervisor. The valid Eurocodes were used.
|
|
Design of manipulator for hemp insulating mat stacking
Kočiš, Petr ; Drlík, Michal (referee) ; Blecha, Petr (advisor)
Bachelor's thesis deals design of manipulator for hemp insulating mat stacking. It defines a field of aplication of an equipment and deals with a design solution versions. It also deals with a structure of chosen version and a calculation. The calculation is devided into a preliminary calculation, a kinematics analysis, a static analysis and a control calculation. Safety- checking of elements due to limit state flexibility is a result of a control calculation. An economic analysis follows after it. It concerns calculating the cost of materials, normalized components, modular components and other components.
|
|
Automatic Control of the Manual Air-condition in the car
Zajíc, Jakub ; Kratochvíl, Tomáš (referee) ; Říčný, Václav (advisor)
This bachelor’s theses deal with possibility of realization manual air-conditioning adaptor analysis, which would enable automatic adjusting of elected temperature into a car. Part of this analysis is block proposal of type of analog and digital construction of automatic air-conditioning adaptor. Both block diagrams are accompanied with functional description. Due to pro-and-con evaluation of both types of construction was decided to realize analog version of air-conditioning. Detail partial functional description of functional blocks and analytical analysis of its influence to general temperature adjusting accuracy are presented. Within bachelor’s theses is performed circuit proposal of all partial blocks of manual air conditioning adaptor. Component of proposal is creating of all bases for construction of functional equipment model. Final phase of bachelor's theses deal with realization of functional adaptor model and its calibration for measuring and temperature control into a car.
|
|
Micro-hydraulics system design
Pitaš, Martin ; Marada, Tomáš (referee) ; Věchet, Stanislav (advisor)
One of the main aims of presented bachelor's thesis is an implementation of hydraulic circuit by micro-hydraulics system. Bachelor's thesis has three main part. First part deals with hydraulic distribution and selection of acceptable devices of hydraulic circuit, especially their advantageousness in term of finance. Second part is devoted to the construction of fixation for the position sensor on linear hydromotor, holder for hydraulic valve and hydrogenerator. Third part describes to hydraulic circuit, right hydraulic oil for whole hydraulic circuit. The verifying calculation confirming rightness selection particular devices is here also. Autodesk Inventor Professional 2008 (chapter 3) a FluidSIM Hydraulics V 4.2 Demo Version English (chapter 4) was used as a general software.
|
|
Buried bridge
Skurčák, Martin ; Požár, Michal (referee) ; Panáček, Josef (advisor)
This bachelor thesis is foucused on design buried frame monolithic road bridge. The bridge is situated on Road I/9 between village Vehlovice and Liběchov. The primary funkcion of bridge is crossing moat. There are three preliminary versions designed, burried monolithic road bridge. The project includes statical analysis and drawing documentation.
|
|
Reinforced arch bridge over the Krupá river
Adler, Filip ; Pěkník, Robin (referee) ; Koláček, Jan (advisor)
This Bachelor thesis deals with the design of new bridge situated in place of an original one in Staré Město pod Sněžníkem. The original bridge is used to transfer the traffic of local road built in category of S7,5 over the Krupá river. Its construction system is designed as an arch with upper deck, with a span of 18m. Loads and construction assessment correspond to Eurocode. Calculations were performed via Scia Engineering software, version 2013.0.
|
|
The roof structure of the industrial hall in Kyjov
Nosková, Nela ; Pilgr, Milan (referee) ; Šmak, Milan (advisor)
The Bachelor´s thesis describes design and static assessment of the main roof structure supporting elements of the roof structure of the industrial hall in Kyjov. The hall is designed from timber. The aisle is rectangular floor plan 17,0 x 40,0 m. The main bearing structure causes as a frame truss supported by columns. Solid frame is made from solid timber C24. Purlin is designed from solid timber C24. The static calculation also includes fire resistance reports of single elements. Static analysis has been accomplished by student version of the SCIA Engineer 2012 software.
|
|
New building with establishment
Kouřilová, Vendula ; Hlavsa, Petr (referee) ; Kolář, Radim (advisor)
The subject of this bachelor's thesis is a design of family house with establishment in Kyjov - Netcice. It includes all the detailed drawings of the building. The house is designed for a family of four. Built-up area is 127.58 m2 and 1254.06 m3. The building is situated in the north of Kyjov in a peaceful town part Netcice. The building is located on two adjacent parcels, which are intended to be built-up by the Land-use Plan. Land is gently sloping from the southwest to northeast. The building is completely basement. In the basement is located establishment. It is a small business - production of peristaltic and dosing pumps. Vertical construction of the basement are lined with concrete blocks, vertical construction of the upper floors are lined with lime-sand blocks. The roof is hip in slant. Design emphasizes, inter alia, on static and appropriate layout, thermal properties of constructions, fire safety of the building, etc. Drawings, charts and visualization have been processed in educational version of design software ArchiCAD.
|
|
What is the Predicative Ability for Unemployment Rate of Different Methodologies for Output Gap Estimation?
Holá, Martina ; Kubíček, Jan (advisor) ; Chytil, Zdeněk (referee)
The submitted diploma thesis is dedicated to the calculation of the estimation of output gap by three estimating techniques (Hodrick-Prescott filter, Kalman filtering, and Cobb-Douglas production function) for the Czech Republic during the years 1995-2009, and, consequently, to their usefulness for testing the Okun's law as a suitable predicative tool. In other words, which of the mentioned methods is the most appropriate one for an accurate prediction of the rate of unemployment. To achieve this, the Box-Jenkins methodology is used for modelling and designing the cyclical unemployment forecasts and dynamic version of the Okun's law. The results indicate that, for the given period, there is relatively strong and unstable relationship between changes in output gap and changes in cyclical unemployment in the Czech Republic. The most suitable technique for the estimating of the future development of unemployment gap seems to be the Cobb-Douglas production function approach. This is namely based on the quantity of gained forecast errors and Granger causality.
|
guest ::
