|
|
Control system for cantilever gates
Koždoň, Ondřej ; Arm, Jakub (referee) ; Bradáč, Zdeněk (advisor)
The goal of this bachelor's thesis is to design a battery powered control system for wireless controlling swing gate (may be used for cantilever sliding gates or garage doors). This system is designed as a small electronic system with necessary Inputs/Outputs (I/O) and an Input for charging a battery from solar cells. The result of this bachelor's thesis are two main PCBs with dimensions of 5×5cm for controlling the gate and remote controller with dimensions of 2,3×4,4cm. Main PCB allows adding more remotes, deleting all remotes and modes for the way of controlling the gate (opposite direction, open only, close only, open wing, close wing, stop the gate) and selecting Master/Slave gate. Communication works on frequency of 434MHz.
|
|
|
Field Programmable Gate Arrays Usage in Industrial Automation Systems
Nouman, Ziad ; Kadaník,, Petr (referee) ; Kobrle,, Pavel (referee) ; Klíma, Bohumil (advisor)
Tato disertační práce se zabývá využitím programovatelných hradlových polí (FPGA) v diagnostice měničů, využívajících spínaných IGBT tranzistorů. Je zaměřena na budiče těchto výkonových tranzistorů a jejich struktury. Přechodné jevy veličin, jako jsou IG, VGE, VCE během procesu přepínání (zapnutí, vypnutí), mohou poukazovat na degradaci IGBT. Pro měření a monitorování těchto veličin byla navržena nová architektura budiče IGBT. Rychlé měření a monitorování během přepínacího děje vyžaduje vysokou vzorkovací frekvenci. Proto jsou navrhovány paralelní vysokorychlostní AD převodníky (> 50 MSPS). Práce je zaměřena převážně na návrh zařízení s FPGA včetně hardware a software. Byla navržena nová deska plošných spojů s FPGA, která plní požadované funkce, jako je řízení IGBT pomocí vícenásobných paralelních koncových stupňů, monitorování a diagnostiku, a propojení s řídicí jednotkou měniče.
|
|
| |
|
|
Semiconductor laser driver for 1Gbit/s
Chlachula, Filip ; Křivák, Petr (referee) ; Prokeš, Aleš (advisor)
This master´s thesis deals with a solution of the driving circuits of semiconductor laser. In the beginning of the thesis there is an analysis of semiconductor lasers and its characteristics. Then the principle of laser diodes and its excitation is described. This thesis is focused on semiconductor laser excitation through the use of direct and modulating current. Several circuits are described, designed and simulated. The best resulting circuit is realized and measured in the laboratory.
|
|
|
Laboratory board demonstrates CAN bus
Levek, Vladimír ; Fedra, Zbyněk (referee) ; Frýza, Tomáš (advisor)
The goal of this thesis, is proposal of the laboratory board demonstrates communication by the help of bus CAN. Laboratory boards, controlled with microprocessor, will be send statuses inputs and outputs with each other. Also it will can be transmit and receive messages by the help of the serial port RS-232. With protocol CAN will be send this information: Temperature, Lighting, Analog input 0 - 5 V, Analog output 0 - 5 V, Digital input level TTL and digital output type open collector.
|
|
|
Research in the Field of Anhydrite Binders
Břicháčková, Jana ; Smetanová, Lenka (referee) ; Gazdič, Dominik (advisor)
The presented work deals with research in the field of sulfate binders on the anhydrite base. Conceptually, it is divided into a general theory of sulfate binders and anhydrite mortar compounds, which is describing in detail the using of anhydrite mortar compounds on the poured floor screeds, and then the experimental part, where is made the mineralogical analysis of seven different gypsum resources and subsequent is monitored the effect of two sulfate exciters on the achieved technological properties and hydration process.
|
|
|
Design of switching class audio power amplifier
Bronec, David ; Kratochvíl, Tomáš (referee) ; Brančík, Lubomír (advisor)
This bachelor thesis is dealing with the issues of the switched category output amplifiers and its aim is to design and to construct a stereo amplifier with the energy output about 100W. The amplifier is constructed in the switched category D. The design of the corrective preamplifier with the correction of depths, heights and the balance functions is also described. Furthermore, this thesis deals with the description of the switched power supply with the TOPswitch control circuit. The design is also supplemented by the simulations and the printed circuits of each part. There are also some photographs of the device and the measurement protocol is included too.
|
|
|
Traction DC/AC inverter 2,5kW for an induction machine of an electric garden tractor
Krist, Petr ; Patočka, Miroslav (referee) ; Vorel, Pavel (advisor)
This thesis deals with the proposal of power 3-phase DC/AC inverter for an induction machine of small garden tractor. It concerns the choice of a voltage level of DC link, dimensioning of the power circuit, drivers for power transistors, implementation of metering and protection and also processor driving. The whole thing ends at proposal of PCB in the software program called EAGLE and PCB manufacturing. So we also check if the theoretical calculations are correct and if the whole drive works.
|
|
|
Hybrid headphone amplifier for the high-end listening and performance
Čacký, Adam ; Šotner, Roman (referee) ; Kratochvíl, Tomáš (advisor)
This bachelor´s thesis describes the design of a high quality small portable headphone amplifier for dynamic headphones. Part of the work is theoretical assumptions for the optimal design and implementation of peripheral involvement, comparing the properties of components used and the resulting parameters of modeled device. Analyses of the electrical quantities of the circuit created in simulation software are enclosed.
|
|
|
Converter for high-speed induction motor
Veselý, Petr ; Pazdera, Ivo (referee) ; Procházka, Petr (advisor)
The semestral thesis deals with designing a frequency changer. It describes general information about induction motors and power electronics, focusing on pulse converters. Based on given parametres, appropriate components were chosen and described. Also, there is power loss calculated in this document, which is used for dimensioning cooling. Also an LC filter is designed in this dokument. At last, there is a printed circuit board designed for the power part.
|
guest ::
