|
|
Determination of Q/h characteristics of spillways of the sluice chamber of the Brno-Modřice WWTP in conditions of influenced flow
Škrancová, Markéta ; Ježek, Jiří (referee) ; Žoužela, Michal (advisor)
The work deal with the measurement, processing and analysis of Q/h characteristics of the sluice chamber in the wastewater treatment plant on a physical hydraulic model in the conditions of influencing the overflow phenomenon by the groundwater level. Based on the achieved results, a measuring system has been projected in the area of the sluice chamber to measure the flow and flow rate of lightened water into the Svratka river. The measurements on the model were performed in the premises of the Laboratory of water Management Research of the Institute of Water Structures of the Faculty of Civil Engineering of Brno University of Technology by the author of this work. The results of the diploma thesis is a flow chart describing the calculation procedure used to determine the immediate flow, on the basis of which a new software of the evaluation unit of the measuring system was realized.
|
|
|
Workplace for automated conductivity measurement of liquids
Rajm, Martin ; Fialka, Jiří (referee) ; Havránek, Zdeněk (advisor)
Its aim the present Dissertation is to create a workplace for automated measurement of conductivity of liquids. Theoretical part describes principles and methods of measurement of conductivity of liquids and also measurement of temperatures of solutions. The reader is then made familiar with the program and development environment known as LabVIEW in which the measurement software has been created as well. This software serves also for the control of the LCR meter “HIOKI 3532-50” whose characteristic properties, control method and possibilities of measurement are briefly characterized in subsequent parts. The text includes also a mention about the GP-IB bus, thanks to which the LCR meter is able to communicate with PC. The actual liquid which is to be analyzed comes into contact, however, only with the four-electrode conductivity cell “WTW TetraCon 325” which is described in the Dissertation as well. The theoretical part is concluded with presentation of the multifunction card “NI USB-6008”, with the help of which the temperature of the solution analyzed is determined. In the practical part is description of the connection and explanation of the function of the measurement system as a whole. This is followed by a presentation of the actual measurement software intended for conductivity measurement. Both its structure, functions and some information about control are described there. This part of the Dissertation deals also with determination of the values of the elements of the conductivity probe replacement circuit and with the impact of measurement parameters on resulting measurement values.
|
|
|
Thermoluminescence measurement system
Matějka, Tomáš ; Král, Jan (referee) ; Kubíček, Michal (advisor)
This thesis deals with revision and design of electronic for measuring system PSI TL 500 which is designed for measurement of thermoluminescence phenomena in photosystem II. Thesis describes principles and properties of the measuring system in its current form and changes for the new version are discussed. Digital control part based on Xilinx Zynq platform is designed. Revision of analog measuring part of system is made and partial changes are implemented.
|
|
|
Determination of the Q/h characteristic of storm water overflow chamber
Škrancová, Markéta ; Ježek, Jiří (referee) ; Žoužela, Michal (advisor)
The main task of this bachelor thesis is to determination the Q / h characteristics of the sluice chamber in the wastewater treatment plant on a physical hydraulic model, processing of all measured values and their analysis. All measurements were performed by the author of this work in the premises of the Laboratory of Water Management Research of the Institute of Water Structures of the Faculty of Civil Engineering of the Brno University of Technology. The result of the bachelor thesis is an equation used to determine the immediate flow which will be entered into to evaluation unit of the newly built measuring system. It will be located in the sluice chamber of the wastewater treatment plant and will be used to measure the flow and flowed amount of overflow water into the Svratka River.
|
|
| |
|
|
Low-level measurement methods
Müller, Tomáš ; Steinbauer, Miloslav (referee) ; Fiala, Pavel (advisor)
This bachelor thesis discuss about low-level measurement methods. Also is outline the method, how to proceed in lay-out of measurement system and in selection of measurement device and its accessories. Thereinafter is stated the calculation of mistakes and in recent time also the calculation of often use mazes. Without them would be not the result total. Next part of this bachelor theses pointed to practical measurement in the area of low level current and voltage, where are shown and described wiring types used for these measurements. Next chapters discuss about measurement principles low level electric current and voltage. Than try to point to appearance, which indisposed participace on measurement accuracy and try to introduce with steps, which helps to reduce this effects. These voltages and currenties are in normal measurement insignificant, but in the low-levels influence they the result too much. Thereinafter is described the principle of measuring amplifier and closer mentioned parameters and usage of instrumentation amplifier with ultra low input bias current INA 116. Next to last point of this bachelor thesis is an example of usage this network in measurement with gerdien condenser. Therein is clarify its physical principle and proposal parameters. In the last part is described the air ions concentration measurement with gerdien condenser. Also are described the results of measurement and results of this.
|
|
|
THE USE OF ELETRONIC MEASURING SYSTEMS FOR MONITORING STRUCTURES
Kovács, Pavel ; Zich, Miloš (referee) ; Doc.Ing. Karel Kubečka, Ph.D (referee) ; Daněk, Petr (advisor)
This thesis deals with the use of the electronic measuring systems for monitoring structures. The first part of this work is focused on mapping the available measuring systems for monitoring deformations and strains, from the point of their measurement accuracy, the real advantages and disadvantages, including examples of monitoring of constructions. In the second part were selected measuring systems for monitoring strains and deflection interest structure. Subsequently, the measuring system with online recording into the tested roof structure was installed and the loading test was performed. Obtained data were compared with other two independent measurements. In the last part of the thesis, the measured values of each independent measurements were compared together, and with the values calculated from the mathematical model. The achieved results show that the installed monitoring system is capable to reliably measure deformation of the structure in real time and thus to warn the building administrator against the potential danger in advance.
|
|
|
Crosswind Sensitivity of Road Vehicles
Vančura, Jan ; Dundálek, Radim (referee) ; Kaplan, Zdeněk (referee) ; Píštěk, Václav (advisor)
The aim of the thesis is to devise a methodology which is capable of reliable evaluation of road vehicle’s crosswind sensitivity. The work consists of writing the mathematical model of a vehicle which includes aerodynamic loads and conducting a validation by means of technical experiment as defined by ISO 12021. A sensitivity analysis describing the influence of individual inputs on evaluation criteria of vehicle’s crosswind sensitivity is performed using the model, thereby establishing the overall model error caused by possible inaccuracies of input parameters. At the end, the relationship between discrete pressures on the surface of the vehicle in several aerodynamic configurations and the properties representing the vehicle’s motion is presented.
|
|
| |
|
|
Modelling of differential current amplifier
Polák, Josef ; Šotner, Roman (referee) ; Jeřábek, Jan (advisor)
The aim of my diploma thesis was programming of systems for measuring AC, DC and impedance measurements. Each measuring system measures selected characteristics of current amplifier with controllable amplification DACA_N. Control programs I have created in Agilent VEE Pro 9.2. The measured data are stored to executable files in MS Excel for further processing. With created measurement programs I made measurements of eight current amplifiers. The results of individual measurements I compiled into graphs and compared with each other circuit characteristics of amplifiers. Then there is described controlling and connection of current amplifier and its construction. At the end the diploma thesis describes amplifiers with the worst and the best measured circuit characteristics. The measured values show that the amplifier DACA_N with slight differences works by theoretical assumptions and measurement systems suggested by me work with no problem.
|
guest ::
