|
|
Analysis of possibilities to improvement induction motors efficiency
Novotný, Jiří ; Hájek, Vítězslav (referee) ; Mach, Martin (advisor)
In the first part of the master’s thesis dealing with the increasing efficiency of induction motors there are briefly presented basic information about induction motors, followed by an overview of the losses of induction motors. The next part deals with the ways to increase efficiency of induction motors without increasing tooling costs. The practical part consists of four measurements of four induction motors, with their various mechanical adjustments to make comparing benefits of these modifications possible. The measured results are compared by a finite element method in Maxwell 2D Design program, in which the same motors are simulated as measured. Theoretical knowledge about the increase of efficiency is practically applied while being implemented in the simulations.
|
|
|
Three-phase induction machine fed by frequency inverter
Fiala, Zbyněk ; Huzlík, Rostislav (referee) ; Vítek, Ondřej (advisor)
The thesis analyses losses in the three phase induction motor with a focus on iron losses. In the first instance the three phase induction motor and the losses in it are described. The analytical calculation and the simulations in the RMXprt software are performed. The measurements were made with a different frequency (40, 50, 60Hz) and behaviour of supply voltage on a motor TM90-2S by EMP Slavkov. In conclusion the results of calculation, simulation and measurements are compared.
|
|
|
Losses analysis of small induction motors
Šišák, David ; Cipín, Radoslav (referee) ; Mach, Martin (advisor)
This bachelor thesis deals with analysis of losses of small induction motors. The first part of the project introduces the principle of operation and construction of induction motors. Furthermore, there is dealt with issuing each losses, their origin and disposition in induction motor. The project continues performing the analytical computation of the losses of induction motor with an output of 600 W. The losses of the motor are also calculated in the program Maxvell RMxprt. In the practical part, there are the results of the laboratory measurement on that motor and measurements concerning two another small induction motors different in nominal power. In the last part, there are compared the results of individual motor losses, obtained by computations and measuring. There are also compared the measuring results of losses of chosen motors depending on the nominal output.
|
|
| |
|
|
Analysis of core loss of a small induction machine
Plíšek, Oldřich ; Cipín, Radoslav (referee) ; Mach, Martin (advisor)
The aim of this master´s thesis is to analyze core losses of a small induction motor. Analyzed values are obtained from laboratory measurements, software analysis and 2D finite element method simulation. The theoretical part of this thesis consists of two parts. The analysis of the higher spatial harmonics presents in the induction motor and the analysis of core losses of the motor. Practical part consists of laboratory measurements according to ČSN. Measured values are used to calculate individual losses. The next part consists of creating a model for software analysis (Maxwell RMxprt). The generated model is converted into a 2D simulation environment (Maxwell 2D), where it is adapted to obtain values from the examined parts (rotor and stator teeth and rotor cage). Results of simulations at different loads are compared and analyzed from the point of view of higher harmonics.
|
|
|
Low power electrical machines
Martinek, Radek ; Mach, Martin (referee) ; Hájek, Vítězslav (advisor)
The master’s thesis introduces various types of electric motors. Overall, it is divided into 6 chapters, which the first deals with special type of electric motors, namely: permanent magnet DC motor with coreless winding, piezoelectric motor and three phase induction motor with solid rotor. For all of these motors are introduced principles, types, advantages, disadvantages and applications. The second part of thesis deals with perspective types of motors, namely: single phase induction motor and reluctance motor. For all of these motors are introduced principles, types, advantages, disadvantages and applications. The third chapter deals with analysis parameters of single phase induction motor. The analysis is performed on a borrowed motor from ATAS company by measurement and verification using simulation program Ansys Maxwell. The fourth part discusses the possibilities of increasing the effectiveness of borrowed electric motor. The following is chapter five, which deals with increasing the efficiency of the motor by changing metal sheets. Results are verified by simulations with Ansys Maxwell and measurements on sample of electric motor. The last part presents electric motor design with new selected electric sheets with lower specific losses, but also with lower magnetic induction.
|
|
|
Analysis of steel grade influence on small induction machine efficiency
Plíšek, Oldřich ; Klíma, Jiří (referee) ; Mach, Martin (advisor)
The theoretical part of the bechelors thesis examining the impact of the material of the magnetic circuit on the efficiency of induction motors is devoted to analysis of the induction motor and its losses. It also describes the measuring, including calculations of individual losses. Another theoretical part examines the impact of specific losses on the magnetization characteristics of assessed laminations. The practical part includes laboratory measurements of single phase and three phase motors ATAS Electromotory Náchod brand with multiple types of laminations. Measured values are used to calculate individual losses, which are later mutually compared. Models of measured motors with multiple types of laminations are simulated with the aid of ANSYS Maxwell RMxprt program. Analysis of engines with specific types of laminations are performed with the aid of analytical calculations. Results of calculations are compared with simulated and measured values.
|
|
|
LOSSES IN MEDIUM VOLTAGE CURRENT TRANSFORMERS
Bajánková, Denisa ; Langerová, Petra (referee) ; Baumgartnerová, Alena (advisor)
Tato bakalářská práce umožňuje nahlédnout do problematiky ztrát u přístrojových transformátorů proudu vysokého napětí. Přístrojové transformátory proudu představují velmi důležitou součást elektrických zařízení, slouží k transformování měřených proudů na standardní hodnoty, které měřicí a jistící přístroje mohou zpracovat. Je důležité, aby tyto proudy byly převáděny s co nejvyšší přesností. Teoretická část práce se zaměřuje na popis přístrojových transformátorů proudu a analýzu jednotlivých ztrát u transformátoru. Praktická část je obsažena v deváté kapitole, má za cíl ověřit teoretické poznatky práce a popisuje laboratorní měření.
|
|
|
Losses analysis of small induction motors
Šišák, David ; Cipín, Radoslav (referee) ; Mach, Martin (advisor)
This bachelor thesis deals with analysis of losses of small induction motors. The first part of the project introduces the principle of operation and construction of induction motors. Furthermore, there is dealt with issuing each losses, their origin and disposition in induction motor. The project continues performing the analytical computation of the losses of induction motor with an output of 600 W. The losses of the motor are also calculated in the program Maxvell RMxprt. In the practical part, there are the results of the laboratory measurement on that motor and measurements concerning two another small induction motors different in nominal power. In the last part, there are compared the results of individual motor losses, obtained by computations and measuring. There are also compared the measuring results of losses of chosen motors depending on the nominal output.
|
|
|
Three-phase induction machine fed by frequency inverter
Fiala, Zbyněk ; Huzlík, Rostislav (referee) ; Vítek, Ondřej (advisor)
The thesis analyses losses in the three phase induction motor with a focus on iron losses. In the first instance the three phase induction motor and the losses in it are described. The analytical calculation and the simulations in the RMXprt software are performed. The measurements were made with a different frequency (40, 50, 60Hz) and behaviour of supply voltage on a motor TM90-2S by EMP Slavkov. In conclusion the results of calculation, simulation and measurements are compared.
|
guest ::
